DICE SPECIFICATION
RH1078M
Micropower, Dual, Single-Supply
Precision Op Amp
DIE CROSS REFERENCE
6
5
LTC Finished
Part Number
RH1078M
Order DICE CANDIDATE
Part Number
RH1078M DICE
Please refer to LTC standard product data sheet for
other applicable product information.
PAD FUNCTION
7
8
1
4
1.
2.
3.
4.
5.
6.
7.
8.
OUTA
–INA
+INA
–V
+INB
–INB
OUTB
+V
12mils thick,
backside (substrate) is an alloyed
gold layer. Connect backside to V–.
2
3
90 × 97 mils
L,
LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear
Technology Corporation. All other trademarks are the property of their respective owners.
DICE ELECTRICAL TEST LIMITS
SYMBOL
V
OS
I
OS
I
B
CMRR
PSRR
PARAMETER
Input Offset Voltage
Input Offset Current
Input Bias Current
Common Mode Rejection Ratio
Power Supply Rejection Ratio
T
A
= 25°C, V
S
= 5V, V
CM
= 0.1V, V
OUT
= 1.4V, unless otherwise specified.
MIN
MAX
120
0.8
15
UNITS
μV
nA
nA
dB
dB
dB
dB
CONDITIONS
V
CM
= 0V to 3.5V
V
CM
= 0.05V to 3.2V
V
S
= 2.3V to 12V
V
S
= 3.1V to 12V
94
100
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa-
tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.
1
DICE SPECIFICATION
RH1078M
DICE ELECTRICAL TEST LIMITS
SYMBOL
A
VOL
PARAMETER
Large-Signal Voltage Gain
T
A
= 25°C, V
S
= 5V, V
CM
= 0.1V, V
OUT
= 1.4V, unless otherwise specified.
MIN
150
120
MAX
UNITS
V/mV
V/mV
V/mV
V/mV
6
2
130
4.2
3.5
0.04
75
2.3
350
mV
mV
mV
V
V
V/μs
μA
V
CONDITIONS
V
O
= 0.03V to 4V, No Load
V
O
= 0.03V to 3.5V, R
L
= 50k
V
O
= 0.05V to 4V, No Load
V
O
= 0.05V to 3.5V, R
L
= 50k
Output Low, No Load
Output Low, 2k to GND
Output Low, I
SINK
= 100μA
Output High, No Load
Output High, 2k to GND
A
V
= 1, V
S
= ±2.5V
Per Amplifier
Note 2
V
OUT
Output Voltage Swing
SR
I
S
Slew Rate
Supply Current
Minimum Supply Voltage
T
A
= 25°C, V
S
= ±15V, unless otherwise specified.
SYMBOL
V
OS
I
OS
I
B
PARAMETER
Input Offset Voltage
Input Offset Current
Input Bias Current
Input Voltage Range
CMRR
PSRR
A
VOL
Common Mode Rejection Ratio
Power Supply Rejection Ratio
Large-Signal Voltage Gain
V
CM
= 13.5V, –15V
V
CM
= 13V, –14.9V
V
S
= 5V, 0V to ±18V
V
O
= ±10V, R
L
= 50k
V
O
= ±10V, R
L
= 2k
V
O
= ±10V, R
L
= 5k
RL = 50k
RL = 2k
RL = 5k
Per Amplifier
13.5
–15.0
97
100
1000
300
±13
±11
0.06
100
CONDITIONS
MIN
MAX
350
0.8
15
UNITS
μV
nA
nA
V
V
dB
dB
dB
V/mV
V/mV
V/mV
V
V
V
V/μs
μA
V
OUT
Output Voltage Swing
SR
I
S
Slew Rate
Supply Current
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
Power supply rejection ratio is measured at the minimum supply
voltage.
Wafer level testing is performed per the indicated specifications for dice. Considerable differences in performance can often be observed for dice versus
packaged units due to the influences of packaging and assembly on certain devices and/or parameters. Please consult factory for more information
on dice performance and lot qualifications via lot sampling test procedures.
Dice data sheet subject to change. Please consult factory for current revision in production.
I.D.No. 66-13-1078
2
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900
●
FAX: (408) 434-0507
●
LT 0912 REV A • PRINTED IN USA
www.linear.com
LINEAR TECHNOLOGY CORPORATION 2005
京公网安备 11010802033920号
EEWORLD
