Asynchronous operation for compatibility with industry-
standard 512K x 8 SRAMs
TTL compatible inputs and output levels, three-state
bidirectional data bus
Operational environment:
- Total dose: 50 krads(Si)
- SEL Immune 110 MeV-cm
2
/mg
- SEU LET
TH
(0.25) = 52 cm
2
MeV
- Saturated Cross Section 2.8E-8 cm
2
/bit
-<1.1E-9 errors/bit-day, Adams 90% worst case
environment geosynchronous orbit
Packaging:
- 36-lead ceramic flatpack (3.831 grams)
Standard Microcircuit Drawing 5962-00536
- QML Q and V compliant part
INTRODUCTION
The UT9Q512E RadTol product is a high-performance CMOS
static RAM organized as 524,288 words by 8 bits. Easy memory
expansion is provided by an active LOW Chip Enable (E), an
active LOW Output Enable (G), and three-state drivers.
Writing to the device is accomplished by taking Chip Enable (E)
input LOW and Write Enable (W) inputs LOW. Data on the eight
I/O pins (DQ
0
through DQ
7
) is then written into the location
specified on the address pins (A
0
through A
18
). Reading from
the device is accomplished by taking Chip Enable (E) and
Output Enable (G) LOW while forcing Write Enable (W) HIGH.
Under these conditions, the contents of the memory location
specified by the address pins will appear on the I/O pins.
The eight input/output pins (DQ
0
through DQ
7
) are placed in a
high impedance state when the device is deselected (E HIGH),
the outputs are disabled (G HIGH), or during a write operation
(E LOW and W LOW).
Clk. Gen.
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
Pre-Charge Circuit
Row Select
Memory Array
1024 Rows
512x8 Columns
I/O Circuit
Column Select
Data
Control
CLK
Gen.
A10
A11
A12
A13
A14
A15
A16
A17
A18
DQ
0
- DQ
7
E
W
G
Figure 1. UT9Q512E SRAM Block Diagram
1
DEVICE OPERATION
A0
A1
A2
A3
A4
E
DQ0
DQ1
V
DD
V
SS
DQ2
DQ3
W
A5
A6
A7
A8
A9
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
NC
A18
A17
A16
A15
G
DQ7
DQ6
V
SS
V
DD
DQ5
DQ4
A14
A13
A12
A11
A10
NC
The UT9Q512E has three control inputs called Chip Enable (E),
Write Enable (W), and Output Enable (G); 19 address inputs,
A(18:0); and eight bidirectional data lines, DQ(7:0). E controls
device selection, active, and standby modes. Asserting E enables
the device, causes I
DD
to rise to its active value, and decodes the
19 address inputs to select one of 524,288 words in the memory.
W controls read and write operations. During a read cycle, G
must be asserted to enable the outputs.
Table 1. Device Operation Truth Table
G
X
1
X
1
0
W
X
0
1
1
E
1
0
0
0
I/O Mode
3-state
Data in
3-state
Data out
Mode
Standby
Write
Read
2
Read
Figure 2. UT9Q512E 20ns SRAM Pinout (36)
PIN NAMES
A(18:0)
DQ(7:0)
E
W
G
V
DD
V
SS
Address
Data Input/Output
Chip Enable
Write Enable
Output Enable
Power
Ground
Notes:
1. “X” is defined as a “don’t care” condition.
2. Device active; outputs disabled.
READ CYCLE
A combination of W greater than V
IH
(min) and E less than V
IL
(max) defines a read cycle. Read access time is measured from
the latter of Chip Enable, Output Enable, or valid address to
valid data output.
SRAM Read Cycle 1, the Address Access in figure 4a, is
initiated by a change in address inputs while the chip is enabled
with G asserted and W deasserted. Valid data appears on data
outputs DQ(7:0) after the specified t
AVQV
is satisfied. Outputs
remain active throughout the entire cycle. As long as Chip
Enable and Output Enable are active, the address inputs may
change at a rate equal to the minimum read cycle time (t
AVAV
).
SRAM read Cycle 2, the Chip Enable - Controlled Access in
figure 4b, is initiated by E going active while G remains asserted,
W remains deasserted, and the addresses remain stable for the
entire cycle. After the specified t
ETQV
is satisfied, the eight-bit
word addressed by A(18:0) is accessed and appears at the data
outputs DQ(7:0).
SRAM read Cycle 3, the Output Enable - Controlled Access in
figure 4c, is initiated by G going active while E is asserted, W
is deasserted, and the addresses are stable. Read access time is
t
GLQV
unless t
AVQV
or t
ETQV
have not been satisfied.
2
WRITE CYCLE
A combination of W less than V
IL
(max) and E less than
V
IL
(max) defines a write cycle. The state of G is a “don’t care”
for a write cycle. The outputs are placed in the high-impedance
state when either G is greater than V
IH
(min), or when W is less
than V
IL
(max).
Write Cycle 1, the Write Enable - Controlled Access in figure
5a, is defined by a write terminated by W going high, with E
still active. The write pulse width is defined by t
WLWH
when the
write is initiated by W, and by t
ETWH
when the write is initiated
by E. Unless the outputs have been previously placed in the high-
impedance state by G, the user must wait t
WLQZ
before applying
data to the nine bidirectional pins DQ(7:0) to avoid bus
contention.
Write Cycle 2, the Chip Enable - Controlled Access in figure
5b, is defined by a write terminated by E going inactive. The
write pulse width is defined by t
WLEF
when the write is initiated
by W, and by t
ETEF
when the write is initiated by the E going
active. For the W initiated write, unless the outputs have been
previously placed in the high-impedance state by G, the user
must wait t
WLQZ
before applying data to the eight bidirectional
pins DQ(7:0) to avoid bus contention.
OPERATIONAL ENVIRONMENT
Table 2. Operational Environment
Design Specifications
1
Total Dose
Heavy Ion
Error Rate
2
50
<1.1E-9
krad(Si)
Errors/Bit-Day
Notes:
1. The SRAM will not latchup during radiation exposure under recommended
operating conditions.
2. Adam’s 0% worst case environment, Geosynchronous orbit, 100 mils of
Aluminum.
3
ABSOLUTE MAXIMUM RATINGS
1
(Referenced to V
SS
)
SYMBOL
V
DD
V
I/O
T
STG
P
D
T
J
Θ
JC
I
I
PARAMETER
DC supply voltage
Voltage on any pin
Storage temperature
Maximum power dissipation
Maximum junction temperature
2
Thermal resistance, junction-to-case
3
DC input current
LIMITS
-0.5 to 7.0V
-0.5 to 7.0V
-65 to +150°C
1.0W
+150°C
10°C/W
±
10 mA
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device
at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability and performance.
2. Maximum junction temperature may be increased to +175°C during burn-in and steady-static life.
3. Test per MIL-STD-883, Method 1012.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
T
C
V
IN
PARAMETER
Positive supply voltage
Case temperature range
DC input voltage
LIMITS
4.5 to 5.5V
(C) screening: -55°C to +125°C
(W) screening: -40°C to +125°C
0V to V
DD
4
DC ELECTRICAL CHARACTERISTICS (Pre/Post-Radiation)*
-55°C to +125°C for (C) screening and -40
o
C to +125
o
C for (W) screening (V
DD
= 5.0V + 10%)
SYMBOL
V
IH
V
IL
V
OL1
V
OL2
V
OH1
V
OH2
C
IN1
C
IO1
I
IN
I
OZ
PARAMETER
High-level input voltage
Low-level input voltage
Low-level output voltage
Low-level output voltage
High-level output voltage
High-level output voltage
Input capacitance
Bidirectional I/O capacitance
Input leakage current
Three-state output leakage current
(TTL)
(TTL)
I
OL
= 8mA, V
DD
=4.5V (TTL)
I
OL
= 200μA,V
DD
=4.5V (CMOS)
I
OH
= -4mA,V
DD
=4.5V (TTL)
I
OH
= -200μA,V
DD
=4.5V (CMOS)
ƒ
= 1MHz @ 0V
ƒ
= 1MHz @ 0V
V
IN
= V
DD
and V
SS,
V
DD
= V
DD
(max)
V
O
= V
DD
and V
SS
V
DD
= V
DD
(max)
G = V
DD
(max)
V
DD
= V
DD
(max), V
O
= V
DD
V
DD
= V
DD
(max), V
O
= 0V
I
DD
(OP)
4
Supply current operating
@ 1MHz
Inputs: V
IL
= 0.8V,
V
IH
= 2.0V
I
OUT
= 0mA
V
DD
= V
DD
(max)
Inputs: V
IL
= 0.8V,
V
IH
= 2.0V
I
OUT
= 0mA
V
DD
= V
DD
(max)
Inputs: V
IL
= V
SS
I
OUT
= 0mA
E = V
DD
- 0.5
V
DD
= V
DD
(max)
V
IH
= V
DD
- 0.5V
-55°C, -40°C, 25°C
125°C
50
mA
-2
-2
2.4
3.2
10
12
2
2
CONDITION
MIN
2
0.8
0.4
0.05
MAX
UNIT
V
V
V
V
V
V
pF
pF
μA
μA
I
OS2, 3
Short-circuit output current
-90
90
mA
I
DD
(OP)
4
Supply current operating
@50MHz
76
mA
I
DD
(SB)
Supply current standby
@0MHz
10
45
mA
mA
Notes:
* Post-radiation performance guaranteed at 25°C per MIL-STD-883 Method 1019.
1. Measured only for initial qualification and after process or design changes that could affect input/output capacitance.
2. Supplied as a design limit but not guaranteed or tested.
3. Not more than one output may be shorted at a time for maximum duration of one second.
Speaking of the difficulties of switching power supply, PCB layout is not a big problem, but if you want to lay out a good PCB board, it must be one of the difficulties of switching power supply (PCB ...
There are many bank branches, which are spread all over the city and the countryside. The use environment of each branch and self-service bank ATM machine is different, and the security system must ov...
Huawei's Beijing Research Institute is currently recruiting from the public, mainly engaged in the development of data communication products, with the following requirements: 1. Must have graduated b...
New C2000 F2833x Teaching ROM Now AvailableThe new C2000 F2833x Teaching ROM is a comprehensive guide designed to teach new users everything about C2000 and F2833x devices. The content of this teachin...
When calling API functions in the kernel, connection errors will occur. How can experts solve this problem? hal.lib(cfw.obj) : error LNK2019: unresolved external symbol MapViewOfFile referenced in fun...
Our teacher asked us to make an amplifier circuit, requiring it to be amplified 10,000 times. The signal frequency is about 76.2MHz. We need to consider the bandwidth and input impedance matching. I w...
There are three types of mobile TV: one is based on analog TV broadcasting network, another is based on mobile communication network, and the other is based on digital broadcasting network. The f...[Details]
As cellular phones become more advanced, the power consumption of the system during operation and the power consumption during standby are also increasing. Therefore, the power management design of...[Details]
1. System Structure
This system is a simulation system of indoor air-conditioning temperature/humidity control system. The data acquisition and control center collects temperature/humidity...[Details]
Product series: PB-B-RS232/485 interface (hereinafter sometimes referred to as "interface") is a product in the PROFIBUS bus bridge series.
The main purpose of the bridge series ...[Details]
With the rapid development of intelligent control technology, computers and information technology, the trend of information appliances IA (Information Application), computers and communications integ...[Details]
Toyohashi University of Technology demonstrated electric field coupled wireless power supply technology using life-size car tires and roads at the wireless technology exhibition "Wireless Technolog...[Details]
Experimental tasks
A DS18B20 is used to form a temperature measurement system. The temperature measurement accuracy reaches 0.1 degrees. The temperature range is between -20 degrees and +50 de...[Details]
Problems such as the depletion of natural resources, air pollution, traffic congestion, and rising fossil fuel prices have forced societies and individuals to seek alternative means of transportati...[Details]
1. When the slip speed regulating motor is undergoing frequency conversion and energy saving transformation, the original excitation box (referred to as the speed regulating box) and the original s...[Details]
Motors, especially those with brushes, generate a lot of noise. This noise must be dealt with if the appliance is to meet the requirements of EMC standards. The means to solve EMC are nothing more ...[Details]
In 2012, more than half of the cars in the European, Japanese and American car markets will be equipped with color displays, navigation systems, satellite communications and other in-vehicle infota...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guangzho...[Details]
LED is the abbreviation of the English word. Its main meanings are: LED = Light Emitting Diode, a solid-state semiconductor device that can convert electrical energy into visible light. It can dire...[Details]
Against the backdrop of global warming, energy conservation and emission reduction have become a global hotspot and focus, which has also sounded the clarion call for the take-off of the LED lighti...[Details]
PCB Design
京公网安备 11010802033920号
EEWORLD
