Low Phase Noise Divider by 2 VCXO (10MHz to 20MHz)
FEATURES
•
•
•
•
•
•
•
Integrated voltage-controlled crystal oscillator
circuitry (VCXO) (pull range 380ppm minimum).
VCXO tuning range: 0V - V
DD
V.
Uses inexpensive fundamental-mode parallel
resonant crystals (from 20 to 40MHz).
Integrated divider by 2: output range of 10MHz
to 20MHz.
2.5V or 3.3V supply voltage.
Selectable High Drive (30mA) or Standard Drive
(10mA) output.
Available in 8-Pin TSSOP or SOIC.
PIN CONFIGURATION
XOUT
N/C
VCON
GND
1
8
XIN
OE^
VDD
CLK
ABV0252
2
3
4
7
6
5
Note: ^ denotes internal pull up
OUTPUT RANGE
DESCRIPTION
DIVIDER
FREQUENCY
RANGE
10 - 20MHz
OUTPUT
BUFFER
CMOS
The ABV0252 is a monolithic low jitter, high per-
formance CMOS VCXO IC Die. It allows the control
of the output frequency with an input voltage
(VCON), using a low cost crystal.
This makes the ABV0252 ideal for a wide range of
applications requiring a VCXO output in the 10MHz
to 20MHz range, using a fundamental crystal ranging
from 20 to 40 MHz.
÷
2
BLOCK DIAGRAM
X IN
XOUT
XTAL
OSC
C LK
V A R IC A P
OE
VCON
30332 Esperanza., Rancho Santa Margarita, Ca 92688 Ph: 949-546-8000 Fax: 949-546-8001
www.Abracon.com
03/21/05 Page 1
ABV0252
Low Phase Noise Divider by 2 VCXO (10MHz to 20MHz)
PIN DESCRIPTIONS
Name
XOUT
N/C
VCON
GND
CLK
VDD
OE
XIN
Number
1
2
3
4
5
6
7
8
Type
I
-
I
P
O
P
I
I
Description
Crystal output. See Crystal Specifications on page 4.
Not connected.
Voltage Control input.
Ground.
Output clock.
Power supply.
Output enable input. Disables (tri-state) output when low. Internal pull-up
enables output by default if pin is not connected to low.
Crystal input. See Crystal Specifications on page 4.
ELECTRICAL SPECIFICATIONS
1. Absolute Maximum Ratings
PARAMETERS
Supply Voltage
Input Voltage, dc
Output Voltage, dc
Storage Temperature
Ambient Operating Temperature*
Junction Temperature
Lead Temperature (soldering, 10s)
ESD Protection, Human Body Model
SYMBOL
V
DD
V
I
V
O
T
S
T
A
T
J
MIN.
-0.5
-0.5
-65
-40
MAX.
4.6
V
DD
+0.5
V
DD
+0.5
150
85
125
260
2
UNITS
V
V
V
°C
°C
°C
°C
kV
Exposure of the device under conditions beyond the limits specified by Maximum Ratings for extended periods may cause permanent damage to the
device and affect product reliability. These conditions represent a stress rating only, and functional operations of the device at these or any other con-
ditions above the operational limits noted in this specification is not implied.
*
Note:
Operating Temperature is guaranteed by design for all parts (COMMERCIAL and INDUSTRIAL), but tested for COMMERCIAL grade only.
2. DC Electrical Specifications
PARAMETERS
Supply Current, Dynamic, with
Loaded Outputs
Operating Voltage
Output drive current
(High Drive)
Output drive current
(Standard Drive)
Short Circuit Current
VCXO Control Voltage
SYMBOL
I
DD
V
DD
I
OH
I
OL
I
OH
I
OL
VCON
CONDITIONS
F
XIN
= 20 - 52MHz
Output load of 10pF
V
OH
= V
DD
-0.4V, V
DD
=3.3V
V
OL
= 0.4V, V
DD
= 3.3V
V
OH
= V
DD
-0.4V, V
DD
=3.3V
V
OL
= 0.4V, V
DD
= 3.3V
MIN.
TYP.
10
MAX.
UNITS
mA
2.25
30
30
10
10
±50
0
3.63
V
DD
V
mA
mA
mA
mA
mA
V
30332 Esperanza., Rancho Santa Margarita, Ca 92688 Ph: 949-546-8000 Fax: 949-546-8001
www.Abracon.com
03/21/05 Page 2
ABV0252
Low Phase Noise Divider by 2 VCXO (10MHz to 20MHz)
3. AC Electrical Specifications
PARAMETERS
Input Crystal Frequency
Output Clock Rise/Fall Time
(Standard Drive)
Output Clock Rise/Fall Time
(High Drive)
Output Clock Duty Cycle
SYMBOL
CONDITIONS
0.3V ~ 3.0V with 15 pF load
0.3V ~ 3.0V with 15 pF load
Measured @ 50% V
DD
MIN.
20
TYP.
2.4
1.2
MAX.
52
UNITS
MHz
ns
45
50
55
%
4. Voltage Control Crystal Oscillator
PARAMETERS
VCXO Stabilization Time *
VCXO Tuning Range
CLK output pullability
VCXO Tuning Characteristic
Pull range linearity
VCON input impedance
VCON modulation BW
SYMBOL
T
VCXOSTB
CONDITIONS
From power valid
F
XIN
= 20 - 40MHz;
XTAL C
0
/C
1
< 250
0V
≤
VCON
≤
3.3V
VCON=1.65V
±1.65V
MIN.
TYP.
MAX.
10
UNITS
ms
ppm
ppm
ppm/V
%
kΩ
kHz
500
±200
150
10
80
0V
≤
VCON
≤
3.3V, -3dB
25
Note:
Parameters denoted with an asterisk (*) represent nominal characterization data and are not production tested to any specific limits.
5. Jitter Specifications
PARAMETERS
Period jitter RMS
Period jitter peak-to-peak
Integrated jitter RMS
CONDITIONS
20MHz
20MHz
Integrated 12 kHz to 20 MHz at 20MHz
MIN.
TYP.
2.5
20
1
MAX.
UNITS
ps
ps
ps
6. Phase Noise Specifications
PARAMETERS
Phase Noise relative
to carrier
FREQUENCY
20MHz
@10Hz
-65
@100Hz
-90
@1kHz
-120
@10kHz
-140
@100kHz
-147
UNITS
dBc/Hz
Note: Phase Noise at VCON = 0V – to be measured
30332 Esperanza., Rancho Santa Margarita, Ca 92688 Ph: 949-546-8000 Fax: 949-546-8001
www.Abracon.com
03/21/05 Page 3
ABV0252
Low Phase Noise Divider by 2 VCXO (10MHz to 20MHz)
7. Crystal Specifications
PARAMETERS
Crystal Resonator Frequency
Crystal Loading Rating
Crystal Pullability
Recommended ESR
SYMBOL
F
XIN
C
L (xtal)
C
0
/C
1 (xtal)
R
E
CONDITIONS
Parallel Fundamental Mode
At Vcon = 1.65V
AT cut
AT cut
MIN.
20
TYP.
MAX.
40
UNITS
MHz
pF
9.5
250
30
-
Ω
Note:
Crystal Loading rating: 9.5pF is the loading the crystal sees from the VCXO chip at VCON = 1.65V. It is assumed that the crystal will be at nomi-
nal frequency at this load. If the crystal requires more load to be at nominal frequency, the additional load must be added externally.
This however may reduce the pull range.
PACKAGE INFORMATION
8 PIN ( dimensions in mm )
Narrow SOIC
Symbol
A
A1
B
C
D
E
H
L
e
Min.
1.47
0.10
0.33
0.19
4.80
3.80
5.80
0.38
Max.
1.73
0.25
0.51
0.25
4.95
4.00
6.20
1.27
1.27 BSC
Min.
-
0.05
0.19
0.09
2.90
4.30
6.20
0.45
TSSOP
Max.
1.20
0.15
0.30
0.20
3.10
4.50
6.60
0.75
0.65 BSC
A1
B
e
C
L
A
D
E
H
30332 Esperanza., Rancho Santa Margarita, Ca 92688 Ph: 949-546-8000 Fax: 949-546-8001
www.Abracon.com
03/21/05 Page 4
ABV0252
Low Phase Noise Divider by 2 VCXO (10MHz to 20MHz)
ORDERING INFORMATION
For part ordering, please contact our Sales Department:
30332 Esperanza., Rancho Santa Margarita, Ca 92688
Ph: 949-546-8000 Fax: 949-546-8001
PART NUMBER
The order number for this device is a combination of the following:
Device number, Package type and Operating temperature range
ABV0252 (H) X C
PART NUMBER
TEMPERATURE
C=COMMERCIAL
I=INDUSTRAL
PACKAGE TYPE
O=TSSOP , S=SOIC
Optional High Drive
Order Number
ABV0252OC-T
ABV0252OC
ABV0252HOC-T
ABV0252HOC
ABV0252SC-T
ABV0252SC
ABV0252HSC-T
ABV0252HSC
Marking
ABV0252OC
ABV0252OC
ABV0252HOC
ABV0252HOC
ABV0252SC
ABV0252SC
ABV0252HSC
ABV0252HSC
Package Option
TSSOP - Tape and Reel
TSSOP – Tube
TSSOP - Tape and Reel
TSSOP - Tube
SOIC
SOIC
SOIC
SOIC
-
-
-
-
Tape and Reel
Tube
Tape and Reel
Tube
Abracon Corporation, reserves the right to make changes in its products or specifications, or both at any time without notice. The information fur-
nished by Abracon is believed to be accurate and reliable. However, Abracon makes no guarantee or warranty concerning the accuracy of said infor-
mation and shall not be responsible for any loss or damage of whatever nature resulting from the use of, or reliance upon this product.
LIFE SUPPORT POLICY:
Abracon’s products are not authorized for use as critical components in life support devices or systems without the express
written approval of the President of Abracon Corporation.
30332 Esperanza., Rancho Santa Margarita, Ca 92688 Ph: 949-546-8000 Fax: 949-546-8001
I would like to ask you: In the battery management, there is a sampling program, which reads and writes by operating AC97 (not through AD??). The program is as follows: BOOL Battery_sampleADC(DWORD *s...
[i=s]This post was last edited by qwqwqw2088 on 2014-3-17 08:55[/i] [p=20, null, left][color=rgb(51, 51, 51)]1. How to understand the voltage of an inductor and the self-electromotive force of an indu...
The project requires a rechargeable battery with 220V AC input and 5V 5A output (preferably with adjustable voltage). The size and weight should not be too large and the battery life should be about o...
Hello everyone! I have a question that is a bit high-level, haha. China imported about 230 billion US dollars of integrated circuits in 2013 and about 240 billion US dollars in 2014. I would like to k...
Why does my program stop running after a while or stops at a distance after it is downloaded to the board?
#include stm32f10x_lib.h #include "sys.h" #include "usart.h" #include "delay.h" #include "led...
In early 2002, I started to write a working program for an IC card prepaid electricity meter. The meter used Philips' 8-bit 51-expanded single-chip microcomputer
87LPC764
, and wa...[Details]
In
circuit design,
current
measurement
is widely used, and the main fields are divided into three categories: in measurement,
the electric meter
is used to measure the curre...[Details]
Google's driverless technology is not only an eye-catching technology, but also a subversion of the car usage model.
Those who have watched anti-terrorism films and TV dramas must have been im...[Details]
The Portable Digital Data Acquisition System (PDDAS) uses LabVIEW Real-Time and PXI to control the wind tunnel test and record air pressure data from 128 different channels.
"The LabVIEW Real-...[Details]
My colleague and I spent the day chatting in the hotel bar. We had met with several customers. We were both wondering how come these engineers we were meeting knew almost nothing about analog techn...[Details]
This paper establishes a fuel cell engine test platform based on the NI integrated hardware and software environment. This platform can realize the test and control of fuel cell engines and their a...[Details]
Overview
As a remote network communication control method with advanced technology, high reliability, complete functions and reasonable cost, CAN-bus has been widely used in various automa...[Details]
In the analysis of electronic circuits, static analysis (also known as DC analysis) is the basis of circuit analysis. However, it is well known that electronic components are nonlinear, so the anal...[Details]
RS-422 and RS-485 are both serial data interface standards, which were developed and published by the Electronic Industries Association (EIA). RS-422 defines a balanced communication interface with a ...[Details]
Problems such as the depletion of natural resources, air pollution, traffic congestion, and rising fossil fuel prices have forced societies and individuals to seek alternative means of transportati...[Details]
Motors, especially those with brushes, generate a lot of noise. This noise must be dealt with if the appliance is to meet the requirements of EMC standards. The means to solve EMC are nothing more ...[Details]
Describe how to meet the challenges of complexity with a modern wiring design toolset. Option codes and expressions can simulate the variables of an automotive project. A full-featured tool suite c...[Details]
This article will introduce a design method for a distributed control system used in a tracking car, which can perform distributed control of motor modules, sensor modules, and lighting control mod...[Details]
1 Introduction to LED
With the development of science and technology, people have higher and higher requirements on automobile light sources. LED (Light Emitting Diode) has gradually attracted...[Details]
LED is the abbreviation of the English word. Its main meanings are: LED = Light Emitting Diode, a solid-state semiconductor device that can convert electrical energy into visible light. It can dire...[Details]