EEWORLDEEWORLDEEWORLD

Part Number

Search

DBM9W4SNMBBFR163

Description
D Subminiature Connector, 9 Contact(s), Female, Solder Terminal, Receptacle,
CategoryThe connector    The connector   
File Size50KB,1 Pages
ManufacturerITT
Websitehttp://www.ittcannon.com/
Download Datasheet Parametric View All

DBM9W4SNMBBFR163 Overview

D Subminiature Connector, 9 Contact(s), Female, Solder Terminal, Receptacle,

DBM9W4SNMBBFR163 Parametric

Parameter NameAttribute value
MakerITT
Reach Compliance Codecompliant
Body/casing typeRECEPTACLE
Connector typeD SUBMINIATURE CONNECTOR
Contact point genderFEMALE
DIN complianceNO
empty shellNO
Filter functionNO
IEC complianceNO
insulator materialPLASTIC
MIL complianceNO
Manufacturer's serial numberDBM
Plug informationMULTIPLE MATING PARTS AVAILABLE
Mixed contactsYES
Installation typeBOARD
Shell surfaceTIN
Shell materialCOPPER ALLOY
Housing size3/B
Termination typeSOLDER
Total number of contacts9
UL Flammability Code94V-0
Planning to port Android to OMAP3530
Last year, I bought a 3530 board in 2012 but never played with it. The built-in data included an Android uboot and kernel. It can run. At that time, I could hardly find any porting information on the ...
astwyg Embedded System
[Decryption 03] Wireless remote control tank DIY based on 51 single chip microcomputer motor control circuit
[font=微软雅黑][size=3] Continue decrypting... Last time we have had a general understanding of the use of the "H-bridge" chip L9110. This time we will explain how to use this chip to control the rotation...
@ZiShi DIY/Open Source Hardware
STC89C52 minimum system problem
The author built a minimum system with STC89C51 as shown below. The power supply uses the chip LM2940 to convert the 8V voltage into 5V and then power the microcontroller, and P2.7 is used to control ...
五加一等于六 51mcu
I also want to ask about CAN.
I did a CAN test on STM32F103VBT6, using TI's VP230 driver. The voltage on pin 230 is correct. The high-speed mode and slope control mode are not working. The program is fine because the same program ...
xuyangsuccess stm32/stm8
Can this diagram be used in this way?
Because the IO of the microcontroller is 5V, and the sensor signal is 24V, I hope that the sensor can cut off the signal of the optocoupler while the IO controls the optocoupler. Because the IO of the...
sky999 PCB Design
About downloading programs using emulator
Question: When downloading the program using JT-LINK's SW method, what are the requirements for the high and low levels of the BOOT0 and BOOT1 pins?...
深圳小花 MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 106  2386  2809  520  138  3  49  57  11  58 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号