EEWORLDEEWORLDEEWORLD

Part Number

Search

800-011-07C10-26HN

Description
Circular Connector, 26 Contact(s), Aluminum Alloy, Female, Crimp Terminal, Receptacle,
CategoryThe connector    The connector   
File Size214KB,4 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Environmental Compliance  
Download Datasheet Parametric View All

800-011-07C10-26HN Overview

Circular Connector, 26 Contact(s), Aluminum Alloy, Female, Crimp Terminal, Receptacle,

800-011-07C10-26HN Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerGlenair
Reach Compliance Codecompliant
Other featuresPOLARIZED
Back shell typeSOLID
Body/casing typeRECEPTACLE
Connector typeCIRCULAR CONNECTOR
Contact to complete cooperationNOT SPECIFIED
Contact point genderFEMALE
Contact materialNOT SPECIFIED
Coupling typeTHREADED
DIN complianceNO
empty shellNO
Filter functionNO
IEC complianceNO
MIL complianceNO
Plug informationMULTIPLE MATING PARTS AVAILABLE
Mixed contactsNO
Installation typeCABLE AND PANEL
OptionsGENERAL PURPOSE
Shell surfaceANODIZED BLACK
Shell materialALUMINUM ALLOY
Housing size10
Termination typeCRIMP
Total number of contacts26
A
B
C
In-Line
Rear Panel Jam Nut Mount
Square Flange Mount
D
E
F
G
H
J
K
L
M
© 2007 Glenair, Inc.
CAGE Code 06324
Printed in U.S.A.
Series 800
Series 800 “Mighty Mouse”
Original UNF Threaded Coupling
Series 800 Receptacles – Crimp Termination
Integral Band Platform
for direct attachment of a cable
shield using a
BAND-IT®
strap. Install a boot, or overmold
onto the band platform. An accessory thread is available
for attaching strain reliefs and backshells.
Three Shell Options:
Jam nut with o-ring for rear panel
mounting, square flange or in-line receptacle for free-hanging
cables.
HOW TO ORDER
Sample Part Number
80 0- 0 11
Series
-0 1
Shell Style
M
Shell Material /
Finish
C
6-4
Shell Size- Insert
Arrangement
3 #23 Contacts
1 #16 Contact
4 #23 Contacts
7 #23 Contacts
1 #12 Contacts
10 #23 Contacts
13 #23 Contacts
4 #16 Contacts
19 #23 Contacts
26 #23 Contacts
2 #12 Contacts
37 #23 Contacts
P
Contact Type
Standard #23 contacts
accept #22 through
#28 AWG wire. Use the
following contact codes
to specify these contacts:
N
Shell Key
Position
N
Normal
-01
In-Line
800-010
Receptacle with
Banding Platform
-02
Square Flange
for Front or Rear
Mounting
5-3
Aluminum / Black
6-1
Anodize
6-4
M
6-7
Aluminum / Electroless
7-1
Nickel
7-10
NF
8-13
Aluminum / Cadmium
9-4
with Olive Drab
9-19
Chromate
10-26
ZN
12-2
Aluminum / Zinc-
Nickel with Olive Drab
Chromate
12-37
X
Pos. X
P
Pin
Y
Pos. Y
S
Socket
Special contacts for
#26 to #30 AWG are
also available. Use the
following contact codes
to specify these contacts:
Z
Pos. Z
800-011
Receptacle with
Accessory Thread
ZNU
Aluminum / Zinc-Nickel
with Black Chromate
-07
Jam Nut for Rear
Panel Mounting
#23 contacts are packaged
with connectors. #16 and #12
contacts must be ordered
separately.
G
Pin
Z1
Stainless Steel /
Passivated
H
Socket
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
www.glenair.com
C-6
Rev. 05-APR-2007
E-Mail: sales@glenair.com
Analysis of the voltage following circuit of the operational amplifier
The voltage following circuit of the op amp, as shown in Figure 1, uses virtual short and virtual open circuits. It looks simple and clear at first glance, and there is not much to pay attention to. T...
Jacktang Analogue and Mixed Signal
Any ideas for frequency compensation circuit?
...
xiao_pang Analog electronics
Special-shaped board, irregular board stamp hole paneling method
Special-shaped board, irregular board stamp hole assembly method...
luoxiao1116 PCB Design
I want the interface circuit diagram between the microcontroller and the speaker (not the buzzer). How to drive it? Is the programming method the same as that of the buzzer?
I want the interface circuit diagram of the microcontroller and the speaker (not the buzzer). How to drive it? Is the program writing the same as the buzzer? I want to make a small music box, but the ...
紫遥violet 51mcu
About Ethernet interrupt processing function
As the title says! Why in the stellar_interrupt() function, the receive and send queues are processed only when data is received? Why does the send queue rely on receiving data to process it?...
历史的天空 Microcontroller MCU
My embarrassing story——Transvestite series
I was very depressed that I was still treated as a girl until I was in my 20s: (The following events are arranged in chronological order: 1. When I was in high school, I accompanied my mother to the m...
richiefang Talking

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1287  1896  851  1112  2192  26  39  18  23  45 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号