EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-NI2SA3845

Description
Transponder, SC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-NI2SA3845 Overview

Transponder, SC/UPC Connector,

PH1-NI2SA3845 Parametric

Parameter NameAttribute value
MakerJDS Uniphase Corporation ( VIAVI )
Reach Compliance Codeunknown
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body width56.1 mm
body height13.2 mm
Body length or diameter76.5 mm
Communication standardsGR-253, OC-192, SONET
Connection TypeSC/UPC CONNECTOR
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1553 nm
Nominal optical power output1.122 mW
minimum return loss-27 dB
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
THAT4320 low voltage dynamic processing circuit for wireless products
THAT's Analog Engine IC THAT4320 for advanced wireless microphones has unmatched performance in audio wireless transmission compression, expansion, noise suppression, dynamic range, noise and distorti...
THAT音频 Mobile and portable
[Sharing] Forum usage tips and methods
Since this is a comprehensive technology area, can you share some tips and methods used in the forum? If you think it is good and convenient, even if it is just a light click, I will take out my chip ...
Sur Integrated technical exchanges
An important operation about converting Altium Designer to pads
[i=s]This post was last edited by spacexplorer on 2015-5-11 16:47[/i] I worked overtime to draw a board a few days ago. The PCB frame was transferred from AD. There were always problems when it came t...
spacexplorer PCB Design
Chapter 7 Bulk Equipment
Written by Ogawa Studio, this book is written for the LM3S USB chip. The uploaded ones are all drafts and have not been revised . There may be many shortcomings. I hope netizens will forgive me! QQ:26...
paulhyde Microcontroller MCU
[Repost] AVR driver floppy drive motor program
/*Use mega32 three port lines to drive the floppy drive motor. PA2 connects to LB1833 ENA1\2 pin; PA1 connects to LB1833 IN1 pin; PA0 connects to LB1833 IN2 pin. **************************************...
黑衣人 Microchip MCU
Regarding the connection number calculation problem
The controller and communication module in the AB control system each have their own upper limit on the number of connections. For example, ControlLogix has an upper limit of 250 connections, 1756-CNB...
eeleader Industrial Control Electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2868  646  2828  375  2545  58  14  57  8  52 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号