EEWORLDEEWORLDEEWORLD

Part Number

Search

KB16MKW01B05A

Description
0.4VA maximum 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A 20mV ~ 28V)
File Size447KB,13 Pages
ManufacturerNKK
Websitehttps://www.nkkswitches.com.cn
Download Datasheet View All

KB16MKW01B05A Overview

0.4VA maximum 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A 20mV ~ 28V)

Series KB
Toggles
Miniature Pushbuttons
General
Specifications
Electrical Capacity (Resistive Load)
Power Level (silver):
Logic Level (gold):
1A @ 125/250V AC or 1A @ 30V DC
0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
Pushbuttons
Rockers
Other Ratings
Programmable
Illuminated PB
D
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Nominal Operating Force:
Contact Timing:
Travel:
Keylocks
50 milliohms maximum
1,000 megohms minimum @ 500V DC
For Silver: 1,000V AC minimum between contacts for 1 minute minimum &
1,500V AC minimum between contacts & case for 1 minute minimum;
For Gold: 750V AC minimum between contacts for 1 minute minimum &
1,500V AC minimum between contacts & case for 1 minute minimum
100,000 operations minimum
50,000 operations minimum for silver; 100,000 operations minimum for gold
Single pole 0.98 ~ 2.45N for maintained & 0.98 ~ 1.96N for momentary;
Double pole 1.47 ~ 3.43N for maintained & 1.47 ~ 2.94N for momentary
Nonshorting (break-before-make)
Pretravel .087” (2.2mm); Overtravel .031” (0.8mm); Total Travel .118” (3.0mm)
Materials & Finishes
Slides
Housing:
Movable Contactor:
Stationary Contacts:
Housing Base:
Terminal Base:
Common Terminals:
End Terminals:
Lamp Terminals:
Polyamide (UL94V-0)
Silver for power circuit; copper with gold plating for logic level circuit
Silver for power circuit; copper with gold plating for logic level circuit
Polyamide (UL94V-0)
Polyester
Phosphor bronze with silver flash plating for power circuit;
Phosphor bronze with gold flash plating for logic level circuit
Brass with silver flash plating for power circuit;
Brass with gold flash plating for logic level circuit
Phosphor bronze with nickel flash plating
Tactiles
Rotaries
Environmental Data
Operating Temperature Range:
Humidity:
Vibration:
Shock:
–25°C through +50°C (–13°F through +122°F) for Illuminated
–25°C through +70°C (–13°F through +158°F) for Nonilluminated
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s
2
) acceleration (tested in 6 right angled directions, with 3 shocks in each direction)
Touch
Tilt
Installation
Indicators
Mounting Torque:
Cap Installation Force:
Soldering Time & Temperature:
0.78Nm (6.9 lb
in) maximum
4.51N (1.0 lbf) maximum downward force on cap
Manual Soldering: See Profile A in Supplement section.
Standards & Certifications
Accessories
Flammability Standards:
UL:
Supplement
CSA:
UL94V-0 housing & housing base
File No. E44145
Single & double pole models recognized at 1A @ 125/250V AC, 1A @ 30V DC, & 0.4VA @ 28V DC.
Add “/U” to end of part number to order UL mark on switch.
Add “/CUL” to end of part number to order cULus mark on switch.
File No. 023535_0_000
Single & double pole models recognized at 1A @ 125/250V AC, 1A @ 30V DC, & 0.4VA @ 28V DC.
Add “/C” to end of part number to order CSA mark on switch.
www.nkk.com
D22
JZC-23F relay
Another question: What kind of transistor is used to drive this relay? How to explain the words "10A/28VDC, 5A/220VAC, DC5V" on it? It has no requirements for the pull-in current?...
liweiliang MCU
stm32 uses external interrupt
I guess it's a firmware library problem again, as shown in the following figureAn error occurred when setting the channel according to the user manual. I would like to ask how to set the external inte...
dj狂人 stm32/stm8
The boost actual circuit waveform is quite different from the simulation
The following figure shows the simulation schematic diagram and simulation waveform of the boost circuit, which is built using PSIM software. The inductor parameters are 4mH, the capacitor is 10uF, th...
Lsonhealth Power technology
Question about current amplifier
I would like to ask what the load current and load voltage in the book Circuit Design Based on Arithmetic Units and Analog Integrated Circuits mean. I can't understand why the simulation results I got...
sunboy25 Analog electronics
Usage of 52 single chip microcomputer T2
As we all know, the 52 MCU has one more T2 timer than the 51. The car I recently built needs three timers, so T2 also comes in handy. It seems that there is not much information about T2. I read a boo...
五加一等于六 51mcu
How to send data packets larger than 255Bytes using CC131
Generally speaking, CC1310 uses common commands: CMD_PROP_TX, CMD_PROP_RX to send and receive data, and these two commands limit the data length to 255 bytes. If the customer has more than 255 bytes o...
Aguilera Wireless Connectivity

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2074  142  2148  543  2625  42  3  44  11  53 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号