LB1935FA is IC with forward/reverse motor drive 2-channel in which low saturation voltage and low voltage operation
possible. Its small sized package is optimal for 2 phase excitation drive of 2 phase bipolar stepping motors for various
portable devices such as digital still cameras.
Features
• Low saturation voltage, VO (sat) = 0.3V typ at IO = 150mA
• Built-in shoot-through current protection circuit
• No standby current consumption (or zero)
• Built-in thermal shutdown circuit
• Micro10 small-sized package
Absolute Maximum Ratings
at Ta = 25°C
Parameter
Maximum power source voltage
Applied output voltage
Applied input voltage
GND Pin outflow current
Allowable power dissipation
Operating temperature
Storage temperature
Symbol
VCC max
VOUT max
VIN max
I GND
Pd max
Topr
Tstg
OUT1, OUT2, OUT3, OUT4 pin
ENA, IN1, IN2 pin
Per channel
With substrate*
Conditions
Ratings
-0.3 to +8.0
VCC+VSF
-0.3 to +8.0
400
400
-20 to +75
-40 to +150
Unit
V
V
V
mA
mW
°C
°C
* Specified substrate: 20.0mm×10.0mm×0.8mm, paper phenol
Caution 1) Absolute maximum ratings represent the value which cannot be exceeded for any length of time.
Caution 2) Even when the device is used within the range of absolute maximum ratings, as a result of continuous usage under high temperature, high current,
high voltage, or drastic temperature change, the reliability of the IC may be degraded. Please contact us for the further details.
Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to
"standard application", intended for the use as general electronics equipment. The products mentioned herein
shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life,
aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system,
safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives
in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any
guarantee thereof. If you should intend to use our products for new introduction or other application different
from current conditions on the usage of automotive device, communication device, office equipment, industrial
equipment etc. , please consult with us about usage condition (temperature, operation time etc.) prior to the
intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely
responsible for the use.
Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate
the performance, characteristics, and functions of the described products in the independent state, and are not
guarantees of the performance, characteristics, and functions of the described products as mounted in the
customer
'
s products or equipment. To verify symptoms and states that cannot be evaluated in an independent
device, the customer should always evaluate and test devices mounted in the customer
'
s products or
equipment.
52312 SY 20120514-S00001 No.A2060-1/4
LB1935FA
Allowable Operating Range
at Ta = 25°C
Parameter
Source voltage
Input high level voltage
Input low level voltage
Symbol
VCC
VIH
VIL
ENA, IN1, IN2 pin
ENA, IN1, IN2 pin
Conditions
Ratings
2.2 to 7.5
1.8 to 7.5
-0.3 to +0.7
Unit
V
V
V
Electric Characteristics
at Ta = 25°C, VCC = 3.3V
Ratings
Parameter
Power source current
Symbol
ICC0
ICC1
Output saturation voltage
VOUT1
VOUT2
Input current
IIN
IENA
Spark killer diode
Reverse current
Forward voltage
IS(leak)
VSF
IOUT = 200mA
1
1.7
μA
V
Conditions
min
ENA = 0V, VIN = 3V or 0V
ENA = 3V, VIN = 3V or 0V
ENA = 3V, VIN = 3V or 0V, IOUT = 100mA
ENA = 3V, VIN = 3V or 0V, IOUT = 200mA
VIN = 3V
VENA = 3V
typ
0.1
13
0.2
0.4
40
40
max
1
19
0.3
0.6
60
60
μA
mA
V
V
μA
μA
Unit
Package Dimensions
unit : mm (typ)
3428
3.0
10
500
Pd max -- Ta
Specified Substrate : 20.0×10.0×0.8mm
3
Peper phenol
Allowable power dissipation, Pd max -- mW
400
3.0
4.9
0.55
300
240
200
1 2
0.5
0.25
1.03
0.16
100
0
-20
0
20
40
60
80
100
Ambient temperature, Ta --
°C
SANYO : Micro10
Pin Assignments
0.1
VCC
IN2
ENA
IN1
(NC)
1
2
3
4
5
Top view
10 OUT4
9
LB1935FA
8
7
6
OUT3
OUT1
OUT2
GND
No.A2060-2/4
LB1935FA
Block Diagram
Truth Table
Input
ENA
L
H
IN1
-
L
L
H
H
IN2
-
L
H
H
L
OUT1
OFF
H
H
L
L
OUT2
OFF
L
L
H
H
Output
OUT3
OFF
H
L
L
H
OUT4
OFF
L
H
H
L
Remarks
Standby
2-phase excitation
No.A2060-3/4
LB1935FA
Timing Chart
Timing chart below shows the 2 phase excitation stepping motor.
ENA
IN1
IN2
OUT1
OUT2
OUT3
OUT4
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using
products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd.
products described or contained herein.
Regarding monolithic semiconductors, if you should intend to use this IC continuously under high temperature,
high current, high voltage, or drastic temperature change, even if it is used within the range of absolute
maximum ratings or operating conditions, there is a possibility of decrease reliability. Please contact us for a
confirmation.
SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all
semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or
malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise
to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt
safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not
limited to protective circuits and error prevention circuits for safe design, redundant design, and structural
design.
In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are
controlled under any of applicable local export control laws and regulations, such products may require the
export license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise,
without the prior written consent of SANYO Semiconductor Co.,Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the
SANYO Semiconductor Co.,Ltd. product that you intend to use.
Upon using the technical information or products described herein, neither warranty nor license shall be granted
with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third
party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's
intellectual property rights which has resulted from the use of the technical information and products mentioned
above.
This catalog provides information as of May, 2012. Specifications and information herein are subject
Does it mean that the tri-state gate and OD gate are removed? What is the reason for this warning? My code is cut out as follows: inout dq; reg oe; assign dq = oe?1'b0:1'bz; Is there any problem with ...
Today I saw a chip CD4504, which is a TTL to COMS level chip. TI's chip is marked as CM504B, and the chip CD4051B I bought is marked as CM051B. It seems that CD4 has been replaced by CM. Haha, I almos...
I just started learning arm-linux recently. I have a 2410 development board on hand. I have read some things, but I am stuck on a problem. Don't laugh at me~ beginner~：：：：：：：：：：：：：：：：：：：：：：：：：：：：：：：：：...
It is still a launchpad expansion board with rich resources[table=98%,rgb(249, 249, 249)] [tr][td]ompatibility[/td][td]MSP430 LaunchPad[/td][/tr] [tr][td]Power[/td][td]3.3V via expansion header[/td][/...
This paper introduces the design method of a Ku-band dual-feed high-frequency head developed. Main performance indicators required by the project 1. Performance indicator requirements (1) Input freque...
No matter which processor you are learning, the first thing you need to understand is the registers and working mode of the processor.
ARM has 37 registers, including 31 general registers and ...[Details]
System design is a complex process. It is not enough to just use ICs. There are many details to consider. This article uses a high-fidelity music playback system as an example to introduce how to s...[Details]
1. With the development of modern industry and the continuous improvement of automation, some medium and large control systems have been greatly facilitated, which not only makes control easier, bu...[Details]
1. Overview
The Virtual CAN Interface (VCI) function library is an application program interface specifically provided for the use of ZLGCAN devices on PCs. The functions in the library ar...[Details]
1. Project Introduction
Shandong Dezhou Xingtai Paper Co., Ltd. is a newly built high-end paperboard production enterprise with domestic leading level established by Shandong Zhaodongfang Pape...[Details]
The potentiometer is an adjustable electronic component. The main functions of the potentiometer in the circuit are as follows:
1. Used as a voltage divider
A potentiometer is a continuou...[Details]
VP2188 is a color STN LCD module produced by Jingdian Pengyuan. This module is a dot matrix transmissive color STN display screen with a color scale of 65 k colors and white LED backlight. Its core...[Details]
Continuity test
A variety of devices need to be checked for continuity, including cable assemblies, printed circuit boards, and connectors to ensure that these components have the expected contin...[Details]
OC faults may be the most frequent and the most frequent of all faults in the inverter. They alarm during the startup process, during the shutdown process, during operation, and even when powered o...[Details]
Preface
In recent years, white light LEDs have gradually replaced incandescent bulbs and fluorescent lamps because they have unparalleled advantages over traditional light sources in terms...[Details]
1. Overview
At present, an information revolution is in the ascendant around the world, led by microelectronics, computers and communication technologies, and centered on information technolog...[Details]
1 Introduction
With the improvement of people's quality of life, lamps are no longer just basic indoor lighting tools, but also a kind of practical art for architectural decoration. When ther...[Details]
Currently, each country is developing its own USB interface
charging specifications
, which leads to a major problem that a USB interface
charging
device manufactured in one country...[Details]
0 Introduction
With the rapid development of social economy and science and technology, electric locomotives, subways and electric vehicles will be widely used. The power conversion and cont...[Details]
In the "digital pressure measurement" experimental device of applied physics, the subject technical knowledge of analog circuits, digital circuits, sensors and single-chip microcomputers is used. In o...[Details]
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
