EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-FLHFC2565

Description
Transponder, 10660Mbps(Tx), 10660Mbps(Rx), FC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerLumentum Operations LLC
Download Datasheet Parametric View All

PH1-FLHFC2565 Overview

Transponder, 10660Mbps(Tx), 10660Mbps(Rx), FC/UPC Connector,

PH1-FLHFC2565 Parametric

Parameter NameAttribute value
MakerLumentum Operations LLC
Reach Compliance Codecompliant
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Connection TypeFC/UPC CONNECTOR
Data rate (receive)10660 Mbps
Data rate (send)10660 Mbps
Emitter/Detector TypeAVALANCHE PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1528 nm
Nominal optical power output2.511 mW
minimum return loss-27 dB
Sensitivity-24 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
How to call Sqlce3.5 database with EVC4.0? Urgent ====================================
Hello, I developed an MFC program with EVC4.0 and run it on Wince 5.0. I used to use the sdf database of Sqlce3.0. Now after upgrading the database to 3.5, I can't connect to the database. My connecti...
daqiic Embedded System
How to connect the battery to power beaglebone black
The current status is this: According to the manual, I connected the 3.3V voltage to tp5 of bbb and the ground to tp8. Through measurement, I can find that sys1 and sys2 of tps65217c have 3.3V output,...
shuzijiqun DSP and ARM Processors
So many mistakes, it's scary.
Build Complete, 1686 Errors, 57 Warnings, 0 Remarks.All of this type,error: symbol _QY_Timer is defined multiple times: C:\CCStudio_v3.3\MyProjects\svg\svg\Debug\Fault.obj and C:\CCStudio_v3.3\MyProje...
cumtliyan Microcontroller MCU
I would like to ask for your help in designing a digital clock based on multisim2001! Thank you very much!
I am going to do my graduation project, and I would like to ask experienced experts to help me, thank you! It would be best if I have a paper and circuit diagram!...
vv0147 Embedded System
How is the 0-10V interface circuit for intelligent dimming usually implemented?
How is the 0-10V interface circuit for intelligent dimming usually implemented? How competitive is this GP8101 solution? For your reference...
zjqmyron Analog electronics
Problems after DSP28335 program is burned into flash
[size=4]After the DSP28335 program is burned into the flash, it shows that the burning is successful and there is no problem running online. After powering off and then powering on again, it feels tha...
liuqiang Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2325  2222  617  2315  668  47  45  13  14  12 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号