MAFA 1000 Series Erbium Doped Fiber Micro Amplifier
EMCORE’s MAFA 1000 Series Erbium Doped Fiber micro Amplifier (μEDFA)
Gain Block Module is an ideal building block for OEM system integrators. The
family of MAFA 1000 EDFA Gain Blocks is designed to meet the most demanding
noise performance requirements of fiber optic communications and control
systems, and performs all the functions required of an optical amplifier for system
integration.
MAFA 1000 series EDFA Gain Blocks provide input and output optical isolation for
stable, low noise operation. The input and output optical signal power levels are
detected for monitoring and control. The input optical signal is amplified with
active gain control for a constant output power level or with active output power
control for constant gain mode operation.
The MAFA 1000 series EDFA Gain Blocks also provide monitors and associated
alarms for all critical operating parameters. The optical output of the MAFA 1000
series EDFA Gain Blocks can be split into multiple ports by optional external
splitter. Optional back reflection monitoring feature enables safe output optical
power managing.
The compact mechanical footprint of the MAFA 1000 allows using this unit to be
installed in small space environments.
Applications
CATV Systems
Long Distance RF/Microwave Fiber
Optic Communication Links
Sensing and Control Systems
High Performance Supertrunking Links
High Power Distribtuion Networks
Redundanct Ring Architectures
FTTx Networks
Features
Full Function Fiber Optic Amplifier
Ready for Integration
Low Noise Figure (Typ < 4.5 dB)
Pin: -6 dBm to +12 dBM
Pout: +14 dBm to +23 dBm
RS-232 Monitor and Control Interface
(SNMP V.1 is also possible)
Standard and Optional Gain Flatness
Low Electrical Power Consumption
Input/Output Isolation >40/40 dB
Polarization Dependant Gain < 0.1 dB
Polarization Mode Dispersion < 0.2 ps
Input & Output Return Losses < -40 dB
Output Residual Pump Power < -30 dBm
Back Reflection Monitoring
|
REV 2012.09
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
MAFA 1000 Series EDFA
DATASHEET | SEPTEMBER 2012
FIBER OPTICS
Optical/Electrical Characteristics
1
Property
Unit
Limit
1014
Operating Input Power
Operating Input Power
Output Power
Noise Figure
Static Gain Flatness
Dynamic Gain Flatness
Output Power Stability
Power Consumption
(Steady state)
Pin (dBm)
Pin (dBm)
Po(dBm)
NF (dB)
ΔGs
(dB)
ΔGd
(dB)
(dB)
Psys(W)
Max
Min
Nominal
Typ
Max
Max
Max
Max
12
-6
14
+/-.25
4.0 dB
+/-0.5
+/-1.0
+/- 0.1
2
Models
1017
12
-6
17
+/- .25
4.0 dB
+/-0.5
+/-1.25
+/- 0.1
3
Comments
1022
12
-6
22
+/- .25
4.0 dB
+/-0.5
+/-2.0
+/- 0.1
6
1020
12
-6
20
+/- .25
4.0 dB
+/-0.5
+/-1.5
+/- 0.1
5
1023
12
-6
23
+/- .25
4.0 dB
+/-0.5
+/-2.0
+/- 0.1
8
Typical
(May vary for some models)
Note 2
@ Pin = 0 dBm, no Pin monitoring
(Notes 3, 7, 8)
(Notes 4)
(Notes 5, 7)
(Note 6)
70 C Case
o
Notes:
1. Unless stated otherwise, all specifications apply over the full operating temperature and humidity ranges
0 dBm. Measuring with 1 input optical signal with Pin
≈
0 dBm and
≈
1550 nm is also available
4. Measured with a swept Probe Signal (Pp), where Pp
≈
0 dBm @ 25C
5. Measured with a swept Probe Signal (Pp), and a fixed Tone Signal (Pt) @ ~ 1550 nm; (Pt
≈
Pp+20 dB; Pt + Pp
≈
0 dBm)
@ 25C; Gain Flattened Options with
ΔG ≤
+/-0.75dB or
ΔG ≤
+/-1.0dB are available (for
some models and for defined
input optical power only)
6. Over polarization and temperature
7. Specific
ΔG
can be guaranteed at a single specified Input Optical Power Level (Pin = Pt + Pp) equal or different from 0
dBm
8. If input power monitoring and input isolation are required then typical NF (Typ) for all units @ Pin = 0 dBm as
4.5 dB
General and Mechanical Specifications
Property
Operating Wavelength
Operating Case Temperature
Storage Temperature
Operating Humidity
Voltage Supply Range
Optical Connectors
Dimensions (mm)
Requirement
1532nm ~ 1565nm
0C to 50C
-40C to 85C
20% to 85%
+12VDC/+5VDC/+3.3VDC
SC; FC; E2000
70 x 90 x 15
Comments
Standard
Standard*
Standard
Non-condensing
All versions**
User Specified
All versions
* - Extended temperature range of –40C to +75C is also possible
** Transient Pulse to +X.XVDC + 5% for < 100 msec
|
REV 2012.09
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
MAFA 1000 Series EDFA
DATASHEET | SEPTEMBER 2012
FIBER OPTICS
Outline Drawing (dimensions in mm)
Compliance and Reliability Information
FCC: Subpart B. Part 15 class “A”: Unintentional Radiators
EN 55013: Sound and Television Broadcast receivers and associated equipment – Radio disturbance characteristics- limits
and methods of measurements – Electric Field Radiation Emissions (2001)
Fit Rate: 90% level of confidence - 290 @ 25C
|
REV 2012.09
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
MAFA1014-SC-00-S-2: 14 dBm gain block with SC/APC optical connectors, standard NG/GF, standard temperature range,
+5VDC power supply
Note:
Only some models can be order with Gain Flattened options. (-01 suffixes).
Please contact your Sales Representative
for details
|
REV 2012.09
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
MAFA 1000 Series EDFA
DATASHEET | SEPTEMBER 2012
FIBER OPTICS
Laser Safety Information
This product meets the applicable requirements of 21 CFR 1010 & 1040 and is classified as a Class IV laser product based
on the maximum optical output power shown below. During use as intended, the laser energy is fully contained within the
fiber network such that there is no accessible laser radiation and would meet the requirements for a Class I laser product.
The laser product report has been submitted to the CDRH and the accession number is expected by October 2006.
Wavelength = 1535 ~ 1565 nm (dependant on input source)
Maximum Output Power = 0.2 W (single output, 23 dBm model)
|
REV 2012.09
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
[align=left][backcolor=rgb(239, 245, 249)][color=rgb(84, 84, 84)][font=Arial, 宋体][size=12px]What is the problem that newbies in the electronics industry will encounter at the beginning? Some resistors...
I am currently working on a pressure indicator gauge and have a finished product in hand.
I see that they use a four-wire pressure sensor, so shouldn't there be two wires for power supply and two for ...
Sorry, I missed some points in the article [url=https://bbs.eeworld.com.cn/forum.php?mod=viewthread&tid=484889&page=1#pid1988286]《Detailed steps for installing plug-ins in Altium Designer15》[/url]. It...
I would like to ask how to reuse modules in AO PCB diagrams. Now I need to draw two Ethernet transceiver schematics with exactly the same layout and wiring. How to implement it specifically?...
I would like to ask, if I don't use TI's timing chip, how can I provide the 1.8V first and then 3.3V power supply timing for 320F2812? Can you give me a circuit? Thank you!...
I came up with a stupid idea, which is to create a BRD file, place the desired components in the file, and then open the file with DXP. However, DXP cannot display the file. Can anyone help me? Thank ...
Dual-mode inverters can operate both in conjunction with the grid and independently. These inverters can inject excess energy from renewable energy and storage devices into the grid, and withdraw p...[Details]
How do you know if a machine is operating properly? The answer: by leveraging deep learning to detect anomalies in routine vibration data from industrial machines. Anomaly detection has many uses, ...[Details]
summary
There are multiple approaches to making industrial systems more intelligent, including applying artificial intelligence (AI) technology at the edge and in the cloud to sensor...[Details]
1. Introduction
Electronic scales are gradually replacing traditional measuring tools like springs and balances in everyday life, such as electronic price computing scales and electronic weigh...[Details]
On August 21, WeRide officially launched WePilot AiDrive, a one-stage end-to-end assisted driving solution developed in cooperation with Bosch. This comes only half a year after the two parties' "t...[Details]
On August 21st, Zhiyuan Robotics revealed at its first partner conference that it expects shipments to reach thousands of units this year and tens of thousands next year. The company hopes to reach...[Details]
According to Nikkei, Japan has performed poorly in responding to China's power semiconductor challenges.
There are five major companies in Japan's power chip market: Mitsubishi Electric,...[Details]
"We have successfully launched the first version of our dedicated chip for EMB brake-by-wire. Second-generation samples have also been successfully completed, and we are actively planning a third-g...[Details]
My career has been closely tied to the semiconductor industry. From product management to content marketing, I've provided countless forecasts and predictions across a variety of roles. Whethe...[Details]
With the gradual popularization of new energy vehicles in recent years, more and more people have been able to access and purchase electric vehicles. The structure of electric vehicles is composed ...[Details]
On August 21, according to a report by Korean media SEDaily yesterday, according to semiconductor industry sources, the HBM4 samples provided by Samsung to Nvidia last month have passed initial tes...[Details]
From time to time, I see some audiophiles spending a lot of money or a lot of time to DIY speakers, but the results are not what they want. Below I list some of the small experiences I summarized b...[Details]
Facial recognition, a biometric technology that uses facial features to authenticate identity, has rapidly become a global market hotspot in recent years as the technology has entered practical use...[Details]
Qiangmao, your trusted semiconductor solutions partner, sincerely invites you to visit Electronics India 2025, South Asia's leading trade show for electronic components, systems, applications...[Details]
Nidec Precision Testing Technology Co., Ltd. will participate in "Testing Expo China—Automotive 2025" to be held at the Shanghai World Expo Exhibition and Convention Center from August 27 (Wednesda...[Details]
Test/Measurement
京公网安备 11010802033920号
EEWORLD
