EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-NLHLA428N

Description
Transponder, LC/SPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerLumentum Operations LLC
Download Datasheet Parametric View All

PH1-NLHLA428N Overview

Transponder, LC/SPC Connector,

PH1-NLHLA428N Parametric

Parameter NameAttribute value
MakerLumentum Operations LLC
Reach Compliance Codecompliant
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body width56.1 mm
body height13.2 mm
Body length or diameter76.5 mm
Communication standardsOC-192, SONET
Connection TypeLC/SPC CONNECTOR
Emitter/Detector TypeAVALANCHE PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1562 nm
Nominal optical power output2.511 mW
minimum return loss-27 dB
Sensitivity-24 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Please help, can I move the FAT16 partition on the SD card?
I have a 16G card. Is there any way to move the partition that stores the Device Tree file to the end of the SD card? I have tried several partitioning software but none of them worked. If I copy the ...
wjdb3 FPGA/CPLD
MSP430 clock system problem
[size=4] The clock problem of MSP430 has always been vague, and I always forget it, so I decided to write this article to help me remember. The following content is all referenced to online materials ...
灞波儿奔 Microcontroller MCU
Hybrid Electric Vehicle Control System
Modern computer technology and automatic control technology with computers as the core are widely used in HEV. Various intelligent control systems, including adaptive control technology (MRAC), fuzzy ...
zzloveff Automotive Electronics
Internal functions of MSP430
Internal functions: some special functions provided by the compiler for the target CPU, as well as commonly used functions that are highly optimized after assembly. The internal functions provided by ...
Jacktang Microcontroller MCU
Has anyone used 6713? Can anyone help?
RT, can the ECLKIN pin of 6713 be left unconnected? Also, any experts who have used cadence, please help me with any questions~:congratulate:...
juring DSP and ARM Processors
The more "flirty" serpentine traces on a PCB, the more "advanced" it is?
The serpentine line is a routing method often used in the PCB wiring process. Its main purpose is to adjust the delay and meet the system timing design requirements. However, every PCB design engineer...
mwkjhl PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1728  2498  2724  2415  951  35  51  55  49  20 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号