Model the Gate Charge, Transient, and Diode Reverse Recovery
Characteristics
DESCRIPTION
The attached spice model describes the typical electrical
characteristics of the n-channel vertical DMOS. The subcircuit
model is extracted and optimized over the
−55
to 125°C
temperature ranges under the pulsed 0-V to 10-V gate drive. The
saturated output impedance is best fit at the gate bias near the
threshold voltage.
A novel gate-to-drain feedback capacitance network is used to model
the gate charge characteristics while avoiding convergence difficulties
of the switched C
gd
model. All model parameter values are optimized
to provide a best fit to the measured electrical data and are not
intended as an exact physical interpretation of the device.
SUBCIRCUIT MODEL SCHEMATIC
This document is intended as a SPICE modeling guideline and does not constitute a commercial product data sheet. Designers should refer to the appropriate
data sheet of the same number for guaranteed specification limits.
Document Number: 70114
S-71544Rev. B, 30-Jul-07
www.vishay.com
1
SPICE Device Model SUM85N03-06P
Vishay Siliconix
SPECIFICATIONS (T
J
= 25°C UNLESS OTHERWISE NOTED)
Parameter
Static
Gate Threshold Voltage
On-State Drain Current
a
a
Symbol
Test Condition
Simulated
Data
1.8
923
0.0044
0.008
0.0077
0.89
Measured
Data
Unit
V
GS(th)
I
D(on)
V
DS
= V
GS
, I
D
= 250
µA
V
DS
= 5 V, V
GS
= 10 V
V
GS
= 10 V, I
D
= 20 A
V
A
0.0053
Ω
0.0078
1.2
V
Drain-Source On-State Resistance
r
DS(on)
V
GS
= 10 V, I
D
= 20 A, T
J
= 125°C
V
GS
= 4.5 V, I
D
= 20 A
Forward Voltage
a
V
SD
I
S
= 100 A, V
GS
= 0 V
Dynamic
b
Input Capacitance
Output Capacitance
Reverse Transfer Capacitance
Total Gate Charge
c
Gate-Source Charge
Gate-Drain Charge
c
Turn-On Delay Time
Rise Time
c
c
c
C
iss
C
oss
C
rss
Q
g
Q
gs
Q
gd
t
d(on)
t
r
t
d(off)
t
f
t
rr
I
F
= 50 A, di/dt = 100 A/µs
V
DD
= 15 V, R
L
= 0.30
Ω
I
D
≅
50 A, V
GEN
= 10 V, R
G
= 2.5
Ω
V
DS
= 15 V, V
GS
= 10 V, I
D
= 50 A
V
GS
= 0 V, V
DS
= 25 V, f = 1 MHz
3135
509
177
47
10
7.5
10
14
26
33
31
3100
565
255
48
10
7.5
12
12
30
10
35
ns
nC
pF
Turn-Off Delay Time
c
Fall Time
c
Source-Drain Reverse Recovery Time
Notes
a. Pulse test; pulse width
≤
300
µs,
duty cycle
≤
2%.
b. Guaranteed by design, not subject to production testing.
c. Independent of operating temperature.
www.vishay.com
2
Document Number: 70114
S-71544Rev. B, 30-Jul-07
SPICE Device Model SUM85N03-06P
Vishay Siliconix
COMPARISON OF MODEL WITH MEASURED DATA (T
J
=25°C UNLESS OTHERWISE NOTED)
Document Number: 70114
S-71544Rev. B, 30-Jul-07
www.vishay.com
3
Legal Disclaimer Notice
Vishay
Disclaimer
All product specifications and data are subject to change without notice.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf
(collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein
or in any other disclosure relating to any product.
Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any
information provided herein to the maximum extent permitted by law. The product specifications do not expand or
otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed
therein, which apply to these products.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this
document or by any conduct of Vishay.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless
otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such
applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting
from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding
products designed for such applications.
Product names and markings noted herein may be trademarks of their respective owners.
1. LED
1.1 Introduction to LED
LED (Light Emitting Diode) is the abbreviation of light-emitting diode. LED is a very common lighting device in life. There are many types of LED in our lives, as shown ...
[color=rgb(85, 85, 85)][backcolor=rgb(255, 255, 255)]I looked it up and found that it is available online, but the points are too expensive, and it takes time to register and earn points, and now real...
[i=s]This post was last edited by dcexpert on 2015-1-26 14:58[/i] I haven't had much time in the past two weeks because of some things. It's the end of the year, and maybe everyone is like this. I sti...
Hardware: ppc860 + 10/100M network card Software: vxworks There is a 64kbps * 32-channel voice stream to be sent and received through this device. Can the voice packets be sent and received smoothly?...
Multi-bullet automatic navigation radiofrequency technology for tumor treatment 1. Principle: Use heating to kill tumor cells. Because tumor cells are more sensitive to heating than normal tissues, t...
New energy pure electric vehicles generally accelerate faster than comparable fuel-powered vehicles, both from a standing start and while accelerating. Many believe this is simply due to the motor'...[Details]
In recent years, with the application of the IEC61850 standard and the development and deployment of optoelectronic transformers, the concept of digital substations has been put into practical use ...[Details]
Logic analyzers are widely used tools in digital design verification and debugging. They can verify the proper functioning of digital circuits and help users identify and troubleshoot faults. They ...[Details]
For healthcare professionals, accurate diagnosis and treatment are crucial for a clear picture of a person's health. However, healthcare professionals often rely on tests at medical facilities, cli...[Details]
Gross profit margin jumped from 13.6% in the first half of last year to 25.9%, almost doubling year-on-year.
On August 21, RoboSense released its interim performance report, in which the...[Details]
On August 22, South Korean media Nate reported on the 20th local time that Samsung Electronics is introducing Hyper Cell technology into its most advanced 2nm process technology, striving to improv...[Details]
Laird Thermal Systems has introduced the HiTemp ET series Peltier cooler modules, which can operate at high temperatures and provide on-site cooling for sensitive electronic devices.
Dig...[Details]
Through AI connection technology supported by Qualcomm X85 5G modem and RF and Qualcomm FastConnect 7900 mobile connection system, seamless switching can be achieved between cellular net...[Details]
PowiGaN achieves 95% efficiency at both light and full loads, meeting critical operational and safety requirements.
DARWIN, Australia and SAN JOSE, Calif.,
August 22, 2025 – Powe...[Details]
With the prevalence of online conferencing, live streaming, and voice communication in gaming, high-quality audio input devices are becoming increasingly important. To this end, XMOS, an expert in ...[Details]
Most cameras on the market use chips manufactured by Japanese companies like Sony, Sharp, Panasonic, and LG. South Korea now has the capability to produce chips, but the quality is somewhat inferio...[Details]
introduction
A common voltage regulator is a three-terminal one. Its function is to step down the voltage and stabilize it at a fixed output value. Voltage regulators are commonly available in...[Details]
Since the beginning of the 21st century, with the rapid development of my country's urban and rural economies and the improvement of people's living standards, more and more people have begun to ow...[Details]
The automotive driveshaft is a crucial connecting component in the automotive mechanical system. It is a circular component that allows for connection or assembly, as well as movement and rotation....[Details]
This article uses the Allwinner T507 quad-core automotive-grade processor as the development board. This article explains how to configure Ethernet for the T507 development board. Other boards may ...[Details]