EEWORLDEEWORLDEEWORLD

Part Number

Search

PK30PS-50-3E

Description
Single Phase EMI Filter, 250V, 50/60HzHz,
CategoryAnalog mixed-signal IC    filter   
File Size467KB,3 Pages
ManufacturerPower Dynamics, Inc.
Websitehttp://www.powerdynamics.com/
Environmental Compliance  
Download Datasheet Parametric View All

PK30PS-50-3E Overview

Single Phase EMI Filter, 250V, 50/60HzHz,

PK30PS-50-3E Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerPower Dynamics, Inc.
Reach Compliance Codecompliant
Other featuresINDUCTANCE 0.3 MILLI HENRY
CertificationUL; VDE
filter typeSINGLE PHASE EMI FILTER
maximum frequency10 MHz
minimum frequency0.15 MHz
high30 mm
high potential2250 V
Insertion loss@maximum frequency49 dB
Insertion loss@frequency-min.2 dB
Maximum leakage current0.45 mA
length70.9 mm
Manufacturer's serial numberPK
Installation typePANEL MOUNT
working frequency50/60Hz Hz
Maximum operating temperature85 °C
Minimum operating temperature-25 °C
physical sizeL70.9XB46.5XH30.0 (mm)/L2.791XB1.831XH1.181 (inch)
Rated current30 A
Rated voltage250 V
PK Series
CHASSIS MOUNT, HIGH PERFORMANCE, MULTIPURPOSE,
SINGLE STAGE EMI/RFI LINE FILTER.
MECHANICAL DIMENSIONS
(Unit: mm)
A1, A2, A3
C
A
2x 4.8
D
B
E
10.0
G
DIMENSIONS
CASE
CODE A
B
C
F
D
E
G
24.4 45.0 17.5 64.5 54.1 8.5 49.6
A1
33.8 45.0 30.0 64.5 54.5 14.9 59.0
A2
46.5 51.8 30.0 70.9 60.9 14.9 71.7
A3
F
FEATURES
51.5
The PK series offers a wide variety of EMI filters in numerous
styles of packages and current ratings. The filters are effective
in reducing both Line-to-Line and Line-to-Ground noise up to
30 Amp at 250VAC. This series offers very low leakage
current suitable for medical and non-medical applications.
These filters are also available for Medical applications.
The absence of C(y) capacitors offers extremely low leakage
current to comply with various industry standards especially
the medical equipment with Switching power supplies.
A Bleeder resistor can also be added to prevent excessive
voltages from developing across the filter capacitors when
there is no load.
B1
85.3
74.7
64.0
39.1
2x
4.8
(14.9)
(4.6)
APPLICATIONS
Computer & networking equipment, Measuring & control
equipment, Data processing equipment, laboratory instruments,
Switching power supplies, other electronic equipment.
G1
100.0
82.5
TECHNICAL DATA
Rated Voltage: 115/250VAC
Rated Current: 1A, 2A, 3A, 5A, 6A, 10A, 15A, 20A, 30A
Power Line Frequency: 50/60Hz
Max. Leakage Current each
Line to Ground:
@ 115VAC 60Hz: 0.25mA
@ 250VAC 50Hz: 0.45mA
@ 115VAC 60Hz: 2
µ
A*
@ 250VAC 50Hz: 5
µ
A*
Hipot Rating (one minute)
Line to Ground: 2250VDC
Line to Line: 1450VDC
Temperature Range: -25C to +85C
* Medical application
105.0
95.3
86.4
38.6
4X 6.5X4.0
50.8
(17.3)
(6.1)
Specifications subject to change without notice. Dimensions (mm).
36
145 Algonquin Parkway, Whippany, NJ 07981 • 973-560-0019 • FAX: 973-560-0076
e-mail: filtersales@powerdynamics.com •
www.powerdynamics.com
【MXCHIP Open1081】Use Bootloader to download WIFI_Driver
After reading the manual, I started to figure out how to use this development board. Now I use SSCOM to download the driver to the board. 1. Connect the computer to the serial port of the board. 2. Op...
dontium RF/Wirelessly
Reward for experts to design low power AVR GPRS solution
If you are not an expert, please do not disturb me! Because this solution is to be used for products, please be aware of it. Function: Collect a pulse signal (passive) on site for accumulation, and th...
dita1983 MCU
bash:tftp:command not found
I installed TFTP and configured it, but the error "bash: tftp: command not found" still appears....
slamdunk Embedded System
About LM317T constant current circuit
As shown in the figure above, the constant current circuit on the LM317T DATASHEET, the circuit board I built according to the figure above is not constant current. The voltage across R2 is not 1.25V,...
xh2008email Analog electronics
Brothers who have purchased the Friendly Arm mini2440 in group purchase, please help me
My goal is to download the code directly to SDRAM for debugging. I did it this way: write a piece of code less than 4K to initialize the clock, watchdog, interrupt, stack and set the parameters of SDR...
a1z26 Embedded System
What is the difference between high frequency circuit and radio frequency circuit?
[size=4]Introduction to high-frequency circuits[/size] [size=4] To put it simply, high-frequency circuits are radio circuits, but they do not involve microwave circuits (microwaves are used to process...
Aguilera Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1075  2496  1513  591  1147  22  51  31  12  24 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号