EEWORLDEEWORLDEEWORLD

Part Number

Search

51760-10411209BBLF

Description
Board Connector, Female, Right Angle, Press Fit Terminal, Guide Pin, Receptacle
CategoryThe connector    The connector   
File Size259KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

51760-10411209BBLF Overview

Board Connector, Female, Right Angle, Press Fit Terminal, Guide Pin, Receptacle

51760-10411209BBLF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerAmphenol
Reach Compliance Codecompliant
Board mount optionsHOLE .138-.163
body width0.47 inch
subject depth0.865 inch
body length6.7 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact completed and terminatedTIN
Contact point genderFEMALE
Contact materialCOPPER ALLOY
Contact resistance20 mΩ
Contact styleHYBRID
Dielectric withstand voltage2500VDC V
Durability200 Cycles
maximum insertion force.973 N
Insulation resistance500000000 Ω
insulator materialGLASS FILLED THERMOPLASTIC
Manufacturer's serial number51760
Mixed contactsYES
Installation option 1GUIDE PIN
Installation option 2LOCKING
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
Maximum operating temperature105 °C
Minimum operating temperature-55 °C
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.09 inch
Termination typePRESS FIT
Evacuation force-minimum value.17792 N
PDM: Rev:M
STATUS:
Released
Printed: Dec 20, 2010
.
How to write data to the ICM7212AM LED driver chip?
Hello friends: P0.0-P0.3 of the microcontroller is connected to B0, B1, B2, B3 of icm7212Am; P0.4, p0.5 are connected to DA1, DA2, P2.0 is connected to CS1 (low level is valid), WR is connected to CS2...
magic_jw Embedded System
Hello everyone! Please help!
OMAPL138 DSP, if you run a bare metal program without a DDR chip, can you download it from NandFlash to the DSP chip? Is this solution feasible?...
folung DSP and ARM Processors
Changes in the stylus touch calibration process after changing the screen display orientation
I use a QQ2440V3 board with a 800*480 7-inch screen. I successfully changed the display to portrait mode by adjusting the display driver parameters. I observed that the pen touch calibration procedure...
stlong Embedded System
Which libraries are needed for functions like OpenStore...?
I want to write a small program for disk operation under evc, which needs to use functions such as OpenStore and OpenPartition. The definitions of these functions can be seen in the header file of the...
wbatjd Embedded System
PCB conversion to schematic
I am a beginner in protel and want to convert a PCB diagram into a schematic diagram. Is there any software to do this? There are a lot of copper wires on the PCB diagram, which looks very complicated...
ben007 PCB Design
What you need to know when using electronic plug-in lines on PCB circuit boards
[align=left][b]Plug-in assembly line definition: [/b] [/align] [align=left]Plug-in assembly line uses steel frame and special aluminum alloy track as main parts. The assembly line can be divided into ...
xylianguang Industrial Control Electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 286  1767  2186  105  1324  6  36  45  3  27 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号