EEWORLDEEWORLDEEWORLD

Part Number

Search

50038-5080P

Description
Board Connector, 320 Contact(s), 4 Row(s), Male, Straight, Press Fit Terminal,
CategoryThe connector    The connector   
File Size292KB,2 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

50038-5080P Overview

Board Connector, 320 Contact(s), 4 Row(s), Male, Straight, Press Fit Terminal,

50038-5080P Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid2144513577
Reach Compliance Codecompliant
ECCN codeEAR99
Connector typeBOARD CONNECTOR
Contact to complete cooperationNICKEL PALLADIUM GOLD (30)
Contact completed and terminatedNickel/Palladium/Gold (Ni/Pd/Au)
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
DIN complianceNO
Filter functionNO
IEC complianceNO
JESD-609 codee4
MIL complianceNO
Mixed contactsYES
Installation methodSTRAIGHT
Installation typeBOARD
Number of rows loaded4
OptionsGENERAL PURPOSE
Terminal pitch2.54 mm
Termination typePRESS FIT
Total number of contacts320
Hardware Testing
The power supply can be freely selected. Try to design a frequency of 2KHZ, an output voltage of 12V, and a load current of 1A. The design result should be as close to the requirements of engineering ...
xiaoliu721104 Analog electronics
WINCE BOOTLOADER development and compilation
Dear experts, I am learning Windows CE bootloader development. Currently, I refer to Zhang Dongquan's "Windows CE Practical Development Technology" and Windows CE help files and follow the following s...
shenyu815 Embedded System
Add a network communication module
Let's add a network communication module, so that I can also play a role in switch hardware, hehe...
651076842 Suggestions & Announcements
Regarding the principle of flash ADC, there is a question that I don't understand
As shown in the figure, the flash ADC uses a resistor network to obtain the reference level of the comparator. But why are the resistors on the two sides not R but 1.5R and 0.5R? Doesn't this cause th...
社会实践 Analog electronics
After manually raising the software priority, can interrupts of the same priority level still occur?
When a section of code in my main program is running, I modify the software priority from Level 0 (I1=1, I0=0) to Level 1 (I1=0, I0=1), and set the priority of external port PB1 to Level 1 (I1=0, I0=1...
zyyu stm32/stm8
I just started to learn the basics of single-chip microcomputers! I want to use the C51 single-chip microcomputer to write a program code that can generate a sine wave using the assembly program
I just started to learn the basics of single-chip microcomputers! I want to use the C51 single-chip microcomputer to write a program code that can generate a sine wave using the assembly program...
21999 MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1654  1072  63  747  2216  34  22  2  16  45 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号