5962-8757904XA datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Wireless rf/communication> Telecom circuit> 5962-8757904XA

5962-8757904XA: DescriptionIC DATACOM, MIL-STD-1553 DATA BUS TRANSCEIVER, DIP36, DIP-36, Network Interface; CategoryWireless rf/communication Telecom circuit; File Size231KB，23 Pages; ManufacturerDefense Supply Center Columbus

Download Datasheet Parametric View All

5962-8757904XA Overview

IC DATACOM, MIL-STD-1553 DATA BUS TRANSCEIVER, DIP36, DIP-36, Network Interface

5962-8757904XA Parametric

Parameter Name	Attribute value
Maker	Defense Supply Center Columbus
Parts packaging code	DIP
package instruction	DIP,
Contacts	36
Reach Compliance Code	unknown
JESD-30 code	R-XDIP-P36
length	48.133 mm
Number of functions	2
Number of terminals	36
Package body material	UNSPECIFIED
encapsulated code	DIP
Package shape	RECTANGULAR
Package form	IN-LINE
Certification status	Not Qualified
Filter level	MIL-PRF-38534
Maximum seat height	5.715 mm
surface mount	NO
Telecom integrated circuit types	MIL-STD-1553 DATA BUS TRANSCEIVER
Terminal form	PIN/PEG
Terminal pitch	2.54 mm
Terminal location	DUAL
width	15.24 mm

Preview

Download Datasheet

View All

REVISIONS

LTR

DESCRIPTION

Incorporated NOR's 5962-R110-94 and 5962-R013-96. Made

Changes to table I for device type 07. Redraw entire document.

Inactivate device types 03, 04, and 07 for new design. Add device

type 10.

DATE

(YR-MO-DA)

96-06-20

98-01-28

APPROVED

K.A. Cottongim

K. A. Cottongim

REV

SHEET

REV

SHEET

REV STATUS

OF SHEETS

REV

SHEET

PREPARED BY

Donald R. Osborne

PMIC N/A

STANDARD

MICROCIRCUIT

DRAWING

THIS DRAWING IS AVAILABLE

FOR USE BY ALL

DEPARTMENTS

AND AGENCIES OF THE

DEPARTMENT OF DEFENSE

DEFENSE SUPPLY CENTER COLUMBUS

P. O. BOX 3990

COLUMBUS, OHIO 43216-5000

CHECKED BY

D. A. Dicenzo

APPROVED BY

N. A. Hauck

MICROCIRCUIT, HYBRID, DIGITAL, DUAL CHANNEL, 15

VOLT DRIVER-RECEIVER, RECEIVER IDLE NORMALLY

LOW

DRAWING APPROVAL DATE

87-08-06

SIZE

CAGE CODE

REVISION LEVEL

AMSC N/A

SHEET

67268

5962-87579

DSCC FORM 2233

APR 97

DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.

5962-E067-98

1.4 Recommended operating conditions - Continued.

Driver peak output current (all devices) . . . . . . . . . . . . . . . . . .

Serial data rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Junction temperature (T

(devices 01, 02, 03, 05, 06, 08, 09, and 10) . . . . . . . . . . . . .

(devices 04 and 07) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Case operating temperature range (T

) . . . . . . . . . . . . . . . . . .

2. APPLICABLE DOCUMENTS

2.1 Government specification, standards, and handbook. The following specification, standards, and handbook form a part of

this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the

issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the

solitation.

SPECIFICATION

DEPARTMENT OF DEFENSE

MIL-PRF-38534 - Hybrid Microcircuits, General Specification for.

STANDARDS

DEPARTMENT OF DEFENSE

MIL-STD-883 - Test Methods and Procedures for Microelectronics.

MIL-STD-973 - Configuration Management.

MIL-STD-1835 - Microcircuit Case Outlines.

HANDBOOK

DEPARTMENT OF DEFENSE

MIL-HDBK-780 - Standard Microcircuit Drawings.

MIL-HDBK-1553 - Multiplex Applications Handbook.

(Unless otherwise indicated, copies of the specification, standards, and handbook are available from the Standardization

Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of

this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a

specific exemption has been obtained.

3. REQUIREMENTS

3.1 Item requirements. The individual item performance requirements shall be in accordance with MIL-PRF-38534.

Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturer's

Quality Management (QM) plan or as designated for applicable device class. Therefore, the tests and inspections herein may

not be performed for applicable device class (see MIL-PRF-38534). Futhermore, the manufacturers may take exceptions or use

alternate methods to the tests and inspections herein and not perform them. However, the performance requirements as defined

in MIL-PRF-38534 shall be met for the applicable device class. The modification in the QM plan shall not affect the form, fit, or

function as described herein.

180 mA

1.0 MHz maximum

+150(C

+160(C

-55(C to +125(C

SIZE

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43216-5000

DSCC FORM 2234

APR 97

REVISION LEVEL

5962-87579

SHEET

3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in

MIL-PRF-38534 and herein.

3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 and figure 1 herein.

3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.

3.2.3 Timing waveforms. Timing waveforms shall be as specified on figure 3.

3.2.4 Typical bus connections. Typical bus connections shall be as specified on figure 4.

3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are

as specified in table I and shall apply over the full specified operating temperature range.

3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical

tests for each subgroup are defined in table I.

3.5 Marking of Device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with

the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked as listed in QML-38534.

3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described

herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample,

for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those

which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be

made available to the preparing activity (DSCC-VA) upon request.

3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this

drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturer's product meets

the performance requirements of MIL-PRF-38534 and herein.

3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of

microcircuits delivered to this drawing.

4. QUALITY ASSURANCE PROVISIONS

4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified

in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or

function as described herein.

4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply:

Burn-in test, method 1015 of MIL-STD-883.

(1)

Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level

control and shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit

shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified

in test method 1015 of MIL-STD-883.

T A as specified in accordance with table I of method 1015 of MIL-STD-883.

(2)

Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests

prior to burn-in are optional at the discretion of the manufacturer.

SIZE

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43216-5000

DSCC FORM 2234

APR 97

REVISION LEVEL

5962-87579

SHEET

Recommended Resources

Single channel infrared remote control receiving circuit

Silicon rectifier capacitor energy storage DC system circuit

Class A power amplifier circuit with dynamic bias

half wave rectifier

Telephone line abnormality alarm circuit diagram

13. Power supply circuit diagram of AST MPX-1 color display

Power Supply Design Tips Series: Power supply design tip 1: Choose the correct operating frequency for your power supply By Robert Kollman Texas InstrumentsWelcome to Power Design Tips! With today's emphasis on more efficient, lower ...; 安_然 Analog electronics

The difference between Bluetooth, infrared and wifi, and the ability of radio waves of different frequency bands to penetrate walls and bypass obstacles: Electromagnetic waves are arranged in descending order according to wavelength: radio waves, infrared rays, visible light, ultraviolet rays, X-rays, and gamma rays. The following are several common el...; Aguilera RF/Wirelessly

How to write binary numbers for msp430 (urgent): 0b00001111, why is it not recognized when writing a binary number like this? How should I write it? (This is more intuitive)...; zaq1 Microcontroller MCU

Show the WEBENCH design process + solar cell voltage reduction circuit design with the lowest cost: Use WEBENCH to design the lowest cost circuit design for solar cell step-down. The total BOM cost is $1.21 and the efficiency is 92%. The overall situation is good. Finally, upload the entire design d...; hanskying666 Analogue and Mixed Signal

Photo: Construction photo of a computer room of a road monitoring engineering company (ZT): ...; 绿茶 Industrial Control Electronics

Ask a question about downloading mirrors:: Ask a question about downloading the image: Using dnw5.0, PB4.2, ARM2440 board, can't broadcast Ethernet Boot Loader Configuration: --------------------------------------- 1) IP address: 192.168.1.123...; zhaohepi Embedded System

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components