MAX1082_C_E/MAX1083_CUE ......................... 0°C to +70°C
MAX1082_E_E/MAX1083_EUE ....................... -40°C to +85°C
Storage Temperature Range ............................ -60°C to +150°C
Lead Temperature (soldering, 10s) ................................ +300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
[i=s]This post was last edited by Changjianze1 on 2022-8-9 17:57[/i]Take a look at and compare ST's F4 chip, but the AT one is a value-for-money model, so its functions may be compromised.The biggest ...
The entire power supply is required to come from a 2.5V farad capacitor, and the current of the LED is controlled by a single-chip microcomputer with a 1~20mA step-by-step adjustable. Now I only know ...
Use 74ls90 counter and 74ls08, 74ls123 monostable trigger, and DIP switch to make a counter frequency division circuit. Use audio signal generator to generate 1kHz square wave signal and connect it to...
I just learned driver development. Does anyone have the software Microsoft Platform Builder for Windows Mobile 5.0? Can you send it to me in separate files? 634173898@qq.com I will never forget your k...
I have made a 6×5 special keyboard. In the program, the make and break codes of the keys are sent to the industrial control computer. The industrial control computer can receive and display them corre...
1. Hardware modification:2. Software modification:in order to disable the built-in DC/DC, write this in your ccfg.c:#define SET_CCFG_MODE_CONF_DCDC_RECHARGE 0x1 // Do not use the DC/DC during recharge...
In the previous article, I wrote a simple GPIO running light test, which looked a bit monotonous. I was used to serial port debugging. If there was no serial port on the board, I had to find another ...[Details]
After we understand the use of libopencm3, we find that libopencm3 is only suitable for small projects. Its biggest feature is the convenience of USB. So when we configure large projects, is there a ...[Details]
Chip: STM32F107VCT6 Application Pin: THOUSANDS, RMII STM32CubeMX is very convenient to use ETH. The software comes with LWIP and configuration. This time, STM32F107VCT6+DP83848CVV is used. The MII a...[Details]
In 1952, Bell Labs built a 6-foot-tall automatic number recognition machine called "Audrey", which could recognize the pronunciation of the numbers 0 to 9 with an accuracy of more than 90%. And its...[Details]
In the Chinese automobile market, the trend of new energy vehicles and driverless cars is leading the transformation of China's automobile industry. As the world's largest automobile market, "Chinese...[Details]
In the project, CPLD is needed to complete part of the algorithm design. The parameters are given by AVR, so the communication between AVR and CPLD needs to be completed. Therefore, a test program is...[Details]
Temperature, humidity and irradiance are must-measure items in the photovoltaic industry. However, most of the current data collection is done by storing data in USB flash drives for offline analys...[Details]
The implementation of CAN driver under embedded operating system Android requires not only adding CAN driver device in Linux kernel, but also implementing the call of Android HAL layer. Taking S5...[Details]
Household photovoltaic power stations mainly utilize idle resources on existing household buildings, such as roofs, wall facades, balconies, courtyards, etc., to install and use distributed photovo...[Details]
sprintf is a function in the C language library that converts data types. There is a situation where In 51 MCU, define unsigned char temp; Then I want to use the serial port to print out temp in deci...[Details]
6MHz crystal oscillator, using timer counter 1, using interrupt mode, through P1.0 to make a light emitting diode turn on for 100ms, turn off for 300ms, and repeat. Assembly programming is used to ac...[Details]
Using AT89S51 microcontroller, modify the original one to turn the LED on for 4s and off for 2s. Thank you. Use a timer. (The program is written in the answer, omitted here - just a note) The origi...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
