The MINMAX MA03 series is a new range of isolated 3W DC/DC-converter modules in a small SIP-package. There are 12 models available with 5V, 12V or
24VDC input. These products have a typical load regulation of 5.0% to 7.0% depending on model.
designer a new solution for many cost critical applications where the output voltage variation has to be kept in a certain limit under all load conditions.
The MA03 DC/DC converters are a compromise between a more expensive fully regulated converter and a non-regulated converter. They offer the
Model Selection Guide
Model
Number
Input
Voltage
(Range)
VDC
Output
Voltage
VDC
5
9
12
15
5
9
12
15
5
9
12
15
Output Current
Max.
mA
600
333
250
200
600
333
250
200
600
333
250
200
Min.
mA
12
6
4.5
3
12
6
4.5
3
12
6
4.5
3
Input Current
@Max. Load
mA(typ.)
723
689
701
686
298
285
284
281
152
147
146
147
@No Load
mA(typ.)
50
Load
Regulation
% (max.)
8
7
7
6
6
5
4.5
4
5.8
4.8
4.3
3.5
Max. capacitive
Load
µF
220
@Max. Load
%
83
87
85.5
87.5
84
87.5
88
89
82
85
85.5
85
Efficiency
(typ.)
MA03-05S05
MA03-05S09
MA03-05S12
MA03-05S15
MA03-12S05
MA03-12S09
MA03-12S12
MA03-12S15
MA03-24S05
MA03-24S09
MA03-24S12
MA03-24S15
5
(4.5 ~ 5.5)
12
(10.8 ~ 13.2)
24
(21.6 ~ 26.4)
40
220
30
220
Input Specifications
Parameter
Input Surge Voltage (1 sec. max.)
24V Input Models
5V Input Models
12V Input Models
5V Input Models
Model
Min.
-0.7
4.5
-0.7
Typ.
---
5
---
Max.
18
9
Unit
-0.7
---
Input Voltage Range
Reverse Polarity Input Current
Internal Filter Type
Internal Power Dissipation
24V Input Models
All Models
12V Input Models
21.6
---
10.8
24
---
12
26.4
0.5
13.2
A
mW
5.5
30
VDC
---
---
Internal Capacitor
700
Output Specifications
Line Regulation
Parameter
Load Regulation
For Vin Change of 1%
Io=20% to 100%
Conditions
Min.
---
Ripple & Noise (20MHz)
Temperature Coefficient
Short Circuit Protection
---
See Model Selection Guide
±0.01
60
±0.02
100
±1.01
Typ.
Max.
±1.2
Unit
%
---
mV
P-P
%/℃
0.5 Second Max.
E-mail:sales@minmax.com.tw
Tel:886-6-2923150
2013/01/23 REV:4
Page 1 of 4
DC/DC CONVERTER 3W,
SIP-Package
MA03 SERIES
General Specifications
I/O Isolation Voltage (rated)
I/O Isolation Resistance
Switching Frequency
I/O Isolation Capacitance
MTBF (calculated)
Safety Approvals(pending)
Parameter
60 Seconds
100KHz, 1V
500 VDC
Conditions
1000
---
Min.
Typ.
---
---
Max.
---
---
1000
---
VDC
M
pF
Unit
60
MIL-HDBK-217F@25℃, Ground Benign
2,000,000
---
CSA 60950-1 recognition,IEC/EN 60950-1(CB-scheme)
60
120
---
---
Hours
KHz
Input Fuse
2000mA Slow-Blow Type
5V Input Models
1000mA Slow-Blow Type
12V Input Models
500mA Slow-Blow Type
24V Input Models
Environmental Specifications
Case Temperature
Operating Ambient Temperature Range (See Power Derating Curve)
Storage Temperature Range
Humidity (non condensing)
Cooling
Parameter
Natural Convection
Conditions
Min.
-40
---
---
Max.
+100
95
+85
Unit
℃
℃
℃
% rel. H
℃
-50
Free-Air convection
---
+125
Lead Temperature (1.5mm from case for 10Sec.)
260
Power Derating Curve
Output Voltage Tolerance
+20%
+15%
+20%
+15%
Output Power (%)
Output Voltage(%)
+10%
Max.
+10%
+5%
Typ.
+5%
Vnom
Min.
Vnom
-5%
-5%
-10%
0%
20%
40%
60%
80%
-10%
100%
Output Load Current (%)
E-mail:sales@minmax.com.tw
Tel:886-6-2923150
2013/01/23 REV:4
Page 2 of 4
DC/DC CONVERTER 3W,
SIP-Package
MA03 SERIES
Notes
1
2
3
4
5
6
7
Specifications typical at Ta=+25℃, resistive load, nominal input voltage and rated output current unless otherwise noted.
Ripple & Noise measurement bandwidth is 0-20MHz.
These power converters require a minimum output loading to maintain specified regulation, operation under no-load conditions will not damage these modules;
however they may not meet all specifications listed.
All DC/DC converters should be externally fused at the front end for protection.
Other input and output voltage may be available, please contact factory.
That “natural convection” is about 20LFM but is not equal to still air (0 LFM).
Specifications are subject to change without notice.
Package Specifications
Mechanical Dimensions
19.5 [0.77]
Pin Connections
Pin
1
2
4
5
[0.13]
Function
+Vin
-Vin
0.5 [0.02]
10.2 [0.40]
0.5
[0.02]
2.4
[0.09]
[0.10]
2.54
5.08
[0.20]
2X2.54
[2X0.10]
18.5 [0.73]
7.6 [0.30]
Bottom View
1
2
4
5
6
3.2
6
No Pin
+Vout
-Vout
►
All dimensions in mm (inches)
►
Tolerance: X.X±0.25 (X.XX±0.01)
►
Pins ±0.05(±0.002)
Physical Characteristics
Case Size
:
Case Material
Pin Material
Weight
:
:
:
19.5x7.6x10.2mm (0.77x0.30x0.40 inches)
Non-Conductive Black Plastic (flammability to UL 94V-0 rated)
Alloy 42
2.2g
E-mail:sales@minmax.com.tw
Tel:886-6-2923150
2013/01/23 REV:4
Page 3 of 4
1.3 [0.05]
0.50
[0.02]
0.25 [0.01]
X.XX±0.13 ( X.XXX±0.005)
DC/DC CONVERTER 3W,
SIP-Package
Peak-to-Peak Output Noise Measurement Test
Use a Cout 0.33
µ
F ceramic capacitor. Scope measurement should be made by using a BNC socket, measurement bandwidth is 0-20 MHz. Position the load
between 50 mm and 75 mm from the DC/DC Converter.
+Vin
Single Output
DC / DC
Converter
-Vin
-Out
+Out
Copper Strip
Cout
Copper Strip
Scope
Resistive
Load
MA03 SERIES
Test Setup
Technical Notes
Maximum Capacitive Load
The MA03 series has limitation of maximum connected capacitance at the output. The power module may be operated in current limiting mode during start-up,
affecting the ramp-up and the startup time. For optimum performance we recommend 220
µ
F maximum capacitive load for devices. The maximum capacitance can be
found in the data sheet.
Input Source Impedance
The power module should be connected to a low ac-impedance input source. Highly inductive source impedances can affect the stability of the power module. In
applications where power is supplied over long lines and output loading is high, it may be necessary to use a capacitor at the input to ensure startup.
Capacitor mounted close to the power module helps ensure stability of the unit, it is commended to use a good quality low Equivalent Series Resistance (ESR < 1.0
at 100 KHz) capacitor of a 2.2
µ
F for the 5V input devices, a 1.0
µ
F for the 12V input devices and a 0.47
µ
F for the 24V devices.
+
DC Power
Source
-
+
Cin
-Vin
-Out
+Vin
DC / DC
Converter
+Out
Load
Output Ripple Reduction
A good quality low ESR capacitor placed as close as practicable across the load will give the best ripple and noise performance. To reduce output ripple, it is
recommended to use 1.0
µ
F capacitors at the output.
+
DC Power
Source
-
-Vin
+Vin
Single Output
DC / DC
Converter
-Out
+Out
Cout
Load
Thermal Considerations
Many conditions affect the thermal performance of the power module, such as orientation, airflow over the module and board spacing. To avoid exceeding the
maximum temperature rating of the components inside the power module, the case temperature must be kept below 100℃. The derating curves are determined from
measurements obtained in a test setup.
Position of air velocity
probe and thermocouple
15mm / 0.6in
50mm / 2in
Air Flow
DUT
18, Sin Sin Road, An-Ping Industrial District, Tainan 702, Taiwan
After driving the OLED screen last time, I was thinking one night, if the screen is also on at night, it will be a night light (I can't sleep at night with light). So this time I added a photoresistor...
As the title: 1. What does BANK mean in ARM? Is it a unit? 2. The description of BIT3 and BIT19 of the MSC0 register in PXA270 both define the number of bits of my FLASH connection. However, my BSP se...
AT+CREG? +CREG: 0,5 OK At first it was 0,2, which means it is searching for a network. But after a while it returned 0,5. I read the explanation and it said it was in roaming state, but my card is a l...
William I, King Frederick of Prussia, known as the "Soldier King", was later crowned as the German Emperor by the monarchs of the German states in the Hall of Mirrors in Versailles, Paris, France. He ...
TinyGo is a Go compiler for microcontrollers that uses WebAssembly (WASM) and command-line tools. It reuses the Go language tools and libraries used with LLVM to compile programs written in the Go pro...
ROM_SysCtlClockSet(), ROM_GPIOPinTypeGPIOInput(), what does the ROM_ in front of these functions mean? Why is there no need to add ROM_ in front of them sometimes? :Mad:...
From being a global leader to losing the market, Korean battery manufacturers have always wanted to regain the lost market and dignity, but facing Chinese battery manufacturers represented by CAT...[Details]
If the ultimate form of a car is a silicon-based life form, then in
the field of
intelligent driving
, it has gradually taken on the appearance of a "veteran driver." In
the field of
the ...[Details]
Reflow soldering is a critical process in electronics assembly production, and the cleanliness of the reflow oven has a direct impact on product quality. Dust and residue accumulation within the ov...[Details]
EtherCAT (Ethernet for Control Automation Technology) is a real-time industrial fieldbus communication protocol based on an Ethernet-based development framework. EtherCAT is one of the fastest indu...[Details]
Is electromagnetic radiation from electric vehicles harmful to the human body? Recently, the issue of electromagnetic radiation from electric vehicles has garnered widespread attention. However, pu...[Details]
Long ago, the lifespan of cars in my country was 15 years. Once a car reached 15 years old, it was forced to be scrapped. However, the policy was later changed. As long as the car does not exceed 6...[Details]
For healthcare professionals, accurate diagnosis and treatment are crucial for a clear picture of a person's health. However, healthcare professionals often rely on tests at medical facilities, cli...[Details]
With the rapid adoption of smart electric vehicles, automotive chips are evolving from auxiliary control units to the foundation of the entire vehicle's intelligence. Their applications extend from...[Details]
Gross profit margin jumped from 13.6% in the first half of last year to 25.9%, almost doubling year-on-year.
On August 21, RoboSense released its interim performance report, in which the...[Details]
Robotics
has become
LiDAR
's "second growth curve."
While LiDAR was still battling with its "pure vision" rivals in the automotive field, another field ignited the demand f...[Details]
On August 22, the National Energy Administration released the latest data, showing that by the end of July 2025, China's total number of electric vehicle charging infrastructure will reach 16.696 m...[Details]
On August 22, South Korean media Nate reported on the 20th local time that Samsung Electronics is introducing Hyper Cell technology into its most advanced 2nm process technology, striving to improv...[Details]
The all-new MG4 was recently officially announced on the Ministry of Industry and Information Technology's (MIIT) new vehicle announcement. The all-new MG4's semi-solid-state battery version addres...[Details]
introduction
As “energy conservation and emission reduction” has become an indicator of the National Economic Development Outline of the 11th Five-Year Plan, people’s awareness of green enviro...[Details]
In the scorching summer, electric fans are a must-have for cooling down people's homes. However, I believe most people have encountered this situation: the fan is plugged in, the switch is pressed,...[Details]
Domestic Chip Exchange
京公网安备 11010802033920号
EEWORLD
