EEWORLDEEWORLDEEWORLD

Part Number

Search

51760-11305608CBLF

Description
Board Connector, Female, Right Angle, Press Fit Terminal, Guide Pin, Receptacle
CategoryThe connector    The connector   
File Size259KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

51760-11305608CBLF Overview

Board Connector, Female, Right Angle, Press Fit Terminal, Guide Pin, Receptacle

51760-11305608CBLF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerAmphenol
Reach Compliance Codecompliant
Board mount optionsHOLE .138-.163
body width0.47 inch
subject depth0.865 inch
body length7.3 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact completed and terminatedTIN
Contact point genderFEMALE
Contact materialCOPPER ALLOY
Contact resistance20 mΩ
Contact styleHYBRID
Dielectric withstand voltage2500VDC V
Durability200 Cycles
maximum insertion force.973 N
Insulation resistance500000000 Ω
insulator materialGLASS FILLED THERMOPLASTIC
Manufacturer's serial number51760
Mixed contactsYES
Installation option 1GUIDE PIN
Installation option 2LOCKING
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
Maximum operating temperature105 °C
Minimum operating temperature-55 °C
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.154 inch
Termination typePRESS FIT
Evacuation force-minimum value.17792 N
PDM: Rev:M
STATUS:
Released
Printed: Dec 20, 2010
.
Help!!! Emergency Light
I have some faulty emergency lights and want to repair them. I hope there are technicians who can give me some advice. The fault of the emergency lights is that the lights only light up for three seco...
瞎鼓捣 DIY/Open Source Hardware
AM3359 ICE development board running powerlink on Linux
Hi, I have a TI AM3359 ICE development board. I have completed the Linux system porting. I want to run the Powerlink protocol on Linux. However, the network implementation of this board does not suppo...
simonls Linux and Android
V853 Replace the startup LOGO
# The overview mainly describes how to replace the startup LOGO of V853 # Environmental software: V853 Tina 5.0 SDK Hardware: Allwinner V853 development board # Specific steps First, let's take a look...
aleksib Domestic Chip Exchange
Dear big brothers, please help me
module flash_mod(clk,rst,LED_OUT); input clk; inout rst; outputLED_OUT; //----------------------// reg [19:0]cnt; reg led_out; parameter T50ms=20'd999_999; //-------------------------// //------------...
xander_wang FPGA/CPLD
The problem of the servo not rotating when the nodemcu esp8266 development board drives it
[i=s]This post was last edited by xiguabuda on 2022-3-11 22:59[/i]I'm new to this. I'm using a development board and MicroPython to drive the servo, but there's no response. Could you please help me f...
xiguabuda MicroPython Open Source section
Mentor Usage Problems
Dear experts, after installing Mentor DC7.9.2, when Capture Design calls the component library, it cannot be displayed, but the component library can be opened separately. Is there any problem with th...
随风飘啊 PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2085  1046  2405  646  2358  42  22  49  14  48 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号