EEWORLDEEWORLDEEWORLD

Part Number

Search

PE1145B-FREQ

Description
PECL Output Clock Oscillator, 1.5MHz Min, 250MHz Max, LEADLESS PACKAGE-6
CategoryPassive components    oscillator   
File Size71KB,4 Pages
ManufacturerPletronics
Download Datasheet Parametric View All

PE1145B-FREQ Overview

PECL Output Clock Oscillator, 1.5MHz Min, 250MHz Max, LEADLESS PACKAGE-6

PE1145B-FREQ Parametric

Parameter NameAttribute value
MakerPletronics
Reach Compliance Codeunknown
Other featuresTAPE; TUBE; OUTPUT ENABLE/DISABLE FUNCTION
maximum descent time1 ns
Frequency Adjustment - MechanicalNO
frequency stability50%
Manufacturer's serial numberPE1145B
Installation featuresSURFACE MOUNT
Maximum operating frequency250 MHz
Minimum operating frequency1.5 MHz
Maximum operating temperature80 °C
Minimum operating temperature
Oscillator typePECL
physical size14.23mm x 10.16mm x 3.17mm
longest rise time1 ns
Maximum supply voltage3.465 V
Minimum supply voltage3.135 V
Nominal supply voltage3.3 V
surface mountYES
maximum symmetry45/55 %
Pl tronics, Inc.
.
19013 36th Ave. W, Suite H Lynnwood, WA 98036 USA
Manufacturer of High Quality Frequency Control Products
Differential PECL Series
Differential PECL Output, Some with Enable/ Disable Function
Available in 9 Different Package/Configurations, See Next Pages
Standard Specifications
Overall Frequency Stability
Operating Temperature Range
Storage Temperature Range
Supply Voltage (Vcc)
Supply Current (Icc)
Output High Level
± 50 PPM, ± 25 PPM, ± 20 PPM over Operating Temperature Range
0 to +80°C is standard, but can be extended to - 40 to +85°C
- 55 to +125°C
3.3 volts ± 5% standard, but 5.0 volts or 2.5 volts also available. See Test Cirucit 5.
< 250 MHz = 90 mA maximum, 250 MHz and above = 100 mA maximum
2.275 V minimum referenced to Ground, Vcc = 3.300V,
0.975 V minimum referenced to termination voltage,
- 1.025 V minimum referenced to Vcc
1.680 V maximum referenced to Ground, Vcc = 3.300V,
0.380 V maximum referenced to termination voltage,
- 1.620 V maximum referenced to Vcc
45/55% referenced to 50% of amplitude
1.0 nS maximum when Vth is 10% and 90% of waveform
1 pS RMS maximum measured
from 12 kHz to 20 MHz from Fnominal
50 kohm minimum to Vcc
0.3 Vcc maximum referenced to Ground
0.7 Vcc minumum referenced to Ground
Output Low Level
Output Symmetry
Output Rise & Fall (Tr & Tf)
Jitter
E/D Internal Pullup
V disable
V enable
PE7745D only Output Enable / Disable
High Level Input Current
-20 uA maximum at Enable / Disable Pin = 0.7 Vcc
Low Level Input Current
-200 uA maximum at Enable / Disable Pin = 0 V
Output Enable Time
200 nS maximum at output enable or 1 mS maximum at output enabled and stable
Output Disable Time
200 nS maximum at output disable
Vcc Supply Current disabled < 1 mA. Both outputs are high impedance when disabled.
All other models Output Enable/Disable (E/D)
Output Enable Time
100 nS maximum
Output Disable Time
100 nS maximum
When Disabled
Q Output = Logic Low, QN Output = Logic High. Both Outputs are active
Note 1:
PECL and ECL are identical circuits.
ECL has the most positive pin as ground and is ideally terminated by 50 ohms to - 2.00 V
PECL has the most negative pin as ground and is ideally terminated by 50 ohms to the most (positive voltage less 2.00 V)
Mechanical: See Next Pages
D Package
J Package Replacement
B Package
M Package
Mar 2004
Pl tronics, Inc.
(425) 776 -1880, Fax: (425) 776-2760, ple-sales@pletronics.com, www.pletronics.com
1
PECL, LVDS, OCXO
Page 1 - 7
nand driver in bsp of 6410???
The nand used in my 6410 is K9G8G08, and the size of a block is 0x40000, but the corresponding model block size defined by the nand driver in the bsp is 0x20000, which causes abnormal operation of nan...
rcsun Embedded System
How to realize an accurate signal generator using only a single chip microcomputer
[i=s]This post was last edited by paulhyde on 2014-9-15 03:50[/i]I am currently working on a task to build a function signal generator based on a microcontroller. I have not found a good method, so pl...
369432939 Electronics Design Contest
How to use 2812 to achieve fixed off time control
I want to use 2812 to achieve fixed off-time control of boost PFC. I compare the AC side current output with the given inductor current envelope, and finally query the GPIO output pulse according to t...
Blacklou DSP and ARM Processors
Moderator~~ Help with chip encryption and decryption issues~
Problem description:I use the STM32 STLINK UTILITY burning software from the ST official website. After burning the program, I enable output protection, so that the program cannot be read out. When I ...
lgj99988 stm32/stm8
About HELPER2416 product warranty
[i=s]This post was last edited by spacexplorer on 2014-7-5 17:39[/i] We have tested all the development boards sent by HELPER2416, but there are always omissions and violent couriers. We provide a 1-y...
spacexplorer Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2533  558  1022  535  2323  52  12  21  11  47 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号