EEWORLDEEWORLDEEWORLD

Part Number

Search

51760-10511613BALF

Description
Board Connector, Female, Right Angle, Solder Terminal, Guide Pin, Receptacle
CategoryThe connector    The connector   
File Size259KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

51760-10511613BALF Overview

Board Connector, Female, Right Angle, Solder Terminal, Guide Pin, Receptacle

51760-10511613BALF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerAmphenol
Reach Compliance Codecompliant
Board mount optionsHOLE .086-.098
body width0.47 inch
subject depth0.82 inch
body length8.05 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact completed and terminatedTIN
Contact point genderFEMALE
Contact materialCOPPER ALLOY
Contact resistance20 mΩ
Contact styleHYBRID
Dielectric withstand voltage2500VDC V
Durability200 Cycles
maximum insertion force.973 N
Insulation resistance500000000 Ω
insulator materialGLASS FILLED THERMOPLASTIC
Manufacturer's serial number51760
Mixed contactsYES
Installation option 1GUIDE PIN
Installation option 2LOCKING
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
Maximum operating temperature105 °C
Minimum operating temperature-55 °C
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.09 inch
Termination typeSOLDER
Evacuation force-minimum value.17792 N
PDM: Rev:M
STATUS:
Released
Printed: Dec 20, 2010
.
Recommended PIC chip [radio control function]
[align=left][color=black][font=SimSun][size=9.0pt]I want to ask a small question[/size][/font][/color][color=black][font="][size=9.0pt] [/size][/font][/color][color=black][font=SimSun][size=9.0pt]I ne...
huwiam99 Microchip MCU
EPCS chip programming problem
I want to ask, after programming the EPCS chip through the CONFIG port, if I do not unplug the download line, the FPGA will not start up when I power it on again, nSTATUS will be pulled low, and CONF_...
eeleader-mcu FPGA/CPLD
Questions about multisim simulation
I was recently simulating a 555 oscillator. The square wave I output was input to a voltage follower and then connected to an integrator to get a triangle wave. The problem is as shown in the figure b...
音速兔 Analog electronics
Help, STM32F103 ADC problem
I use two ADCs for data acquisition. No matter in independent mode or synchronous mode, PA0 (channel 0) will have burr-like signals, and PA1 (channel 1) will have a level of about 1.7V (half of the 3....
laowen_110 stm32/stm8
TLC adopts AC voltage
I want to use TLC2543 to collect the instantaneous value of AC. The frequency of AC signal is only 50HZ. I wonder if the speed can be increased in time?...
晴歌 Analogue and Mixed Signal
Design of audio products based on DSP
With the acceleration of the digitalization process, digital signals will replace more analog signal environments. Since 2004, the application of DSP in consumer electronics will enter people's lives ...
fish001 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1754  583  1653  2435  745  36  12  34  50  15 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号