EEWORLDEEWORLDEEWORLD

Part Number

Search

51761-30013613AB

Description
Board Connector, 149 Contact(s), 4 Row(s), Female, Right Angle, Solder Terminal, Receptacle
CategoryThe connector    The connector   
File Size254KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

51761-30013613AB Overview

Board Connector, 149 Contact(s), 4 Row(s), Female, Right Angle, Solder Terminal, Receptacle

51761-30013613AB Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
MakerAmphenol
Reach Compliance Codecompliant
Other featuresTERMINAL PITCH FOR POWER CONTACTS: 6.35 MM
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD (30) OVER NICKEL (50)
Contact completed and terminatedGOLD (5) OVER NICKEL (50)
Contact point genderFEMALE
Contact materialCOPPER ALLOY
DIN complianceNO
Filter functionNO
IEC complianceNO
JESD-609 codee4
MIL complianceNO
Manufacturer's serial number51761
Mixed contactsYES
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of rows loaded4
OptionsGENERAL PURPOSE
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts149
UL Flammability Code94V-0
PDM: Rev:P
STATUS:
Released
Printed: Mar 22, 2011
.
How to simulate waveform in ise13.1
As the title says, I'm learning about Xilinx's FPGA recently, but the ISE software is really confusing. There is no testwave form. How can I use testbench for simulation? Or is there modesilm? I've be...
子诺如歌 FPGA/CPLD
LTIB Introduction and Installation (Part 2)
Supportspreconfigswhich allow developers to store different system configurations (e.g. toolchain selection, kernel selection, package selection etc).Supportsprofilesthis allows just the userspace pac...
bluehacker NXP MCU
How to use an operational amplifier as an attenuator?
[size=6]Hello masters[/size]:congratulate:[size=6]How to use an operational amplifier to make an attenuator[/size]:time:[size=6]? [/size] [size=6]The initial condition is a 0-5v DC voltage, which need...
flying510 Integrated technical exchanges
STM32F207 USB HOST Power
Problem description: Using the STM32F207 official website USB Host msc lib V2.0.1 library, the PHY is embedded internally, so the HOST is FS. The simulation found that when running the red font part o...
punpun stm32/stm8
EVC simple question
This question is really shocking. For many people, this is a very stupid question. But it is very difficult for me, a novice in application, and I don’t know how to start. I found some information on ...
chris1031 Embedded System
[Raspberry Pi Pico Review] ADC External Benchmark vs. Onboard Benchmark
[i=s]This post was last edited by 1nnocent on 2021-3-30 09:05[/i]Last time, three sets of external voltages were measured using ADC0 and the onboard reference voltage, https://bbs.eeworld.com.cn/forum...
1nnocent DIY/Open Source Hardware

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 913  1589  759  1549  1167  19  32  16  24  20 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号