The Ortel PONA 2100 Series Erbium Doped Fiber Amplifier (EDFA)
is an ideal building block for OEM system integrators. The family of
PONA 2100 series EDFAs is designed to meet the most demanding
noise performance requirements of CATV applications, and
performs all the functions required of an optical amplifier for system
integration. PONA 2100 series EDFAs provide optical isolation on
the input and output of the gain block for stable, low noise operation.
The input and output optical signal power levels are detected for
monitoring and control. The input optical signal is amplified with
active gain control for a constant output power level, or with active
output power control for constant gain mode.
The PONA 2100
series EDFAs also provide monitors and associated alarms for all
vital characteristics. The optical output of the PONA 2100 series
EDFAs can be split into multiple ports by an optional external
splitter.
For more information on this and other products:
Contact Sales at Ortel 626-293-3400, or visit www.ortel.com.
PONA 2100 Series EDFA
Rev B
DATA SHEET
|
FEBRUARY 2006
Optical / Electrical Characteristics
PROPERTY
Product Code
PERFORMANCE
Operating Input Power
Operating Input Power
Output Power
Noise Figure
(Note 2)
Pin
(dBm)
Pin
(dBm)
Po(dBm)
NF (dB)
NF (dB)
NF (dB)
Static Gain Flatness
Dynamic Gain Flatness
(Note 4)
GF (dB)
(dB)
(dB)
(dB)
Output Power Stability
Power Consumption
(steady state regime)
Notes
:
1.
2.
3.
4.
5.
(dB)
Psys(W)
Typ/Max
Typ/Max
Typ/Max
Max
Max
Max
Max
Max
Max
Max
Min
12
-10
14
+/-.25
4.5/5.0
4.0/4.5
4.0/4.5
+/-0.5
+/-1.0
+/-0.5
+/-0.5
+/- 0.1
5
12
-10
17
+/- .25
4.5/5.0
4.0/4.5
4.0/4.5
+/-0.5
+/-1.25
+/-0.5
+/-0.5
+/- 0.1
7
12
-10
20
+/- .25
4.5/5.0
4.0/4.5
4.0/4.5
+/-0.5
+/-1.5
+/-1.0
+/-1.0
+/- 0.1
9
12
-10
22
+/- .25
4.5/5.0
4.0/4.5
4.0/4.5
+/-0.5
+/-2.0
+/-1.0
+/-1.0
+/- 0.1
12
12
-10
24
+/- .25
5.0/5.5
4.5/5.0
4.5/5.0
+/-0.5
+/-2.0
+/-1.0
+/-1.0
+/- 0.1
20
12
-10
26
+/- .25
5.0/5.5
4.5/5.0
N/A
+/-0.5
+/-2.0
N/A
N/A
+/- 0.1
27
12
-10
27
+/- .25
5.0/5.5
4.5/5.0
N/A
+/-0.5
+/-2.0
N/A
N/A
+/- 0.1
32
Nominal
-00 and -01 versions
-02 version
-03 version
(Note 3)
-00 and -02 versions
-01 version
-03 version
(Note 5)
50 C Case
o
UNIT
LIMIT
2114
2117
PONA MODELS
2120
2122
2124
2126
2127
COMMENTS
(note 1)
Unless stated otherwise all specifications apply over the full temperature range and humidity
Measured with 8 evenly spread signals @ 25°C,
Σ
Pin = 0 dBm.
Measured with a swept Probe Signal (Pp), where Pp = 0 dBm @ 25°C
Measured with a swept Probe Signal (Pp), and a fixed Tone Signal (Pt) @ 1545 nm; (Pt = Pp+20 dB; Pt + Pp = 0 dBm) @ 25°C; Gain
Flattened Option with
∆G
= +/-0.5dB is available for some Models
Stability over polarization and temperature
General and Mechanical Specifications
PROPERTY
GENERAL
Operating Wavelength
Operating Case Temperature
Storage Temperature
Operating Humidity
Voltage Supply Range
Optical Connectors
Dimensions In Inches
REQUIREMENT
1530 ~ 1562nm
0°C to 50°C
-40°C to 85°C
20% to 85%
85 VAC to 265 VAC 50/60 Hz
-36 to –60 V DC
SC/APC; SC/UPC; FC/APC;
FC/UPC; E2000/APC
19.0”W x 14.76”D x 1.72”H
Non-condensing
Standard
Optional
User Specified
19’’ Rack Mounted, 1U
Standard
COMMENTS
Ortel, a division of EMCORE
2 of 4
PONA 2100 Series EDFA
Rev B
DATA SHEET
|
FEBRUARY 2006
Outline Drawing
AC and DC versions shown below with 8-port option
DC Version
AC Version
Ortel, a division of EMCORE
3 of 4
PONA 2100 Series EDFA
Rev B
DATA SHEET
|
FEBRUARY 2006
Compliance Information
89/336/EEC Electromagnetic Compatibility Directive, amended by 92/31/EEC & 93/68/EEC
73/23/EEC Low Voltage Directive, amended by 93/68/EEC
EN 50083-2, (2001)
Cable networks for TV signals, sounds and interactive services, Part 2 Electromagnetic
Compatibility for equipment.
EN 55013
EN 61000-3-2
EN 55020
EN 61000-4-6
EN 61000-4-3
EN 61000-4-2
EN 61000-4-4
EN 60950
EN 60825-1
EN 60825-2
CDRH
Mains Conducted Emissions
Mains Frequency and its Harmonics, Conducted Emissions
Radiation from Active Equipment, Radiated Immunity
Immunity of Active Equipment, Radiated Immunity
Immunity of Active Equipment, Radiated Immunity
Electrostatic Discharge Immunity
Electrical Fast Transient / Burst Immunity
Low Voltage Directives
Laser Safety Requirement
Laser Safety Requirement
Laser Safety Requirement
Ordering Information
PONA21
-
-
-
-
Optical
Output
Power
14
- 14 dBm
17
- 17 dBm
20
- 20 dBm
22
- 22 dBm
24
- 24 dBm
26
- 26 dBm
27
- 27 dBm
Output
Ports
1
2
4
8
Input Voltage
AC
– 90-260V 50/60 Hz
DC
– - 48 V
SC
FC
EC
TC
GC
Connector
-
-
-
-
-
SC/APC
FC/APC
E2000/APC
SC/UPC
FC/UPC
GFF/ NF options
00 - Standard
01 - Standard with Gain Flattened option
02 - Standard with Low NF option
03 - Low NF and Gain Flattened
Note: The maximum number of output ports when using E2000 connectors is four. All other optical connectors allow for
the eight ports option
Example:
PONA2120-2-AC-SC-00:
Standard 20 dBm EDFA with AC Power Supply, two (2) optical outputs, and SC/APC optical connectors
Information contained herein is deemed to be reliable and accurate as of issue date. EMCORE reserves the right to change the design or specifications of
the product at any time without notice. Ortel, the Ortel logo, EMCORE, and the EMCORE logo are trademarks of EMCORE Corporation.
[i=s] This post was last edited by paulhyde on 2014-9-15 03:40 [/i] I am so depressed. I didn’t pass the CET-4 with a score of 417. I studied English every day last semester and still ended up like th...
I have encountered this situation several times. The simulation function is fine with modelsim, and the program is not complicated, but after burning it to the board, the function cannot be realized! ...
You will never learn without hands-on experience, and you will never improve without learning theories. The master will lead you to the door, and you must practice on your own. The problem is solved o...
Why is the address offset set to 4 bits? Because it has 20 address buses and the registers are 16 bits, so: 20-16=4? Then the 32-bit processor has a 32-bit address bus and a 32-bit register. Does it h...
International Solar Photovoltaic Network News: Chinese inverter company Sungrow announced that it will build a 3GW photovoltaic inverter manufacturing plant in Bangalore, the capital of Karnataka, ...[Details]
1. Problem When developing STM32 with IAR, I found that I could not print floating point numbers by redirecting printf to the serial port. The code is as follows: The output is as follows: It can...[Details]
For STM32, there are two ways to reset the software: 1) Use the official software library The system reset function is directly provided in the stm32f10x_nvic.c file of the official software li...[Details]
After searching a lot of information, I finally understood the time base timer. I did not use any library functions but operated the registers directly. The following introduces the systick in STM32...[Details]
China Energy Storage Network:
Blockchain + finance, blockchain + environmental protection, blockchain + insurance, even a roadside fried chicken shop is using the banner of blockchain + fried...[Details]
Development Background: 1. Main chip - STM32F207VCT6; 2. TCP/IP protocol stack - LWIP, transplanted based on ST routines; 3. Operating system - none (bare metal); Anomalies: 1. Power on the device wi...[Details]
Serial Port: 一. USART_ITConfig(USART1, USART_IT_TXE, ENABLE): As long as the transmit register is empty, there will always be an interrupt. Therefore, if you are not sending data, turn off the tran...[Details]
With the implementation of the first version of the NR sub-6GHz draft of 3GPP in December 2017, and the subsequent Phase 2 drafts, semiconductor manufacturers and terminal manufacturers began to ...[Details]
What is SYSTICK: This is a 24-bit system tick timer, SysTick, with automatic reload and overflow interrupt functions. All microcontrollers based on the Cortex_M3 processor can obtain a certain time ...[Details]
As cryptocurrency continues to gain popularity, a technology hidden behind it has attracted more attention from the world, that is the now hotly debated
blockchain
. Let's follow the embedd...[Details]
In recent years, in addition to Huawei Kirin
chips
in the mobile phone industry
, Xiaomi's own processor Pengpai S1, AI
chip
start-ups such as Cambrian, Horizon, and Deephi Technolo...[Details]
Mobile communication resale business means that enterprises can contract part of the communication network usage rights from basic telecommunications operators, repackage them into their own brands...[Details]
Photovoltaic inverters are the core equipment of photovoltaic systems. Their main function is to convert the direct current generated by photovoltaic modules into alternating current that meets the...[Details]
Independent watchdog (IWDG) and low power mode are often used in STM32 development. The watchdog is to detect and solve faults caused by software errors, and the low power mode is to enter sleep mode...[Details]
At this exhibition, Microsoft brought its flagship intelligent voice products - XiaoIce and Xiaona. In addition, the voice will be equipped with an intelligent face recognition system. Let's see ho...[Details]
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
