Operating Temperature Range ..........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Bump Reflow Temperature (Note 1) ................................+235°C
Note 1:
The MAX6477–MAX6484 are constructed using a unique set of packaging techniques that impose a limit on the thermal pro-
file the devices can be exposed to during board-level solder attach and rework. This limit permits only the use of the solder
profiles recommended in the industry-standard specification, JEDEC 020A, paragraph 7.6, Table 3 for IR/VPR and
Convection reflow. Pre-heating is required. Hand or wave soldering is not allowed.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V
IN
= (V
OUT
+ 0.5V) or +2.5V, whichever is greater, C
OUT
= 3.3µF, T
A
= -40°C to +85°C. Typical specifications are at T
A
= +25°C,
unless otherwise noted.) (Note 2)
PARAMETER
Input Voltage Range
Input Undervoltage Lockout
Supply Current (Ground Current)
Shutdown Supply Current
REGULATOR CIRCUIT
Output Current
Output Voltage Accuracy (Fixed
Output Voltage Operation,
Table 1) MAX6469–MAX6476
Output Voltage Accuracy (Fixed
Output Voltage Operation,
Table 1) MAX6477–MAX6484
Adjustable Output Voltage Range
SET Reference Voltage
SET Dual Mode
TM
Threshold
SET Input Leakage Current
1mA
≤
I
OUT
≤
150mA, T
A
= +25°C
1mA
≤
I
OUT
≤
150mA, T
A
= -40°C to +85°C
1mA
≤
I
OUT
≤
300mA, T
A
= -40°C to +85°C
2mA
≤
I
OUT
≤
100mA, T
A
= +25°C
2mA
≤
I
OUT
≤
100mA, T
A
= -40°C to +85°C
2mA
≤
I
OUT
≤
300mA, T
A
= -40°C to +85°C
(Note 3)
V
SET
I
SET
V
SET
= 0, +1.2V (Note 3)
SYMBOL
V
IN
V
UVLO
I
Q
I
SHDN
V
IN
falling
I
OUT
= 0
I
OUT
= 300mA
T
A
= +25°C
300
-1.3
-2.3
-2.7
-1.1
-2.0
-2.5
V
SET
1.200
CONDITIONS
MIN
2.5
2.25
82
96
0.1
TYP
MAX
5.5
2.47
136
1
UNITS
V
V
µA
µA
mA
+1.3
+2.3
+2.7
+1.1
+2.0
+2.5
5.0
1.258
±100
V
V
mV
nA
%
%
1.229
185
±20
Dual Mode is a trademark of Maxim Integrated Products, Inc.
U1A is powered by positive power, U2A is powered by negative power, Input-signal is the input signal, the signal is positive and negative, the frequency is lower than 1K, and the amplitude meets the i...
How to use the MSP430G22553 chip to design and make a pulse signal tester that can measure the amplitude, frequency, period, duty cycle, rise and fall time and other parameters of the pulse signal. Ca...
The temperature sensor on my board does not have a pull-up resistor and displays as follows: The temperature sensor on my board does nothave a pull-up resistor and displays as follows:I would like to ...
[font=Hiragino Sans GB W3, Hiragino Sans GB, Arial, Helvetica, simsun, u5b8bu4f53][size=3][color=#473b34]Given β=100, what is Vce=? [/color][/size][/font]...
[i=s]This post was last edited by paulhyde on 2014-9-15 09:44[/i] The Higher Education Press & Xilinx Competition Tianjin Division will start on Saturday, and the competition time is from 8 am to 4 pm...
Today's computer peripherals are pursuing high speed and high versatility. In order to meet user needs, seven companies led by Intel launched the USB (Universal Serial Bus) bus protocol in 1994, wh...[Details]
Microchip's PIC18F46J50 is a low-power, high-performance 8-bit USB microcontroller (MCU) using nanoWatt XLP technology. The current in deep sleep mode can be as low as 13nA, the operating voltage i...[Details]
1. Introduction
This design was made for participating in an electronic design competition. It effectively solved the problem of the operation and control of an electric car on a seesaw. The s...[Details]
With the advent of increasingly powerful processors, image sensors, memory, and other semiconductor devices, as well as the algorithms that enable them, computer vision can be implemented in a wide...[Details]
Two simple circuits are implemented to drive two LEDs from a battery powered microprocessor.
This design is based on a circuit that uses three resistors and a microprocessor I/O pin as an input h...[Details]
The solidification and modularization of intelligent video analysis algorithms are the current trends in the application of intelligent video analysis technology. It perfectly combines intelligent ...[Details]
With the rapid development of urban economy, elevators are increasingly used as a vertical transportation tool. However, elevator fault detection and maintenance, especially the role of elevator remot...[Details]
From the PIC16F946 datasheet, we know that there are two ways to write values to the LCD for display:
1. Directly write the value to LCDDATA1~LCDDATA23
2. Use disconnect t...[Details]
Microcalorimetry
is used to determine energy relationships. Microcalorimetry techniques are often required when performing calorimetric experiments with small sample sizes or slow heating rat...[Details]
LED is the abbreviation of light emitting diode, which is an electric light source made of semiconductor technology. The core part of LED is a chip composed of P-type semiconductor and N-type semi...[Details]
In recent years, with the rapid development of the information industry, dot matrix LED display screens have been widely used in various advertising and information display systems such as the fina...[Details]
As people's requirements for safety and comfort in the process of driving cars continue to increase, automotive radars are widely used in the car's adaptive cruise system, collision avoidance syste...[Details]
Today, the value of electronic components in cars accounts for 15-20% of the total vehicle. In the future, this proportion may be as high as 30-40% as more safety electronics, fuel consumption and ...[Details]
It is well known to automotive suppliers that automakers are demanding more from their supply base. For connector suppliers, this means stricter requirements for product performance, stability and ...[Details]
The era of mobile access to the Internet has arrived, and it will rapidly change the business and infrastructure needs of mobile operators under a whole new trend of requirements. We need 4G LTE to...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
