2200GAG300923KB datasheet, PDF

2200GAG300923KB: DescriptionStrain Guage Sensor, Absolute, 0Psi Min, 300Psi Max, 0.15%, 0.20-10.20V, Cylindrical; CategoryThe sensor Sensor/transducer; File Size507KB，4 Pages; ManufacturerGems Sensors & Controls

Download Datasheet Parametric View All

2200GAG300923KB Overview

Strain Guage Sensor, Absolute, 0Psi Min, 300Psi Max, 0.15%, 0.20-10.20V, Cylindrical

Parameter Name	Attribute value
Is it Rohs certified?	incompatible
Reach Compliance Code	unknow
Maximum accuracy(%)	0.15%
shell	STAINLESS STEEL
Nominal offset	0.20V
Maximum operating temperature	80 °C
Minimum operating temperature	-20 °C
Output range	0.20-10.20V
Output type	ANALOG VOLTAGE
Package Shape/Form	CYLINDRICAL
port type	G1/8 FEMALE
Maximum pressure range	300 Psi
Minimum pressure range
Pressure sensing mode	ABSOLUTE
Sensor/Transducer Type	PRESSURE SENSOR,STRAIN GUAGE
Maximum supply voltage	35 V
Minimum supply voltage	1.5 V
Termination type	PLASTIC CABLE GLAND
Base Number Matches	1

Ask about the ARM_GPIO pull-up resistor problem: I would like to ask you, in addition to enhancing the driving capability, the function of the GPIO pull-up resistor is to set the GPIO to input state. When the product is subjected to a high temperatu...; garybaso ARM Technology

Failure characteristics of electronic components: Although there are a large number of electronic components inside electrical equipment, their failures follow certain patterns....; fighting PCB Design

PSpice Classic Chinese Tutorial: The general PSpice classic Chinese tutorial is a good material for beginners. However, the examples given are relatively simple, so I will just give you some ideas....; linda_xia Microchip MCU

【Ask TI】LM3S Series LMLINK: According to the configuration on the ZLG website, LMLINK uses IAR When I switched to keil, I couldn't use LMlink Is the LMlink light flashing different from the IAR driver?...; 常见泽1 Microcontroller MCU

Is the port in high impedance state after STM32 reset?: I used STM32F103C6T6, and added a buffer chip 74LV07 through a port to drive the optocoupler at a low level. I found that sometimes the load of the optocoupler was turned on during the power-on proces...; zhangjmxx stm32/stm8

In an AC circuit, what is the phase relationship between the voltage across R and the current flowing through the inductor?: I would like to ask a question here. In an AC circuit, what is the phase relationship between the voltage across R and the current flowing through the inductor? eeworldpostqq...; 蓝猫淘气 Analog electronics

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components