1A Positive Low Dropout Fixed-Mode Regulator With EN Function
Features
•
1.4V
General Description
AP1118 is a low dropout positive fixed-mode
regulator with minimum of 1A output current
capability. The product is specifically designed to
provide well-regulated supply for low voltage IC
applications such as high-speed bus termination
and low current 3.3V logic supply. AP1118 is also
well suited for other applications such as VGA
cards. AP1118 is guaranteed to have <1.4V
dropout at full load current making it ideal to provide
well regulated outputs of 1.25 to 12V with up to 18V
input supply. The AP1118 offers a TTL – Logic
compatible enable pin.
maximum dropout at full load current
•
Fast transient response
•
Output current limiting
•
Built-in thermal shutdown
•
Packages: TO220-5, TO252-5, TO263-5, SOP8
•
Good noise rejection
•
Fixed Output 1.5V, 1.8V, 2.5V, 3.3V, 5.0V, 9.0V,
12V
•
Enable function
Applications
•
•
•
PC peripheral
Communication
CDROM..
Ordering Information
AP 1118 X XX X X
Low Dropout Regulator
Package
D : TO252-5L
T : TO220-5L
K : TO263-5L
S : SOP-8L
Vout
15 : 1.5V
18 : 1.8V
25 : 2.5V
33 : 3.3V
50 : 5.0V
90 : 9.0V
12 : 12V
Lead Free
Blank : Normal
L : Lead Free Package
Packing
Blank : Tube
A : Taping
Typical Circuit
5V
C1
100uF
Vin
EN
Tab is Vout
Vout
NC
GND
C2
100uF
3.3V/1A
( 5V/3.3V fixed output )
This datasheet contains new product information. Anachip Corp. reserves the rights to modify the product specification without notice. No liability is assumed as a result of the use of
this product. No rights under any patent accompany the sale of the product.
Rev. 1.1
1/10
Feb. 15, 2005
AP1118
1A Positive Low Dropout Fixed-Mode Regulator With EN Function
Connection Diagram
5 PIN TO220
5 PIN TO252/TO263
( Top View )
5
Vin
EN
Vout
NC
GND
Tab is Vout
4
3
2
1
Vin
EN
Vout
NC
GND
5
4
3
2
1
Tab is Vout
SOP-8L
( Top View )
Vout
Vout
Vout
Vout
5
6
7
8
4
3
2
1
Vin
EN
Vout
GND
Pin Descriptions
NAME
GND
Vout
Ground.
The output of the regulator. A minimum of 10uF capacitor must be connected from this pin
to ground to insure stability.
The input pin of regulator. Typically a large storage capacitor is connected from this pin to
ground to insure that the input voltage does not sag below the minimum dropout voltage
during the load transient response. This pin must always be 1.3V higher than Vout in order
for the device to regulate properly.
The input pin of regulator. TTL/CMOS compatible input Logic high = disable output, Logic
Low or open = output enable. (internal pull-down resistor~100 K).
No connection.
FUNCTION
Vin
EN
NC
Anachip Corp.
www.anachip.com.tw
2/10
Rev.1.1
Feb. 15, 2005
AP1118
1A Positive Low Dropout Fixed-Mode Regulator With EN Function
Absolute Maximum Ratings
Characteristics
DC Supply Voltage
Enable Pin Voltage
Power Dissipation
Storage Temperature
Operating Junction Temperature Range
Symbol
Vin
V
EN
P
D
T
ST
T
OP.
Values
-0.3 to 18
7
Internally Limited
-65 to +150
0 to +150
oC
oC
Unit
V
V
Electrical Characteristics
(Under Operating Conditions)
PARAMETER
AP1118-1.5
AP1118-1.8
AP1118-2.5
Output Voltage
AP1118-3.3
AP1118-5.0
AP1118-9.0
AP1118-12.0
Line Regulation
AP1118-XXX
AP1118-1.5
AP1118-1.8
AP1118-2.5
Load Regulation
AP1118-3.3
AP1118-5.0
AP1118-9.0
AP1118-12.0
Dropout Voltage
(V
IN
-V
OUT
)
AP1118- 1.5/1.8
2.5/3.3/5.0/9.0/12
CONDITIONS
I
OUT
= 10mA, T
J
= 25 C,
3V≦V
IN
≦15V
o
I
OUT
= 10mA, T
J
= 25 C,
3.3V≦V
IN
≦15V
o
I
OUT
= 10mA, T
J
= 25 C,
4V≦V
IN
≦15V
I
OUT
= 10mA, T
J
= 25
o
C,
4.8V≦V
IN
≦15V
I
OUT
= 10mA, T
J
= 25
o
C,
6.5V≦V
IN
≦15V
o
I
OUT
= 10mA, T
J
= 25 C,
10.5V≦V
IN
≦18V
o
I
OUT
= 10mA, T
J
= 25 C,
13.5V≦V
IN
≦18V
I
O
=10mA,V
OUT
+1.5V<V
IN
<18V,
o
T
J
=25 C
V
IN
=3V, 0mA<Io<1A,
o
T
J
=25 C (Note 1,2)
V
IN
=3.3V, 0mA<Io<1A,
T
J
=25
o
C (Note 1,2)
V
IN
=4V, 0mA<Io<1A,
o
T
J
=25 C (Note 1,2)
V
IN
= 5V, 0≦I
OUT
≦1A,
T
J
=25
o
C (Note 1,2)
V
IN
= 8V, 0≦I
OUT
≦1A,
T
J
=25
o
C (Note 1,2)
V
IN
=12V, 0≦I
OUT
≦1A,
o
T
J
=25 C (Note 1,2)
V
IN
=15V, 0≦I
OUT
≦1A,
o
T
J
=25 C (Note 1,2)
I
OUT
= 1A ,
∆V
OUT
=0.1V
o
MIN
1.470
1.764
2.450
3.235
4.900
8.820
11.760
TYP
1.500
1.800
2.500
3.300
5.000
9.000
12.000
MAX
1.530
1.836
2.550
3.365
5.100
9.180
12.240
0.2
UNIT
V
V
V
V
V
V
V
%
mV
mV
mV
mV
mV
mV
mV
V
12
15
20
26
40
70
100
1.3
15
18
25
33
50
90
120
1.4
Anachip Corp.
www.anachip.com.tw
3/10
Rev.1.1
Feb. 15, 2005
AP1118
1A Positive Low Dropout Fixed-Mode Regulator With EN Function
Electrical Characteristics(Continued)
PARAMETER
Current Limit
Minimum Load Current
V
EN
I
EN
Thermal Regulation
Ripple Rejection
Temperature Stability
AP1118- 1.5/1.8
2.5/3.3/5.0/9.1/12
AP1118-XXX
Enable Input Voltage
Enable Input Current
T
A
=25
O
C, 30ms pulse
F=120Hz,C
OUT
=25uF Tantalum, I
OUT
=1A
AP1118-XXX
I
O
=10mA
V
IN
=V
OUT
+3V
CONDITIONS
(V
IN
-V
OUT
) = 5V
0 C≦Tj≦125 C
Logic Low (ON)
Logic High (OFF)
V
EN
= 0.8V
V
EN
= 2.0V
o
o
(Under Operating Conditions)
MIN
1. 1
5
1.6
10
80
0.008
60
0.5
150
102
85
90
25
15
0.65/2.7
3.5
0.04
70
10
0.8
TYP
MAX
UNIT
A
mA
V
µA
%/W
dB
%
θ
JA
Thermal Resistance SOP-8L
Junction-to-Ambient(No
heat sink ;No air flow)
TO-252-5L
TO-220-5L
TO263-5L
SOP-8L
O
C/W
θ
JC
Thermal Resistance TO-252-5L
Junction-to-Case
TO-220-5L
TO263-5L
: Control Circuitry/Power Transistor
O
C/W
Note1: See thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are
measured at a constant junction temperature by low duty cycle pulse testing. Load regulation is measured at the output lead =
1/18” from the package.
Note2: Line and load regulation are guaranteed up to the maximum power dissipation of 15W. Power dissipation is determined by the
input/output differential and the output current. Guaranteed maximum power dissipation will not be available over the full
input/output range.
Note3: Quiescent current is defined as the minimum output current required to maintain regulation. At 12V input/output differential the
device is guaranteed to regulate if the output current is greater than 10mA.
Anachip Corp.
www.anachip.com.tw
4/10
Rev.1.1
Feb. 15, 2005
AP1118
1A Positive Low Dropout Fixed-Mode Regulator With EN Function
Today, I received a UFUN. However, I looked at the information on the forum and it showed the blueprint of VERA, but the UFUN I have is VERB. Where is the blueprint of VERB? ???
It is obvious that the...
I am using arm's s3c2440 microcontroller to communicate with trf7960. I want to read the card number of a card that complies with the 14443a protocol, but I am using spi communication simulated by a n...
ADS2004A ADS2003C HFSS9.2 Ansoft Designer Zeland IE3D9.2 XFDTD6.0 Serenade CSTThe design of microwave systems is becoming more and more complex, the requirements for circuit indicators are getting hig...
There are three types of mobile TV: one is based on analog TV broadcasting network, another is based on mobile communication network, and the other is based on digital broadcasting network. The f...[Details]
The data collector of the automatic weather station is generally designed based on a single-chip microcomputer or a PC/104 bus controller. It has the characteristics of good compatibility with PC, low...[Details]
With the advocacy and implementation of the government's Safe City Plan, the security market has increasingly higher requirements for the clarity of surveillance images. Imagine that after a case o...[Details]
Nippon Electric Works and Volvo Technology Japan have developed a wireless power supply system for electric vehicles (EVs). Using this system, the two companies have successfully conducted an exper...[Details]
Toyohashi University of Technology demonstrated electric field coupled wireless power supply technology using life-size car tires and roads at the wireless technology exhibition "Wireless Technolog...[Details]
1. When the slip speed regulating motor is undergoing frequency conversion and energy saving transformation, the original excitation box (referred to as the speed regulating box) and the original s...[Details]
The above is to use MB1404 as a stereo composite signal transmitter. You can use the internal high-frequency amplifier and oscillator or not! According to my experience, I still recommend beginners...[Details]
0 Introduction
Wireless Sensor Network (WSN) monitors the target by deploying a large number of sensor nodes in the target area. WSN realizes the positioning and tracking of the target, determi...[Details]
introduction
At present, the research on micron and nanotechnology is very active, which has led to the rapid development of microtechnology and micro-mechanical electronic system (MEMS) t...[Details]
Cars equipped with xenon headlights are already common on the road. Whether they are standard equipment on high-end cars or embellishments on modified cars, xenon lamps are gradually becoming a sym...[Details]
The installation locations of DC-DC converters are relatively scattered. DC-DC converters can be found on the power board, main board, logic control board and other circuit boards of PDP color TVs....[Details]
The overall operating performance of an electric car depends first on its battery system and motor drive system. The drive system of an electric car is generally composed of three main parts: a con...[Details]
Some people think: as long as the program runs well, it doesn't matter how the original program is written. But this is absolutely not the case. Software is not completed in one go, and it is neces...[Details]
With the explosive growth of electronic functions in cars, will more and more luxurious cars endanger the safety of passengers? This is the origin of the problem of over-electrification of cars. What ...[Details]
Introduction
In the wastewater discharged from steel plants, the water contains a large amount of waste slag and oil. If the waste slag and oil are separated from the water, the water can be us...[Details]
Power technology
京公网安备 11010802033920号
EEWORLD
