Physical Layer Transceiver is designed to maximize the speed of
SpaceWire links implemented in Field Programmable Gate
Arrays. The UT200SpWPHY01 is designed to handle the critical
timing issues associated with the SpaceWire data/strobe encoding
scheme.
Receiver Fail-Safe
The UT200SpWPHY01 SpaceWire Physical Layer Transceiver is
a high gain, high speed device that amplifies a small differential
signal (20mV) to TTL logic levels. Due to the high gain and tight
threshold of the receiver, care should be taken to prevent noise
from appearing as a valid signal.
The receiver’s internal fail-safe circuitry is designed to source/
sink a small amount of current, providing fail-safe protection (a
stable known state of HIGH output voltage) for floating,
terminated or shorted receiver inputs.
1.
Open Input Pins.
If an application requires an unused
channel, the inputs should be left OPEN. Do not tie unused
receiver inputs to ground or any other voltages. The input
is biased by internal high value pull up and pull down
resistors to set the output to a HIGH state. This internal
circuitry will guarantee a HIGH, stable output state for
open inputs.
2.
Terminated Input.
If the driver is disconnected (cable
unplugged), or if the driver is in a three-state or power-off
condition, the receiver output will again be in a HIGH state,
even with the end of cable 100Ω termination resistor across
the input pins. The unplugged cable can become a floating
antenna which can pick up noise. If the cable picks up more
than 10mV of differential noise, the receiver may see the
noise as a valid signal and switch. To insure that any noise
is seen as common-mode and not differential, a balanced
interconnect should be used. Twisted pair cable offers
better balance than flat ribbon cable.
Shorted Inputs.
If a fault condition occurs that shorts the receiver
inputs together, thus resulting in a 0V differential input voltage,
the receiver output remains in a HIGH state. Shorted input fail-
safe is not supported across the common-mode range of the device
(V
SS
to 2.4V). It is only supported with inputs shorted and no
external common-mode voltage applied.
2
Table 1
:
SpaceWire Physical Layer Transceiver Device Op-
eration Truth Table
TxOE
0
1
0
0
1
1
1
1
1
RST
0
1
1
1
0
0
1
1
1
LclLBE
X
0
0
1
X
X
0
1
1
RmtLBE
X
0
X
X
0
1
1
0
1
Tx
Outputs
Hi-Z
CMOS
Tx Inputs
Hi-Z
Hi-Z
0
LVDS
Rx Inputs
LVDS
Rx Inputs
CMOS
Tx Inputs
LVDS
Rx Inputs
Rx
Outputs
Hi-Z
LVDS
Rx Inputs
LVDS
Rx Inputs
CMOS
Tx Inputs
Hi-Z
Hi-Z
LVDS
Rx Inputs
CMOS
Tx Inputs
CMOS
Tx Inputs
RADIATION
Parameter
Total Ionizing Dose (TID)
Single Event Latchup (SEL)
1, 2
SEU Saturated Cross-Section (σ
sat
)
Onset Single Event Upset (SEU) LET
Threshold
3
Neutron Fluence
Dose Rate Upset
Dose Rate Survivability
Limit
>3E5
and
1E6
>109
1.0E-8
109
1.0E14
TBD
TBD
Units
rads(Si)
MeV-cm
2
/mg
cm
2
/device
MeV-cm
2
/mg
n/cm
2
rads(Si)/sec
rads(Si)/sec
Notes:
1. The UT200SpW02 are latchup immune to particle LETs >109 MeV-cm
2
/mg.
2. Worst case temperature and voltage of T
C
= +125
o
C, V
DD
= 3.6V,
V
DD
Q1/Q3/Q4 = 3.6V for SEL.
3. Worst case temperature and voltage of T
C
= +25
o
C, V
DD
= 3.0V,
V
DD
Q1/Q3/Q4 = 3.0V for SEU.
4.Adams 90% worst case particle environment, Geosynchronous orbit, 100mils
of Aluminum shielding.
3
28-pin Flatpack Pin Description
Pin Name
LclLBE
Pin
Number
1
Pin Type
LVCMOS Input
1
Description
Local Loopback Enable
0: No loopback, received data comes from LVDS Rx
inputs (RxD+, ...)
1: Local loopback, received data comes from LVCMOS
Tx inputs (TxD0, ...)
Remote Loopback Enable
0: No loopback, Transmit LVDS data comes from the
LVCMOS Tx inputs (TxD0, ...)
1. Remote Loopback, Transmit LVDS data comes from
LVDS Rx inputs.
LVDS Rx differential positive Data input
LVDS Rx differential negative Data input
LVDS Rx differential positive Strobe input
LVDS Rx differential negative Strobe input
VDD 3.3V power supply
Vss 0V
LVDS Output
LVDS Output
LVDS Output
LVDS Output
LVCMOS Input
1
LVDS Tx differential positive Strobe output
LVDS Tx differential negative Strobe output
LVDS Tx differential positive Data output
LVDS Tx differential negative Data output
TxOE=High: Enables LVDS transmit
TxOE=Low: Tri-states LVDS transmit
RmtLBE
2
LVCMOS Input
1
RxD+
RxD-
RxS+
RxS-
V
DD
GND
TxS+
TxS-
TxD+
TxD-
TxOE
RxDR
RxDF
RxClk
RST
TxClk
3
4
5
6
7, 22, 28
8,14,21,27
9
10
11
12
13
26
25
24
23
20
LVDS Input
LVDS Input
LVDS Input
LVDS Input
LVCMOS Output Receiver rising edge (even) bit output (See Figure 7)
LVCMOS Output Receiver falling edge (odd) bit output (See Figure 7)
LVCMOS Output Receiver clock output
LVCMOS Input
1
RST must remain low for 3 clock cycles before
transitioning high, and must transition high 3 clock
cycles before valid data.
Clock input to transmitter used to clock LVDS output.
Any phase relationship is allowed between TxClk &
WrClk but both must come from the same clock source
and TxClk must be twice the frequency of the WrClk.
Transmitter input data Clock used to clock CMOS input
to transmitter. Any phase relationship is allowed between
TxClk & WrClk but both must come from the same clock
source and WrClk must 1/2 of TxClk.
First (even) bit of 2bit parallel strobe input to transmitter
Second (odd) bit of 2bit parallel strobe input to
transmitter
First, even bit of 2bit parallel data input to transmitter
Second, odd bit of 2bit parallel data input to transmitter
4
LVCMOS Input
1
WrClk
19
LVCMOS Input
1
TxS0
TxS1
TxD0
TxD1
18
17
16
15
LVCMOS Input
LVCMOS Input
LVCMOS Input
LVCMOS Input
Note 1. LVTTL compatible
PIN CONFIGURATION
LclLBE
RmtLBE
RxD+
RxD-
RxS+
RxS-
V
DD
GND
TxS+
TxS-
TxD+
TxD-
TxOE
GND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
V
DD
GND
RxDR
RxDF
RxClk
RST
V
DD
GND
TxClk
WrClk
TxS0
TxS1
TxD0
TxD1
ABSOLUTE MAXIMUM RATINGS
1
(Referenced to V
SS
)
SYMBOL
V
DD
V
I/O
PARAMETER
DC supply voltage
Voltage on any pin during operation
Voltage on any LVDS pin during cold
spare
2
T
STG
P
D
Θ
JC
I
I
Storage temperature
Maximum power dissipation
Thermal resistance, junction-to-case
3
DC input current
LIMITS
-0.3 to 4.0V
-0.3 to (V
DD
+ 0.3V)
-.3 to 4.0V
-65 to +150°C
432 mW
10°C/W
±
10mA
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device
at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability and performance.
We choose to use6517AThe electrometer / high resistance meter is the measurement instrument for these test configurations because it offers femtoampere sensitivity and has an integrated programmable 1...
Requirements: One main road and one rural road. They form a crossroad, and the main road is required to be given priority. There are six traffic lights, MR (main red), MY (main yellow), MG (main green...
Define an array in CodeWarrior for ARM Developer Suite: int array name[]＝{}; Isn’t it the same as above? !!! The compilation error is as follows[img]http://hi.eeworld.net/attachment/201002/1/122988_12...
Now the manufacturer has brought a machine with an embedded system installed. After entering the system, it will boot into the opie environment. Using df to check, the result is # /dev/ram 27568 26789...
[font=微软雅黑][size=3]A few days ago, I shared some reference designs with you. For details, please see: [url=https://bbs.eeworld.com.cn/thread-459191-1-1.html]Share some practical reference designs with...
A line scan lens is an industrial lens used with line scan cameras. Its imaging principle is to capture the image of the workpiece using a linear sensor and then perform digital signal processing t...[Details]
In mobile technology, sensors are the primary input for measured signals and form a component of a sensor system. They include sensitive and transducer elements connected to carriers and circuits. ...[Details]
On August 22nd, Lantu Motors unveiled a new technology called "Lanhai Intelligent Hybrid" during a live broadcast of CCTV News' "Top Laboratory." The name sounds like another new term, but a closer...[Details]
Amidst the wave of intelligent automotive transformation, advanced driver assistance is gradually emerging from cutting-edge technology into the mainstream, becoming a new frontier of industry comp...[Details]
Keysight Technologies is combining its electromagnetic simulator with Synopsys' AI-driven RF design migration flow to create an integrated design flow for migrating from TSMC's N6RF+ process techno...[Details]
Charging is a familiar process for new energy vehicles, and as a source of battery energy, charging piles are crucial. New energy vehicle charging can be divided into fast charging and slow chargin...[Details]
UPS stands for Uninterruptible Power Supply, which includes energy storage devices. It is mainly used to provide uninterruptible power supply for devices that require high power stability.
...[Details]
SMT placement machines are important equipment in surface mount technology (Surface Mount Technology). Their performance has a decisive impact on the quality and efficiency of electronic manufactur...[Details]
Plessey Semiconductors has been acquired by Haylo Labs, which was established in March last year with a $100 million, five-year loan from Chinese technology company Goertek.
Haylo Labs w...[Details]
Reflow soldering, as an electronics assembly process, has become a vital component of the electronics manufacturing industry. Choosing reflow soldering equipment is crucial for improving production...[Details]
During daily operation of an R-type power transformer, the voltage used varies as the equipment being used adjusts. This raises the question: can the transformer change voltage at this point? The a...[Details]
Linear motor modules have become the "sweet spot" in various fields due to their advantages such as long stroke, fast speed, high precision, smooth operation and long life. Different models of line...[Details]
On August 20, Geely announced its focus on "One Cockpit". Through a unified AI OS architecture, a unified AI Agent, and a unified user ID, it will achieve an All-in-One AI cockpit, create the first...[Details]
Introduction: In digital circuit calculations, there is no concept of decimal points. You know where the decimal is, but the circuit does not know where the decimal point is. Therefore, you need to...[Details]
The mobile computing market is rapidly evolving, and manufacturers are fiercely competing for market share. A key area of competition is battery life, which encompasses two key aspects: how long th...[Details]
Test/Measurement
京公网安备 11010802033920号
EEWORLD
