EEWORLDEEWORLDEEWORLD

Part Number

Search

BU-65142-840Q

Description
Micro Peripheral IC
CategoryThe embedded processor and controller    Microcontrollers and processors   
File Size219KB,24 Pages
ManufacturerData Device Corporation
Download Datasheet Parametric View All

BU-65142-840Q Overview

Micro Peripheral IC

BU-65142-840Q Parametric

Parameter NameAttribute value
MakerData Device Corporation
package instruction,
Reach Compliance Codecompliant
BU-65142 and BUS-65142 SERIES
MIL-STD-1553 DUAL REDUNDANT
REMOTE TERMINAL HYBRID
DESCRIPTION
The BUS-65142 Series is a com-
plete dual redundant MIL-STD-
1553 Remote Terminal Unit (RTU)
packaged in a small 1.9" x 2.1"
hybrid. The device is based upon
two DDC custom ICs, which
includes two monolithic bi-polar low
power transceivers and one CMOS
protocol containing data buffers
and timing control logic. It supports
all 13 mode codes for dual redun-
dant operation, any combinaion of
which can be illegalized.
Parallel data transfers are accom-
plished with a DMA type handshak-
ing, compatible with most CPU
types. Data transfers to/from mem-
ory are simplified by the latched
command word and word count out-
puts.
Error detection and recovery are
enhanced by BUS-65142 Series
special features. A 14-bit built-in-
test word register stores RTU infor-
mation, and sends it to the Bus
Controller in response to the Mode
Command Transmit Bit Word. The
BUS-65142 Series performs contin-
uous on-line wraparound self-test,
and provides four error flags to the
host CPU. Inputs are provided for
host CPU control of 6 bits of the
RTU Status Word.
Its small hermetic package, -55°C
to +125°C operating temperature
range, and complete RTU operation
make the BUS-65142 ideal for most
MIL-STD-1553 applications requir-
ing hardware or microprocessor
subsystems.
FEATURES
Complete Intergrated Remote
Terminal Including:
–Dual Low-Power Transceivers
–Complete RT Protocol
Direct Interface to Systems With
No Processor
Radiation Tolerant Version
Available
Space Qualified Version
Available
High Reliability Screening
Available
DATA
BUS A
TRANSCEIVER
ENCODER/
DECODER
BIT
PROCESSOR
BUFFER
DB0-DB15
BUF ENA
DTREQ
DTGRT
DTACK
DTSTR
R/W
WATCHDOG
TIMEOUT
TRANSFER
CONTROLS
DATA
BUS B
TRANSCEIVER
ENCODER/
DECODER
BIT
PROCESSOR
CURRENT
WORD
COUNTER
PROTOCOL
SEQUENCER
AND
CONTROL
LOGIC
M
U
X
A0-A4
A5-A10
DAT/CMD
ILL CMD (ME)
SS REQ
ADBC
RT FLAG
SS BUSY
SS FLAG
MESS ERR
RT FAIL
HS FAIL
RTADD ERR
NBGT
INCMD
BITEN
STATEN
GBR
COMMAND
LATCH
RT ADDRESS
+
PARITY
STATUS
REGISTER
16 MHz CLOCK
ERROR FLAGS
TIMING FLAGS
DDC CUSTOM CHIP
FIGURE 1. BUS-65142 SERIES BLOCK DIAGRAM
©
1988, 1999 Data Device Corporation
Can anyone tell me in plain language what the kobject and sys under the driver are used for?
Can anyone tell me in layman's terms what kobject and sys are used for in the driver? Thanks!...
weilwo Embedded System
Frequency division of analog signals
I'd like to ask for a solution. If the analog signal frequency is 27Mhz, after being rectified into a square wave through other circuits, it is edge-triggered by a microcontroller to test the frequenc...
呜呼哀哉 Analog electronics
C2000-GNAG Operation and Use
I recently bought a multi-channel programmer (model: C2000-GNAG), but it doesn't work when I get it back. What's the reason?...
学习着 Microcontroller MCU
HelloM3 Application Notes--TI M3 Tempest C1 Version Programming Instructions
For the Tempest series C1 version chips produced after May 2010 , a reset patch is applied to the first 4K internal Flash , so the code start address of all user programs needs to be changed to 0x1000...
jkhu Microcontroller MCU
Is anyone debugging SPI communication under S3C6400? Mine is acting strangely. I set it to receive mode and haven't connected the data source yet, but the SPI interrupt is constantly triggered. I don't know why? Is it interference? !
Is there anyone debugging SPI communication under S3C6400? Why is mine so strange? When it is set to receive mode and the data source is not connected, the SPI interrupt will be triggered continuously...
yejing2008 Embedded System
printk() problem, urgent solution!
Dear experts: I have cross-compiled a driver module and can now successfully load it on a development board. This development board is a MIPS processor and runs the Linux system. However, my program h...
chongxinzhenzuo Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1291  2442  256  1194  2632  26  50  6  25  53 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号