531UB174M000DG datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Passive components> oscillator> 531UB174M000DG

531UB174M000DG: DescriptionCMOS/TTL Output Clock Oscillator, 174MHz Nom, ROHS COMPLIANT, SMD, 6 PIN; CategoryPassive components oscillator; File Size215KB，12 Pages; ManufacturerSilicon Laboratories Inc; Environmental Compliance

Download Datasheet Parametric View All

531UB174M000DG Overview

CMOS/TTL Output Clock Oscillator, 174MHz Nom, ROHS COMPLIANT, SMD, 6 PIN

531UB174M000DG Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	Silicon Laboratories Inc
Reach Compliance Code	unknown
Other features	TRAY
maximum descent time	0.35 ns
Frequency Adjustment - Mechanical	NO
frequency stability	20%
JESD-609 code	e4
Manufacturer's serial number	531
Installation features	SURFACE MOUNT
Nominal operating frequency	174 MHz
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
Oscillator type	CMOS/TTL
physical size	7.0mm x 5.0mm x 1.85mm
longest rise time	0.35 ns
Maximum supply voltage	2.75 V
Minimum supply voltage	2.25 V
Nominal supply voltage	2.5 V
surface mount	YES
maximum symmetry	55/45 %
Terminal surface	Nickel/Gold (Ni/Au)

Preview

Download Datasheet

View All

S i 5 3 0 / 5 31

EVISION

R Y S TA L

S C I L L A T O R

(XO)

(10 M H

Z T O

1.4 G H

)

Features

Available with any-rate output

frequencies from 10 MHz to 945 MHz

and select frequencies to 1.4 GHz

3rd generation DSPLL

with superior

jitter performance

3x better frequency stability than

SAW-based oscillators

Internal fixed crystal frequency

ensures high reliability and low

aging

Available CMOS, LVPECL,

LVDS, and CML outputs

3.3, 2.5, and 1.8 V supply options

Industry-standard 5 x 7 mm

package and pinout

Pb-free/RoHS-compliant

Si5602

Ordering Information:

See page 7.

Applications

SONET/SDH

Networking

SD/HD video

Test and measurement

Clock and data recovery

FPGA/ASIC clock generation

Pin Assignments:

See page 6.

(Top View)

GND

Description

The Si530/531 XO utilizes Silicon Laboratories’ advanced DSPLL circuitry

to provide a low jitter clock at high frequencies. The Si530/531 is available

with any-rate output frequency from 10 to 945 MHz and select frequencies to

1400 MHz. Unlike a traditional XO, where a different crystal is required for

each output frequency, the Si530/531 uses one fixed crystal to provide a

wide range of output frequencies. This IC based approach allows the crystal

resonator to provide exceptional frequency stability and reliability. In addition,

DSPLL clock synthesis provides superior supply noise rejection, simplifying

the task of generating low jitter clocks in noisy environments typically found in

communication systems. The Si530/531 IC based XO is factory configurable

for a wide variety of user specifications including frequency, supply voltage,

output format, and temperature stability. Specific configurations are factory

programmed at time of shipment, thereby eliminating long lead times

associated with custom oscillators.

CLK–

CLK+

Si530 (LVDS/LVPECL/CML)

GND

Functional Block Diagram

CLK– CLK+

CLK

Si530 (CMOS)

Fixed

Frequency

Any-rate

10–1400 MHz

DSPLL

Clock

Synthesis

GND

CLK–

CLK+

Si531 (LVDS/LVPECL/CML)

GND

Rev. 1.1 6/07

Si530/531

Recommended Resources

Self-contained bias common source amplifier circuit

Edifier 2.1 subwoofer circuit diagram produced by tda1521

Overvoltage protector circuit (1)

A Xipu soft starter drives a three-state motor control circuit

875p computer motherboard circuit diagram_090

Questions about UART: I use USB to connect RS-232 and use the terminal to send and receive. I measured the waveform to be about 10KHz, but my UART1 measured it to be about 13KHz. My BAUD is set to 9600. I want to adjust th...; prince6150 stm32/stm8

Novice's solution to the current size in low power mode: #include void main(void) { WDTCTL = WDTPW + WDTHOLD; P1DIR = BIT0; P1OUT = BIT0; LPM4; } After writing this code, shouldn't it enter low power mode 4 in the end? Then I connected a multimeter in serie...; Xman0_0 Microcontroller MCU

Signal input mode of power amplifier: [size=4]The signal input mode selection problem of the power amplifier. In professional audio engineering, we often encounter problems such as signal parallel connection and bridging. First of all, we...; Jacktang Analogue and Mixed Signal

DIY a MSP430 BSL download programmer: ...; fengzhang2002 Microcontroller MCU

The forum is huge, where should I start learning?: Hello everyone, I am a student, now studying Automation at Guangdong University of Technology. I don't know what I should study. The forum is so big that I don't know where to start. Although I am alr...; zuopie Talking

Question: Problems with stm32 timer and external interrupt: What is the difference between the interrupt in the input capture mode of the stm32 timer and the external interrupt? Both of them execute the interrupt program after capturing the edge of the signal....; 雨夏 stm32/stm8

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components