stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
PERSONAL INJURY
•
The WDRR must be installed in accordance with the
requirements specified in this document in order to comply
with the specific Country Communication Agency
requirements. (i.e. FCC, IC, ETSI, ACMA, etc.) See
Section 3 as it requires choosing the correct Country Use
Code and thus allowable antenna and/or cable usage.
WARNING
WARNING
Honeywell does not recommend using devices for critical
control applications where there is, or may be, a single point
of failure or where single points of failure may result in an
unsafe condition. It is up to the end-user to weigh the risks
and benefits to determine if the products are appropriate for
the application based on security, safety and performance.
Additionally, it is up to the end-user to ensure that the
control strategy results in a safe operating condition if any
crucial segment of the control solution fails.
Honeywell customers assume full responsibility for learning
and meeting the required Declaration of Conformity,
Regulations, Guidelines, etc. for each country in their
distribution market.
Failure to comply with these instructions could result in
death or serious injury.
•
Pay attention to ESD discharge at dc-in port.
WARNING
WARNING
•
Korean Communication Commission does not allow this
equipment to be used for rescue service.
•
Anatel states that this device works as a secondary
function model. It may not be used as a protection device
against harmful interference. It cannot cause interference
with systems that are running as primary function.
WARNING
CAUTION
* Power to the WDRR should not be applied during
installation of antenna as damage could occur to the
WDRR electronics.
WARNING
•
To satisfy FCC RF exposure requirements for mobile
transmitting devices, a separation distance of 20 cm or
more should be maintained between the antenna of this
device and persons during device operation To ensure
compliance, operation at closer than this distance is not
recommended. The antenna used for this transmission
must not be co-located in conjunction with any other
antenna or transmitter.
Failure to comply with these instructions could result in
death or serious injury.
RF EXPOSURE
CAUTION
* The WDRR receiver offers optimal performance when
paired with Limitless™ inputs that have a firmware
version of 7170 or a greater number (i.e., FW7170 will be
printed on the Limitless™ input label). If the Limitless™
input is paired with older firmware (FW7170 or a lesser
number), the WDRR may exhibit delayed responses
under simultaneous operation.
Sensing and Productivity Solutions
Limitless™
WDRR Receiver
T
ABLE OF
C
ONTENTS
Issue 5
50063987
TABLE OF CONTENTS
............................................................................................................................................................ II
LIST OF FIGURES
.................................................................................................................................................................... VI
I saw the mouser activity on the forum, and I remembered the TI board I had been thinking about, that is, the F28377D board! This board costs more than 1,200 yuan on mouser, cough cough... {:1_137:} I...
Recently, my project needs a microprocessor with an I2S interface. My boss asked me to look at the MSP430 series, but I couldn't find one after searching for a long time. Is there any MSP430 series mi...
1 - Unable to detect the target system Before debugging, please connect the target board and then use the debugging software to detect the target system. If the target system cannot be detected, pleas...
A Primax mouse, which is still very useful after many years of use, but unfortunately it is mechanical. Obviously, in the era of optical mice, this kind of mouse should have been discarded long ago, b...
[table=98%] [tr][td][b]9. netstat - Displays open ports and connections[/b][align=left]It is a tool used by Linux administrators to display various network information, such as what ports are open and...
Microcontrollers (MCUs), which are widely used in automotive electronics, are rapidly facing time and cost pressures. The main advantage of using MCUs has always been to create high-level system in...[Details]
1. Introduction
This design was made for participating in an electronic design competition. It effectively solved the problem of the operation and control of an electric car on a seesaw. The s...[Details]
With the advent of increasingly powerful processors, image sensors, memory, and other semiconductor devices, as well as the algorithms that enable them, computer vision can be implemented in a wide...[Details]
Analog engineers have traditionally struggled with complexity when designing power supplies that required multiple outputs, dynamic load sharing, hot-swap, or extensive fault-handling capabilities....[Details]
In recent years, the market for mobile/portable devices such as smartphones and laptops has continued to grow rapidly. While these products continue to integrate more new features to enhance the ...[Details]
1. Introduction
Light control circuit plays a vital role in urban street lamps or corridor lighting. With light control circuit, the lights can be automatically turned on and off according to ...[Details]
The reason for the light decay of white LEDs: the decline of phosphor performance
So far, the rapid decline of the luminous performance of white light LEDs, especially low-power white light LE...[Details]
With the continuous improvement of the requirements of intelligent building security systems and the continuous improvement of people's safety awareness, indoor anti-theft has gradually attracted peop...[Details]
From the PIC16F946 datasheet, we know that there are two ways to write values to the LCD for display:
1. Directly write the value to LCDDATA1~LCDDATA23
2. Use disconnect t...[Details]
As people's requirements for safety and comfort in the process of driving cars continue to increase, automotive radars are widely used in the car's adaptive cruise system, collision avoidance syste...[Details]
LED technology has made rapid progress, and improvements in chip design and materials have promoted the development of brighter and more durable light sources, and the scope of light source applica...[Details]
With the rapid development of wireless
digital communication
, more challenges have been raised for integrated circuit design and testing. In the product design stage, in order to ensure
t...[Details]
The DisplayPort interface standard is approved by the Video Electronics Standards Association (VESA) to provide an open, scalable standard for the entire industry. The development of DisplayPort ca...[Details]
The launch of Shenzhou IX is imminent, and Tiangong is welcoming visitors again. Yesterday, Professor Fu Qiang, Vice President of the Institute of Science and Industrial Technology of Harbin Instit...[Details]
This article discusses the six design steps of LED lighting system design in detail: (1) determine the lighting requirements; (2) determine the design goals and estimate the optics; (3) the efficie...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
