5GSR44G-E-100M-FREQ datasheet, PDF

Datasheet> All Categories > Passive components> oscillator> 5GSR44G-E-100M-FREQ

5GSR44G-E-100M-FREQ: DescriptionSine Output Oscillator, 10MHz Min, 30MHz Max, ROHS COMPLIANT, SMD, 4 PIN; CategoryPassive components oscillator; File Size90KB，1 Pages; ManufacturerEuroquartz; Websitehttp://www.euroquartz.co.uk/; Environmental Compliance

Download Datasheet Parametric View All

5GSR44G-E-100M-FREQ Overview

Sine Output Oscillator, 10MHz Min, 30MHz Max, ROHS COMPLIANT, SMD, 4 PIN

5GSR44G-E-100M-FREQ Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	Euroquartz
Reach Compliance Code	compliant
Maximum control voltage	4.5 V
Minimum control voltage	0.5 V
Frequency Adjustment - Mechanical	NO
Frequency offset/pull rate	100 ppm
frequency stability	50%
Installation features	SURFACE MOUNT
Maximum operating frequency	30 MHz
Minimum operating frequency	10 MHz
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
Oscillator type	SINE
Output impedance	10000 Ω
Output level	1 V
physical size	11.4mm x 9.6mm x 4.7mm
Maximum supply voltage	5.25 V
Minimum supply voltage	4.75 V
Nominal supply voltage	5 V
surface mount	YES

Preview

Download Datasheet

View All

EURO

QUARTZ

FEATURES

Sine Wave output VCXO

Output 10k //10pF load, 1.0V p-p

Harmonics < 25dBc

Low current consumption

GSR44 Sine Wave VCXOs

11.4 x 9.6 x 4.7mm SMD Sine Wave VCXO

OUTLINE & DIMENSIONS

DESCRIPTION

GSR44 sine wave VCXOs provide a true sine wave out output. The

VCXOs are packaged in the industry-standard, 4 pad 11.4 x 9.6mm

SMD package. The VCXO is produced to close tolerances and has low

current consumption.

SPECIFICATION

Frequency Range:

Input Voltage:

Frequency Stability:

Control Voltage Centre:

Initial Frequency Accuracy:

Control Voltage Range:

Frequency Deviation Range:

Output Wave Form:

Output Level:

Harmonics:

Phase Noise:

Current Consumption

Supply = 2.8V:

Supply = 3.3V:

Supply = 5.0V:

Start-up Time:

Storage Temperature:

Sub-Harmonics:

Ageing:

Enable/Disable:

RoHS Status:

10.0MHz to 30.0MHz

+2.8V, +3.3V±5% or +5.0VDC ±5%

See table

+2.5 VDC

±15ppm with Conrol V at +2.5VDC

+0.5V to +4.5VDC

±100ppm typical*

True Sine Wave

10k //10pF load, 1.0V p-p

<-25dBc

-130dBc/Hz at 1kHz offset

1.0mA

1.1mA

1.2mA

2.0ms typical

-50° to +125°C

None

±5ppm per year maximum

Not implemented - 4 pad package

Fully compliant or non-compliant

* Wider pulling range available

FREQUENCY STABILITY

Stability Code Stability ±ppm Temp. Range

0°~+70°C

100

0°~+70°C

-40°~+85°C

100

-40°~+85°C

If non-standard frequency stability is required

Use ‘I’ followed by stability, i.e. I20 for ±20ppm

PART NUMBERING

Example:

Supply Voltage

3 = 3.3 Volts

5 = 5.0 Volts

Series Designation

GSR44

RoHS Status

G = compliant

Blank = non-compliant

Frequency Stability

See table

Pull Range

±ppm

Pull Range Code

M = Maximum

N = Minimum

T = Typical

Frequency

MHz

3GSR44G-A-80N-25.000

EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE

Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 Email: info@euroquartz.co.uk www.euroquartz.co.uk

Recommended Resources

Zero trigger switching circuit

Baby house humidity controller circuit

Jiyi doorbell circuit

Low-pass or high-pass filter circuit using BUF-03

Pin functions of HT7603A~HT7603E

MP3 circuit diagram 2

DG128 3×3 matrix scanning need help: I need help with DG128 3×3 matrix scanning. I have a headache these days. How to use pull-up resistors? The 3×3 scanning program has failed many times. I am new here and need help....; quxiangyu NXP MCU

Does analog electrical difference have a big impact on learning microcontrollers? What should I learn when learning microcontrollers?: I am studying measurement and control technology and instruments, and I really want to know what aspects of the knowledge I need to learn as a foundation for single-chip microcomputers. I wonder if an...; bingda Embedded System

Notice on the 2011 National Undergraduate Electronic Design Competition (03.01): [i=s]This post was last edited by paulhyde on 2014-9-15 09:01[/i]Organizing committees of each competition area and relevant colleges and universities:The National Undergraduate Electronic Design Comp...; fish001 Electronics Design Contest

[Help] After turning on the general interrupt in AD interrupt, the stack overflows!!!: There are two interrupts in the program, ADC12 and UART1. It works fine when only one of them is turned on.Both are turned on: ADC is normal, but the interrupt response of UART1 is very slow, and it c...; 冬小麦 Microcontroller MCU

How to return from the interrupt of 51?: I wrote a small experimental program, but I can't return after being interrupted. Could you please help me figure out where the problem is!!! Thanks............. #includeunsigned char Run[] = {0x01, 0...; xingcard Embedded System

Hiring embedded developers, as long as you have written C code for one year and used Linux system, (fresh graduates are also welcome): Since the project is urgent and several kernels have left, we are hiring urgently! The monthly salary is about 4k! Interested parties please send your resume to zhaopin@hltong.cn,...; kedou000007 Linux and Android

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components