EEWORLDEEWORLDEEWORLD

Part Number

Search

M300G2A

Description
Power/Signal Relay, DPDT, Momentary, 0.088A (Coil), 28VDC (Coil), 2464mW (Coil), 10A (Contact), 28VDC (Contact), DC Input, AC/DC Output, Panel Mount,
CategoryMechanical and electronic products    relay   
File Size1MB,20 Pages
ManufacturerEsterline Technologies Corporation
Download Datasheet Parametric View All

M300G2A Overview

Power/Signal Relay, DPDT, Momentary, 0.088A (Coil), 28VDC (Coil), 2464mW (Coil), 10A (Contact), 28VDC (Contact), DC Input, AC/DC Output, Panel Mount,

M300G2A Parametric

Parameter NameAttribute value
MakerEsterline Technologies Corporation
Reach Compliance Codeunknown
ECCN codeEAR99
body width13.3 mm
body height25.7 mm
Body length or diameter26 mm
Maximum coil current (DC)0.088 A
Coil operating voltage (DC)19.8 V
Coil power2628 mW
Coil release voltage (DC)1.5 V
Coil resistance320 Ω
Maximum coil voltage (DC)29 V
Coil/Input Power TypeDC
Contact (AC) maximum rated R load10A@115VAC
Maximum contact current (AC)10 A
Maximum contact current (DC)10 A
Contact (DC) maximum rated R load10A@28VDC
Maximum contact voltage (AC)115 V
Maximum contact voltage (DC)28 V
Contact/Output Power TypeAC/DC
Electrical life100000 Cycle(s)
Installation featuresPANEL MOUNT
operating hours11 ms
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
physical size26mm x 13.3mm x 25.7mm
GuidelineCECC; MIL-R-83536/9; MIL-R-83536/10
Relay actionMOMENTARY
Relay functionDPDT
Relay typePOWER/SIGNAL RELAY
release time11 ms
sealHERMETICALLY SEALED
surface mountNO
Termination typeSOLDER HOOK
M300
ENGINEERING DATA SHEET
HERMETICALLY SEALED RELAY
2 PDT/10 AMP
Polarized, non latching hermetically sealed relay
2 PDT
Contact arrangement
Coil supply
Meets the requirements of
Qualified to
Direct current
MIL-R-83536/9 and /10
CECC16101-018
CECC16303-801
PRINCIPLE TECHNICAL CHARACTERISTICS
Contacts rated at
Weight
Dimensions max.
of case in mm
Balanced Force design.
Hermetically sealed, corrosion protected metal can.
APPLICATION NOTES:
001
002
007
023
APPLICABLE SOCKETS:
S300
SC30*
10 Amps / 28 Vdc or 115 Vac -
400 Hz
40 grams max
26 x 25.7 x 13.3
Intrinsically safe relay.
CONTACT ELECTRICAL CHARACTERISTICS
Minimum
operating cycles
100,000 cycles
20,000 cycles
100,000 cycles
100,000 cycles
50 cycles
400,000 cycles
Contact rating per
pole and load type
resistive load
inductive load (L/R=5ms)
motor load
lamp load
resistive overload
at 25% rated resistive load
Load Current in Amps
@28 Vdc
10
8
4
2
40
@115 Vac 400 Hz
10
8
4
2
60
@115/200 Vac 400 Hz 3Ø
10
8
4
2
North America
6900 Orangethorpe Ave.
P.O. Box 5032
Buena Park, CA 90622 USA
Europe, SA
2 Rue Goethe
57430 Sarralbe
France
Tel: (33) 3 87 97 98 97
Fax: (33) 3 87 97 84 04
Asia-Pacific Ltd.
20/F Shing Hing Commercial Bldg.
21-27 Wing Kut Street
Central, Hong Kong
Tel: (852) 2 191 2886
Fax: (852) 2 389 5803
www.leachintl.com
Tel: (01) 714-736-7599
Fax: (01) 714-670-1145
Data sheets are for initial product selection and comparison. Contact Leach International prior to choosing a component.
Date of issue: 9/07
- 101 -
Page 1 of 4
I would like to ask what simulation software can simulate the charging current when there are only capacitors and power switches.
I would like to ask what simulation software can simulate the instantaneous voltage and current when only the capacitor and the power switch are charged. The inductor receives the current change when ...
安_然 Analog electronics
AD8066 amplifier circuit
When AD8066 is connected to +6V, the output waveform is very good and ideal, but when it is connected to +12V power supply, the chip is directly burned out. Why? The power supply range of the chip is ...
zys Analog electronics
Pressure sensor 4-20 mA signal acquisition
1. Directly connect a small resistor in series for AD acquisition 2. Add an op amp for AD acquisition 3. Use an op amp plus a linear optical isolation and then AD acquisition 4. Use max472 current to ...
fhlso Analog electronics
LED Street Lights
Hello everyone! Recently, I have installed several LED street lamps in my company. When I connect the 120W street lamp to the power supply, the street lamp can light up normally, but when I turn off t...
649631964 LED Zone
Why is there a huge difference between the voltage at the non-inverting input and the voltage at the inverting input of my LM201 op amp?
I am making an LDO circuit, which uses the LM201 op amp. In theory, shouldn't the voltages of the two pins of the op amp be basically equal? However, during my experiment, I found that the voltage dif...
husthxh Analog electronics
What is your anti-interference design principle?
Similar to the prevention of influenza A! :lol [b][color=blue]Suppress the interference source, cut off the interference propagation path, and improve the anti-interference performance of sensitive de...
soso MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2431  559  205  332  1270  49  12  5  7  26 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号