The VC-706 incorporates a standard PECL output scheme, which are un-terminated emitters as shown in Figure 7. There are numerous application notes
on terminating and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 8, and a pull-up/pull-down scheme
as shown in Figure 9. An AC coupling capacitor is optional, depending on the application and the input logic requirements of the next stage.
LVDS Application Diagrams
V
CC
LVDS
Driver
100
LVDS
Receiver
LVDS
Driver
100
Receiver
OUT+
OUT-
Figure 11 LVDS to LVDS Connection, Internal 100ohm
Some LVDS structures have an internal 100 ohm resistor
on the input and do not need additional components.
Figure 10 Standard LVDS
Output Configuration
Figure 12 LVDS to LVDS Connection
External 100ohm and AC blocking caps
Some input structures may not have an internal 100 ohm
resistor on the input and will need an external 100ohm
resistor for impedance matching. Also, the input may have
an internal DC bias which may not be compatible with
LVDS levels, AC blocking capacitors can be used.
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-termi-
nated, and if it one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
Does Siemens' MC3i encapsulate TCP/IP? What is the concept of encapsulation? I found that some so-called GPRS Modems that encapsulate TCP/IP protocol are no different from the mc39i dial-up Internet a...
I am a junior studying software engineering and have to choose between two directions: embedded and database. I heard that embedded is very good, but it is difficult to get started. If the school is n...
Speaking of fonts, once, when I wanted to choose a good-looking font in WPS, I found that there were many beautiful fonts, such as the Founder series, which were quite good. But when I clicked it, it ...
[size=4]To learn DSP, of course, you should start with some simple test programs. It is often used to make an LED flash, but there is a misunderstanding in it. The analysis is as follows, taking the t...
Currently, each country is developing its own USB interface
charging specifications
, which leads to a major problem that a USB interface
charging
device manufactured in one country...[Details]
Among the uses of electrical energy, lighting accounts for a considerable proportion. Compared with the earlier ordinary incandescent lamps, the fluorescent lamps and energy-saving lamps we commonl...[Details]
Movpower is a portable power bank. It can charge most mobile phones and digital products, such as digital cameras, PDAs, and mobile phones such as Apple, iPod, Blackberry, Motorola, Samsung, Nokia,...[Details]
Nowadays, more and more people have digital cameras. The convenience and speed of digital cameras have gradually replaced film cameras and become the main tool for people's daily photography. The n...[Details]
Features
POE technology can ensure the safety of existing structured cabling while ensuring the normal operation of the existing network and minimizing costs. The IEEE 802.3af standard is ...[Details]
1 Introduction
Lijia'an Yellow River Diversion Culvert is a large gravity diversion gate in the lower reaches of the Yellow River. The Yellow River Diversion Culvert is located in Lijia'an Vi...[Details]
Fairchild's FAN6208 is a synchronous rectification (SR) controller for isolated LLC or LC resonant converters that can drive two individual SR MOSFETs emulating the behavior of rectifier diodes. FAN62...[Details]
The circuit has overcharge protection, over-discharge protection, over-current protection and short-circuit protection functions. Its working principle is analyzed as follows:
1 Normal state
...[Details]
(1) Open circuit voltage of the battery
(2) Internal resistance of the battery
(3) Battery operating voltage
(4) Charging voltage
Charging voltage refers to the voltage applied ...[Details]
Previously used primarily in high-power power supplies and large industrial and consumer power supplies, supercapacitors are now finding their way into products of all sizes, especially portable de...[Details]
First, the choice of charging location. Wireless charging technology is related to the distance and state of the charger and the charged device. That is to say, the distance between the two cannot...[Details]
This article starts with a comparison between two discrete MCUs and a single-chip dual-core MCU (taking LPC4350 as an example), and then introduces the basic knowledge and important features of asy...[Details]
1. Introduction
The novel bidirectional high-frequency link inverter has the advantages of bidirectional power flow, high-frequency electrical isolation, simple topology, and two-stage po...[Details]
introduction
1 The significance of using RTOS on MSP430
It is understandable that it is meaningless to use RTOS on MSP430. Because the hardware resources of MSP430 are limited (for exampl...[Details]
In a world of accelerated globalization, some major changes have actually taken place as manufacturing moves towards digitalization.
Intelligent software, new materials, sensitive robots, and ...[Details]
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
