EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-7S2FA424N

Description
Transponder, 10709Mbps(Tx), 10709Mbps(Rx), FC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-7S2FA424N Overview

Transponder, 10709Mbps(Tx), 10709Mbps(Rx), FC/UPC Connector,

PH1-7S2FA424N Parametric

Parameter NameAttribute value
MakerJDS Uniphase Corporation ( VIAVI )
Reach Compliance Codeunknown
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body width56.1 mm
body height13.2 mm
Body length or diameter76.5 mm
Communication standardsGR-253
Connection TypeFC/UPC CONNECTOR
Data rate (receive)10709 Mbps
Data rate (send)10709 Mbps
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1561 nm
Nominal optical power output0.562 mW
minimum return loss-27 dB
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
How to convert a rectangular wave into a sine wave
How to convert a rectangular wave into a sine wave?...
宋宋 Test/Measurement
"Modern High Frequency Switching Power Supply Practical Technology" by Liu Shengli
[font=微软雅黑][size=4][color=#666666] [/color][/size][/font] [color=#666666][font=微软雅黑][size=4] [/size][/font][/color] [font=微软雅黑][size=4][b][Brief Introduction] [/b][/size][/font] [font=微软雅黑][size=4] [/...
linjiang Download Centre
Proteus simulation error
I did a small experiment with PIC16F676 and wrote a small program. It runs fine on the board, but it fails to simulate on Proteus7.7. There is no response at all. I don't know why?Program function: Co...
flyfinger Microchip MCU
Why does the inductor squeak?
I made a power supply with MC34063A, input 12v, output 5v. Normal working current 200MA, maximum current 700MA. The inductor used is 220uH inductor. The rated current of the inductor is 2A. I also pai...
heshue Power technology
27M remote control car distance interference
[size=4]1. First of all, both the transmitting and receiving modules were bought from Taobao. As shown in the picture [/size][img=750,585]https://img.alicdn.com/imgextra/i4/66569494/TB2onMsgVXXXXb7XpX...
秦时明月2017 RF/Wirelessly
51 microcontroller interrupts the problem of serial communication.
[code] What's wrong with this code? How to change it? /*Interrupt to realize serial communication*/ #include unsigned char flag; void main() { void init(); init(); while(1) { while(!flag) ; ES = 0; P1...
weilaidaozhu Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1848  2345  142  271  612  38  48  3  6  13 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号