EEWORLDEEWORLDEEWORLD

Part Number

Search

WLS1A03AQ4BT3

Description
Limitless™ Single Switch Adapter
File Size2MB,47 Pages
ManufacturerHoneywell
Websitehttp://www.ssec.honeywell.com/
Download Datasheet View All

WLS1A03AQ4BT3 Overview

Limitless™ Single Switch Adapter

Installation and Technical Manual for the
Limitless™ Series WDRR Receiver
50063987
ISSUE 5
WARNING
DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
PERSONAL INJURY
The WDRR must be installed in accordance with the
requirements specified in this document in order to comply
with the specific Country Communication Agency
requirements. (i.e. FCC, IC, ETSI, ACMA, etc.) See
Section 3 as it requires choosing the correct Country Use
Code and thus allowable antenna and/or cable usage.
WARNING
WARNING
Honeywell does not recommend using devices for critical
control applications where there is, or may be, a single point
of failure or where single points of failure may result in an
unsafe condition. It is up to the end-user to weigh the risks
and benefits to determine if the products are appropriate for
the application based on security, safety and performance.
Additionally, it is up to the end-user to ensure that the
control strategy results in a safe operating condition if any
crucial segment of the control solution fails.
Honeywell customers assume full responsibility for learning
and meeting the required Declaration of Conformity,
Regulations, Guidelines, etc. for each country in their
distribution market.
Failure to comply with these instructions could result in
death or serious injury.
Pay attention to ESD discharge at dc-in port.
WARNING
WARNING
Korean Communication Commission does not allow this
equipment to be used for rescue service.
Anatel states that this device works as a secondary
function model. It may not be used as a protection device
against harmful interference. It cannot cause interference
with systems that are running as primary function.
WARNING
CAUTION
* Power to the WDRR should not be applied during
installation of antenna as damage could occur to the
WDRR electronics.
WARNING
To satisfy FCC RF exposure requirements for mobile
transmitting devices, a separation distance of 20 cm or
more should be maintained between the antenna of this
device and persons during device operation To ensure
compliance, operation at closer than this distance is not
recommended. The antenna used for this transmission
must not be co-located in conjunction with any other
antenna or transmitter.
Failure to comply with these instructions could result in
death or serious injury.
RF EXPOSURE
CAUTION
* The WDRR receiver offers optimal performance when
paired with Limitless™ inputs that have a firmware
version of 7170 or a greater number (i.e., FW7170 will be
printed on the Limitless™ input label). If the Limitless™
input is paired with older firmware (FW7170 or a lesser
number), the WDRR may exhibit delayed responses
under simultaneous operation.
Sensing and Productivity Solutions
MIC circuit principle
FET:(field effect tube[/size][/font][/color][font=宋体][size=12pt]field effect tube[/size][/font][color=black][size=12pt][font=Times New Roman]) is the main component of MIC, which plays the role of imp...
simonprince Analog electronics
[Xilinx Free Training] Try Spartan-6 Embedded Kit for Yourself, Sign Up Now!
[font=Times New Roman][/font] [font=Times New Roman][/font] [font=Times New Roman]From now on - the end of 2010, EEWORLD will carry Xilinx Spartan-6[font=宋体] embedded kit worth $995 to launch a one-ye...
EEWORLD社区 FPGA/CPLD
Hello everyone, I am a newbie on this site. I would like to ask some questions about C language programming.
Hello everyone! I am a student who has just entered college. My major is Internet of Things Engineering. I chose this major because I have a great interest in computer languages and embedded systems. ...
beautifulul Programming Basics
As shown in the picture: Why is my AD10 not displayed? How can I make it display in the menu bar?
[img=110,0]https://bbs.eeworld.com.cn/forum.php?mod=image&aid=197637&size=300x300&key=6591e809ad3d6519&nocache=yes&type=fixnone[/img]Why is my AD10 not displayed? How can I make it display in the menu...
hu柏拉图的永恒 PCB Design
About Bluetooth file transfer ~!
Can any experts please tell me how to write the program of Bluetooth obex server?...
a7016 Embedded System
JEDEC failure rate estimates
JEDEC failure rate estimates...
1234 Test/Measurement

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2727  63  2679  334  287  55  2  54  7  6 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号