EEWORLDEEWORLDEEWORLD

Part Number

Search

E2SDA18-23.040M

Description
QUARTZ CRYSTAL RESONATOR, 23.04MHz, ROHS COMPLIANT, RESISTANCE WELDED, SMD, 2 PIN
CategoryPassive components    Crystal/resonator   
File Size139KB,4 Pages
ManufacturerECLIPTEK
Websitehttp://www.ecliptek.com
Environmental Compliance  
Download Datasheet Parametric Compare View All

E2SDA18-23.040M Overview

QUARTZ CRYSTAL RESONATOR, 23.04MHz, ROHS COMPLIANT, RESISTANCE WELDED, SMD, 2 PIN

E2SDA18-23.040M Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerECLIPTEK
package instructionROHS COMPLIANT, RESISTANCE WELDED, SMD, 2 PIN
Reach Compliance Codecompliant
Other featuresAT-CUT CRYSTAL; BULK
Ageing5 PPM/YEAR
Crystal/Resonator TypePARALLEL - FUNDAMENTAL
Drive level1000 µW
frequency stability0.005%
frequency tolerance30 ppm
JESD-609 codee3
load capacitance18 pF
Installation featuresSURFACE MOUNT
Nominal operating frequency23.04 MHz
Maximum operating temperature70 °C
Minimum operating temperature
physical sizeL13.3XB4.85XH4.5 (mm)/L0.524XB0.191XH0.177 (inch)
Series resistance50 Ω
surface mountYES
Terminal surfaceMatte Tin (Sn) - with Nickel (Ni) barrier

E2SDA18-23.040M Preview

E2SDA18-23.040M
Series
RoHS Compliant (Pb-free) Resistance Welded
HC-49/UP SMD Crystal
Frequency Tolerance/Stability
±30ppm at 25°C, ±50ppm over 0°C to +70°C
Mode of Operation
AT-Cut Fundamental
RoHS
Pb
E2S D A 18 -23.040M
Nominal Frequency
23.040MHz
Load Capacitance
18pF Parallel Resonant
ELECTRICAL SPECIFICATIONS
Nominal Frequency
Frequency Tolerance/Stability
Aging at 25°C
Load Capacitance
Shunt Capacitance (C0)
Equivalent Series Resistance
Mode of Operation
Drive Level
Storage Temperature Range
Insulation Resistance
23.040MHz
±30ppm at 25°C, ±50ppm over 0°C to +70°C
±5ppm/year Maximum
18pF Parallel Resonant
7pF Maximum
50 Ohms Maximum
AT-Cut Fundamental
1mWatt Maximum
-40°C to +125°C
500 Megaohms Minimum at 100Vdc
ENVIRONMENTAL & MECHANICAL SPECIFICATIONS
Fine Leak Test
Gross Leak Test
Lead Termination
Mechanical Shock
Resistance to Soldering Heat
Resistance to Solvents
Solderability
Temperature Cycling
Vibration
MIL-STD-883, Method 1014 Condition A
MIL-STD-883, Method 1014 Condition C
Sn 2µm - 6µm
MIL-STD-202, Method 213 Condition C
MIL-STD-202, Method 210
MIL-STD-202, Method 215
MIL-STD-883, Method 2003
MIL-STD-883, Method 1010
MIL-STD-883, Method 2007 Condition A
MECHANICAL DIMENSIONS (all dimensions in millimeters)
LINE MARKING
1
4.50
MAX
E23.040M
E=Ecliptek Designator
M=MHz
13.30 MAX
4.85
MAX
4.88 ±0.20
0.50 MIN (x2)
0.80 ±0.30 (x2)
11.60 MAX
NOTE: Coplanarity 0.360 MAX
www.ecliptek.com | Specification Subject to Change Without Notice | Rev F 2/16/2010 | Page 1 of 4
E2SDA18-23.040M
Suggested Solder Pad Layout
All Dimensions in Millimeters
5.5 (X2)
2.0 (X2)
4.0
Solder Land
(X2)
All Tolerances are ±0.1
www.ecliptek.com | Specification Subject to Change Without Notice | Rev F 2/16/2010 | Page 2 of 4
E2SDA18-23.040M
Recommended Solder Reflow Methods
T
P
Critical Zone
T
L
to T
P
Ramp-up
Ramp-down
Temperature (T)
T
L
T
S
Max
T
S
Min
t
S
Preheat
t 25°C to Peak
t
L
t
P
Time (t)
High Temperature Infrared/Convection
T
S
MAX to T
L
(Ramp-up Rate)
Preheat
- Temperature Minimum (T
S
MIN)
- Temperature Typical (T
S
TYP)
- Temperature Maximum (T
S
MAX)
- Time (t
S
MIN)
Ramp-up Rate (T
L
to T
P
)
Time Maintained Above:
- Temperature (T
L
)
- Time (t
L
)
Peak Temperature (T
P
)
Target Peak Temperature (T
P
Target)
Time within 5°C of actual peak (t
p
)
Ramp-down Rate
Time 25°C to Peak Temperature (t)
Moisture Sensitivity Level
3°C/second Maximum
150°C
175°C
200°C
60 - 180 Seconds
3°C/second Maximum
217°C
60 - 150 Seconds
260°C Maximum for 10 Seconds Maximum
250°C +0/-5°C
20 - 40 seconds
6°C/second Maximum
8 minutes Maximum
Level 1
www.ecliptek.com | Specification Subject to Change Without Notice | Rev F 2/16/2010 | Page 3 of 4
E2SDA18-23.040M
Recommended Solder Reflow Methods
T
P
Critical Zone
T
L
to T
P
Ramp-up
Ramp-down
Temperature (T)
T
L
T
S
Max
T
S
Min
t
S
Preheat
t 25°C to Peak
t
L
t
P
Time (t)
Low Temperature Infrared/Convection 245°C
T
S
MAX to T
L
(Ramp-up Rate)
Preheat
- Temperature Minimum (T
S
MIN)
- Temperature Typical (T
S
TYP)
- Temperature Maximum (T
S
MAX)
- Time (t
S
MIN)
Ramp-up Rate (T
L
to T
P
)
Time Maintained Above:
- Temperature (T
L
)
- Time (t
L
)
Peak Temperature (T
P
)
Target Peak Temperature (T
P
Target)
Time within 5°C of actual peak (t
p
)
Ramp-down Rate
Time 25°C to Peak Temperature (t)
Moisture Sensitivity Level
5°C/second Maximum
N/A
150°C
N/A
30 - 60 Seconds
5°C/second Maximum
150°C
200 Seconds Maximum
245°C Maximum
245°C Maximum 2 Times / 230°C Maximum 1 Time
10 seconds Maximum 2 Times / 80 seconds Maximum 1 Time
5°C/second Maximum
N/A
Level 1
Low Temperature Manual Soldering
185°C Maximum for 10 seconds Maximum, 2 times Maximum.
High Temperature Manual Soldering
260°C Maximum for 5 seconds Maximum, 2 times Maximum.
www.ecliptek.com | Specification Subject to Change Without Notice | Rev F 2/16/2010 | Page 4 of 4

E2SDA18-23.040M Related Products

E2SDA18-23.040M E2SDA18-23.040M TR
Description QUARTZ CRYSTAL RESONATOR, 23.04MHz, ROHS COMPLIANT, RESISTANCE WELDED, SMD, 2 PIN CRYSTALS 30/50 0+70 18PF 23.040MHZ ATCUT FUND HC-49/UP
Is it lead-free? Lead free Lead free
Is it Rohs certified? conform to conform to
Reach Compliance Code compliant unknown
Homemade RF Scanner
Friends who are engaged in RF circuits should all know what a frequency sweeper is used for. I like to make radios, and I often need to adjust the LC loop parameters and filter bandwidth. In order to ...
mrf245 RF/Wirelessly
Get the relevant information required by the Bone Vibration Sensor LIS25BA contestants (including official information and engineers' evaluation)
Participants who obtain the Bone Vibration Sensor LIS25BA can get started faster by following the information below:1. Official bone vibration sensor LIS25BA information Click here to enter (including...
nmg ST MEMS Sensor Creative Design Competition
Wince driver problem
I want to use the common IO port or interrupt port of arm to receive a series of digital signals, store the signals and process them. I am using arm2410. How can I program with evc under wince? How ca...
10317E Embedded System
Question + How to draw images when drawing PCB in Altium Designer
[size=4]How to draw images when drawing PCB in Altium Designer? As shown below, how to draw the following image? [/size]...
hjl240 PCB Design
EEWORLD University ---- Bluetooth Technology Alliance Bluetooth Developer Studio series usage video (Chinese version)
Bluetooth SIG Bluetooth Developer Studio series usage videos (Chinese version) : https://training.eeworld.com.cn/course/2326...
RichCastle RF/Wirelessly
Why is there no response when the serial port debugging assistant sends data to the microcontroller?
I tried to connect VB to the MCU. I burned the following program to the MCU, but it didn't respond. I suspected that VB was wrong. I changed the serial port debugging assistant and sent AA. But it sti...
luxiaoyu_sdc Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 329  1046  237  1836  64  7  22  5  37  2 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号