3068-004-3103 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > The connector> The connector> 3068-004-3103

3068-004-3103: DescriptionBoard Connector, 4 Contact(s), 1 Row(s), Male, Right Angle, 0.156 inch Pitch, Solder Terminal, Natural Insulator, Receptacle; CategoryThe connector The connector; File Size173KB，1 Pages; ManufacturerMethode Electronics Inc.

Download Datasheet Parametric View All

3068-004-3103 Overview

Board Connector, 4 Contact(s), 1 Row(s), Male, Right Angle, 0.156 inch Pitch, Solder Terminal, Natural Insulator, Receptacle

3068-004-3103 Parametric

Parameter Name	Attribute value
Maker	Methode Electronics Inc.
Reach Compliance Code	unknown
ECCN code	EAR99
Other features	WITH LEGS
body width	0.41 inch
subject depth	0.45 inch
body length	0.618 inch
Body/casing type	RECEPTACLE
Connector type	BOARD CONNECTOR
Contact to complete cooperation	AU ON NI
Contact completed and terminated	TIN OVER NICKEL
Contact point gender	MALE
Contact material	BRASS
contact mode	RECTANGULAR
Contact resistance	5 mΩ
Contact style	SQ PIN-SKT
Dielectric withstand voltage	1500VAC V
maximum insertion force	LIF N
Insulation resistance	500000000000 Ω
Insulator color	NATURAL
insulator material	NYLON
Manufacturer's serial number	3000
Plug contact pitch	0.156 inch
Installation method	RIGHT ANGLE
Installation type	BOARD
Number of connectors	ONE
PCB row number	1
Number of rows loaded	1
Maximum operating temperature	105 °C
Minimum operating temperature	-40 °C
PCB contact pattern	RECTANGULAR
Plating thickness	20u inch
Rated current (signal)	7 A
Guideline	UL, CSA
reliability	COMMERCIAL
Terminal length	0.156 inch
Terminal pitch	3.9624 mm
Termination type	SOLDER
Total number of contacts	4
Evacuation force-minimum value	LIF N

Preview

Download Datasheet

View All

.156” (3.96mm)

Through Hole Right Angle Connector

3000 SERIES “TERMACON”

PART NUMBER LEGEND

30XX-XXX-XXXX

CONTACT TAIL DIMS (SEE TABLE 2)

CONTACT MATERIAL (SEE NOTE 1)

OPTIONS

2 - HIGH INSERTION FORCE CONTACT

3 - LOW INSERTION FORCE CONTACT

NO. OF POSITONS (SEE TABLE 1)

OPTIONS

WITH LEGS

WITH HOOKS

WITH HOOKS AND LOCKING RAMP

WITH LOCKING RAMP

WITH HOOKS, LOCKING RAMP AND POLARIZING KEY

WITHOUT HOOKS, W/ LOCKING RAMP AND POLARIZING KEY

CONTACT FINISH (SEE NOTE 2)

INSULATOR MATERIAL (SEE NOTE 1)

MATING HEADERS: 3100 SERIES

POLARIZING KEY &

LOCKING RAMP

LEG

HOOK

Connector Products

1700 Hicks Road • Rolling Meadows, IL 60008 USA

Telephone: 847.392.3500 • Fax: 847.392.9404

email: mcpsales@methode.com • Web Page: www.methode.com

Recommended Resources

Simple signal generator for signal tracing

Low power FM FM transmitter circuit

Delay door opening circuit

Complementary dimming circuit

Internal wiring diagram of GA series IGBT single switch module

Sequential parking circuit for two electric motors

[PSoC4 experience] First experience: I just wrote a serial port program according to the manual. I don't know if you followed the manual. There is one thing that is inconsistent with the manual screenshot, that is, the Name of the module...; lcofjp MCU

Does anyone have the 800 parallel port driver software?: Help, I have an old rf1800 editor with a parallel port connected to the printer, but it doesn't work. I downloaded several USB drivers, and I need to manage the program for the AT27C1024 microcontroll...; 吴信圣 Microchip MCU

How to determine the pulse width of a four-phase stepper motor driven by a single-chip microcomputer?: [i=s]This post was last edited by paulhyde on 2014-9-15 03:42[/i] How to determine the pulse width of a four-phase stepper motor driven by a single-chip microcomputer?I use a six-wire four-phase stepp...; liu5013 Electronics Design Contest

561 Development Board: 1. Standard configuration of motherboard hardware 1. BF561SKBCZ-5A (17by17) (can provide loose chips for customers in urgent need) 2. SDRAM: 64M 3. NOR FLASH: 16M, SPI FLASH, can jumper to choose to b...; lengxing Embedded System

Help with STM32 clock initialization issue: I am a novice, just starting with STM32. I want to understand the clock initialization. I want to set it by directly operating the register first. After understanding the register, I will use the libr...; wx837078933 stm32/stm8

How to evenly place GND vias on heat sink pads: RT, how to go from Figure 1 to Figure 2? I have tried to select all GND Via --> Component Placement and use alignment, but it doesn't work. Thanks for your advice if you know....; dirty PCB Design

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components