The MINMAX MA01H series is a new range of isolated 1W DC/DC converter modules in a small SIP-package. There are 24 models available with 5V, 12V
or 24VDC input. These products provide have a typical load regulation of 3.5% to 5.5% depending on model.
The MA01H DC/DC converters are a compromise between a more expensive fully regulated converter and a non-regulated converter. They offer the
designer a new solution for many cost critical applications where the output voltage variation has to be kept in a certain limit under all load conditions.
Model Selection Guide
Model
Number
Input
Voltage
(Range)
VDC
Output
Voltage
VDC
5
9
12
15
5
9
12
15
5
9
12
15
Output Current
Max.
mA
200
110
84
67
200
110
84
67
200
110
84
67
Min.
mA
4
2
1.5
1
4
2
1.5
1
4
2
1.5
1
Input Current
@Max. Load
mA(typ.)
238
229
231
230
99
96
95
95
50
48
48
48
@No Load
mA(typ.)
30
Load
Regulation
% (max.)
6.2
5.5
5.5
5
5
3.3
3.6
2.9
5
3.5
3.5
3
Reflected
Ripple
mA(typ.)
11
Max. capacitive
Load
µF
220
@Max. Load
%
84
86.5
87
87.5
84
86
88
88
84
86.5
87.5
87.5
Efficiency
(typ.)
MA01-05S05H
MA01-05S09H
MA01-05S12H
MA01-05S15H
MA01-12S05H
MA01-12S09H
MA01-12S12H
MA01-12S15H
MA01-24S05H
MA01-24S09H
MA01-24S12H
MA01-24S15H
5
(4.5 ~ 5.5)
12
(10.8 ~ 13.2)
24
(21.6 ~ 26.4)
12
5
220
11
4.7
220
Input Specifications
Parameter
Input Surge Voltage (1 sec. max.)
24V Input Models
5V Input Models
12V Input Models
5V Input Models
Model
Min.
-0.7
4.5
-0.7
Typ.
---
5
---
Max.
18
9
Unit
-0.7
---
Input Voltage Range
Reverse Polarity Input Current
Internal Filter Type
Internal Power Dissipation
24V Input Models
All Models
12V Input Models
21.6
---
10.8
24
---
12
26.4
0.3
13.2
A
mW
5.5
30
VDC
---
---
Internal Capacitor
450
Output Specifications
Line Regulation
Parameter
Load Regulation
For Vin Change of 1%
Io=20% to 100%
Conditions
Min.
---
Ripple & Noise (20MHz)
Temperature Coefficient
Short Circuit Protection
---
See Model Selection Guide
±0.01
30
±0.02
60
±1.05
Typ.
Max.
±1.2
Unit
%
---
mV
P-P
%/℃
0.5 Second Max.
E-mail:sales@minmax.com.tw
Tel:886-6-2923150
2013/01/23 REV:6
Page 1 of 4
DC/DC CONVERTER 1W,
SIP-Package
MA01H SERIES
General Specifications
I/O Isolation Voltage (rated)
I/O Isolation Test Voltage
I/O Isolation Resistance
Switching Frequency
MTBF (calculated)
Safety Approvals
Parameter
Flash tested for 1 Second
100KHz, 1V
MIL-HDBK-217F@25℃, Ground Benign
1000 VDC
60 Seconds
Conditions
3300
10
30
3000
Min.
Typ.
---
---
Max.
---
---
VDC
G
V
PK
pF
Unit
I/O Isolation Capacitance
CSA 60950-1 recognition,IEC/EN 60950-1(CB-scheme)
2,000,000
50
100
---
60
---
120
---
---
120
Hours
KHz
Input Fuse
500mA Slow-Blow Type
5V Input Models
200mA Slow-Blow Type
12V Input Models
100mA Slow-Blow Type
24V Input Models
Environmental Specifications
Case Temperature
Operating Ambient Temperature Range (See Power Derating Curve)
Storage Temperature Range
Humidity (non condensing)
Cooling
Parameter
Natural Convection
Conditions
Min.
-40
---
---
Max.
+95
95
+85
Unit
℃
℃
% rel. H
℃
℃
-50
Free-Air convection
---
+125
Lead Temperature (1.5mm from case for 10Sec.)
260
Power Derating Curve
100
80
60
40
20
0
~
Natural
Convection
20LFM
Output Voltage Tolerance
+20%
+15%
+20%
+15%
Output Voltage(%)
100LFM
200LFM
400LFM
+10%
Max.
+10%
+5%
Typ.
+5%
Vnom
Min.
Vnom
-5%
-5%
-10%
0%
20%
40%
60%
80%
-10%
100%
-40
50
60
70
80
90
100
110
Output Load Current (%)
Ambient Temperature
Notes
1
2
3
4
5
6
7
Specifications typical at Ta=+25℃, resistive load, nominal input voltage and rated output current unless otherwise noted.
Ripple & Noise measurement bandwidth is 0-20MHz.
These power converters require a minimum output loading to maintain specified regulation, operation under no-load conditions will not damage these
modules; however they may not meet all specifications listed.
All DC/DC converters should be externally fused at the front end for protection.
Other input and output voltage may be available, please contact factory.
That “natural convection” is about 20LFM but is not equal to still air (0 LFM).
Specifications are subject to change without notice.
E-mail:sales@minmax.com.tw
Tel:886-6-2923150
2013/01/23 REV:6
Page 2 of 4
DC/DC CONVERTER 1W,
SIP-Package
MA01H SERIES
Package Specifications
Mechanical Dimensions
19.5 [0.77]
Pin Connections
Pin
1
2
5
7
Function
+Vin
-Vin
10.2 [0.40]
0.5 [0.02]
+Vout
-Vout
0.50
[0.02]
2.4
[0.09]
2.54
[0.10]
7.62
[0.30]
5.08
[0.20]
[0.13]
3.2
T=6.1[0.24] for 5V & 12V Input Models
T=7.1[0.28] for 24V Input Models
18.5 [0.73]
Bottom View
T
1
2
5
7
►All
dimensions in mm (inches)
►Tolerance:
X.X±0.25 (X.XX±0.01)
0.25 [0.01]
1.3 [0.05]
0.50
[0.02]
►
Pins ±0.05(±0.002)
X.XX±0.13 ( X.XXX±0.005)
Physical Characteristics
Case Size (5&12V Input)
Case Size (24V Input)
Case Material
Pin Material
Weight (5&12V Input)
Weight (24V Input)
:
:
:
:
:
:
19.5x6.1x10.2mm (0.77x0.24x0.40 inches)
19.5x7.1x10.2mm (0.77x0.28x0.40 inches)
Non-Conductive Black Plastic (flammability to UL 94V-0 rated)
Alloy 42
2.2g
2.6g
E-mail:sales@minmax.com.tw
Tel:886-6-2923150
2013/01/23 REV:6
Page 3 of 4
DC/DC CONVERTER 1W,
SIP-Package
MA01H SERIES
Test Setup
Input Reflected-Ripple Current Test Setup
Input reflected-ripple current is measured with a inductor Lin (10µH) and Cin (1µF, ESR < 1.0 at 100 KHz) to simulate source impedance. Capacitor Cin, offsets
possible battery impedance.
Current ripple is measured at the input terminals of the module, measurement bandwidth is 0-500 KHz.
To Oscilloscope
+
Battery
+
Lin
+Vin
Current
Probe
+Out
Load
DC / DC
Converter
-Vin
-Out
Cin
Peak-to-Peak Output Noise Measurement Test
Use a Cout 0.33µF ceramic capacitor. Scope measurement should be made by using a BNC socket, measurement bandwidth is 0-20 MHz. Position the load
between 50 mm and 75 mm from the DC/DC Converter.
+Vin
Single Output
DC / DC
Converter
-Vin
-Out
+Out
Copper Strip
Cout
Copper Strip
Scope
Resistive
Load
Technical Notes
Maximum Capacitive Load
The MA01H series has limitation of maximum connected capacitance at the output. The power module may be operated in current limiting mode during start-up,
affecting the ramp-up and the startup time. For optimum performance we recommend 220µF maximum capacitive load for devices.
The maximum capacitance can be found in the data sheet.
Input Source Impedance
The power module should be connected to a low ac-impedance input source. Highly inductive source impedances can affect the stability of the power module. In
applications where power is supplied over long lines and output loading is high, it may be necessary to use a capacitor at the input to ensure startup.
Capacitor mounted close to the power module helps ensure stability of the unit, it is commended to use a good quality low Equivalent Series Resistance (ESR < 1.0
at 100 KHz) capacitor of a 2.2µF for the 5V input devices, a 1.0µF for the 12V input devices and a 0.47µF for the 24V devices.
+
DC Power
Source
-
+
Cin
-Vin
-Out
+Vin
DC / DC
Converter
+Out
Load
Output Ripple Reduction
A good quality low ESR capacitor placed as close as practicable across the load will give the best ripple and noise performance. To reduce output ripple, it is
recommended to use 1.0µF capacitors at the output.
+
DC Power
Source
-
-Vin
+Vin
Single Output
DC / DC
Converter
-Out
+Out
Cout
Load
Thermal Considerations
Many conditions affect the thermal performance of the power module, such as orientation, airflow over the module and board spacing. To avoid exceeding the
maximum temperature rating of the components inside the power module, the case temperature must be kept below 95℃. The derating curves are determined from
measurements obtained in a test setup.
Position of air velocity
probe and thermocouple
15mm / 0.6in
50mm / 2in
Air Flow
DUT
18, Sin Sin Road, An-Ping Industrial District, Tainan 702, Taiwan
Every time I encountered setbacks in job hunting, I would slowly comfort myself in my heart, "I am a talent, I will definitely find a job that suits me". In a blink of an eye, a month passed. I though...
[size=4]The activities are very unexpected. Many of the chips I applied for or purchased, and the development tools I designed myself are kept in the company, so I can only upload some boards at home!...
I followed the instructions at http://www.hzlitai.com.cn/bbs/viewthread.php?tid=11487&pid=67161&page=1&extra=#pid67161 to join. I didn't expect that when the system started, it would keep printing Eva...
I want to use MFC to write a virtual CD-ROM drive program, but I don't know where to start. Can any expert introduce its programming ideas? Thank you!...
First of all, we must understand what is UART ?The full name of UART is Universal Asynchronous Receiver/Transmitter . UART is a chip that converts parallel input into serial output. It is usually inte...
1. Several nouns
ABI:
The specifications that an executable file must follow in order to run in a specific execution environment;
Separately generated relocatabl...[Details]
According to foreign media reports, Ford Motor has applied to the U.S. Patent and Social Security Administration (USPTO) for a patent for a remote vehicle control system that may be used in future ...[Details]
Whether it is an electric car or an ordinary fuel car, for the vast majority of car buyers, the final cost of use is what they care about most. For fuel cars, how to save fuel is what drivers care ...[Details]
In June 2014, the Ministry of Industry and Information Technology issued 4G FD-LTE licenses to China Unicom and China Telecom. Together with the 4G TD-LTE licenses issued to China Mobile, China Uni...[Details]
With the increasing number of new energy vehicles on the road, the deployment of supporting facilities for these vehicles has accelerated, and new energy vehicles have gradually entered the vision ...[Details]
In the electronics manufacturing industry, surface mount technology (SMT) placement machines are core equipment for production lines. However, with many different models available on the market, ch...[Details]
To improve the lateral active safety of intelligent connected vehicles, the identification and definition of unexpected functional safety scenarios for the EPS (Electronic Steering System) ...[Details]
MQTT Ethernet I/O modules primarily collect I/O port information and transmit data over the network. In addition to being a TCP server, Ethernet I/O modules can also function as TCP clients. Furthe...[Details]
The driving mode is not unfamiliar to vehicles. According to the driving mode of the vehicle, there are front-wheel drive, rear-wheel drive and even four-wheel drive. Four-wheel drive is a major se...[Details]
When American cartoonist Chester Gould sketched the watch on Dick Tracy's wrist, he had no idea that science fiction would become reality 70 years later. As a comic strip artist, Gould imagined fut...[Details]
Analog Devices held a third-quarter fiscal 2025 earnings conference call. Vincent T. Roche, CEO and Chairman of the Board, and Richard C. Puccio, Executive Vice President and Chief Financial Office...[Details]
I believe everyone has heard of memory. If your computer is slow, your experts may recommend upgrading it to a larger capacity. But what exactly is computer memory used for? Why does memory capacit...[Details]
As my country's industrialization continues to improve, environmental pollution is also facing tremendous pressure. In recent years, national environmental protection policies have become increasin...[Details]
As in-vehicle audio and video entertainment features become increasingly diverse, the demand for digital transmission of audio and video information is urgent. Traditional protocols such as IEEE 13...[Details]
Motor potting compound is a high-performance sealing material widely used for motor encapsulation and insulation. It is essential for motor protection and packaging. Its ideal moisture and water re...[Details]
Talking about work
京公网安备 11010802033920号
EEWORLD
