EEWORLDEEWORLDEEWORLD

Part Number

Search

51760-10608018ABLF

Description
Board Connector, Female, Right Angle, Press Fit Terminal, Guide Pin, Receptacle
CategoryThe connector    The connector   
File Size259KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

51760-10608018ABLF Overview

Board Connector, Female, Right Angle, Press Fit Terminal, Guide Pin, Receptacle

51760-10608018ABLF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerAmphenol
Reach Compliance Codecompliant
Board mount optionsHOLE .138-.163
body width0.47 inch
subject depth0.865 inch
body length8.65 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact arrangementS80P24
Contact completed and terminatedTIN
Contact point genderFEMALE
Contact materialCOPPER ALLOY
Contact resistance20 mΩ
Contact styleHYBRID
Dielectric withstand voltage2500VDC V
Durability200 Cycles
maximum insertion force.973 N
Insulation resistance500000000 Ω
insulator materialGLASS FILLED THERMOPLASTIC
Manufacturer's serial number51760
Mixed contactsYES
Installation option 1GUIDE PIN
Installation option 2LOCKING
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
Maximum operating temperature105 °C
Minimum operating temperature-55 °C
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.135 inch
Termination typePRESS FIT
Evacuation force-minimum value.17792 N
PDM: Rev:M
STATUS:
Released
Printed: Dec 20, 2010
.
Regarding the problem of using Hall sensor to measure the start and stop and speed of the motor, there is a point where the problem cannot be solved. Thank you!
A small magnet is placed on the end face of the motor shaft, close to the edge. When the motor starts, the Hall sensor outputs a signal. This signal is used to control the start and stop of the subseq...
xbcai Sensor
MSComm does not display the data sent by the MCU
I use MSP430 to send data to PC, and I can receive the data using the serial port assistant, but I can't display the data using VC++. The following is the control receiving code (the control can commu...
alexanderjue Microcontroller MCU
Do we need to refer to other people's routines?
I am now training driver chips during the summer vacation. I try not to look at other people's manuals. Is it interesting? It takes a long time. I don't know if it is a waste of time. I don't know how...
拿得起铁 MCU
c6655 spi boot problem
I downloaded "Keystone 1 SPI NOR boot steps and precautions" and routines. I used cs1 on my board. After burning the flash, I started in spiboot mode and found that the chip select was always on cs0. ...
lanbo DSP and ARM Processors
Fallen leaves are tired butterflies
The setting sun is getting old, and the west wind is getting stronger. The leaves have fallen, and autumn has come with them. When autumn comes, people become thinner with autumn. With autumn, they be...
babydahua Talking
How do I use the Graphics Resource Converter tool to convert Chinese fonts?
[img=500,303]http://www.microchip.com.tw/uploads/newbb/thumbs/2310_56454377e0b96.jpg[/img] Hello everyone: I use Microchip's Graphics Resource Converter (GRC) tool to convert Windows fonts into ASCII ...
PSIR Microchip MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 872  1803  2552  2323  200  18  37  52  47  5 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号