EEWORLDEEWORLDEEWORLD

Part Number

Search

51760-11806014BBLF

Description
Board Connector, 92 Contact(s), Female, Right Angle, Press Fit Terminal, Guide Pin, Receptacle
CategoryThe connector    The connector   
File Size259KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

51760-11806014BBLF Overview

Board Connector, 92 Contact(s), Female, Right Angle, Press Fit Terminal, Guide Pin, Receptacle

51760-11806014BBLF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerAmphenol
Reach Compliance Codecompliant
Board mount optionsHOLE .138-.163
body width0.47 inch
subject depth0.865 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact arrangementS60P32
Contact completed and terminatedTIN
Contact point genderFEMALE
Contact materialCOPPER ALLOY
Contact resistance20 mΩ
Contact styleHYBRID
Dielectric withstand voltage2500VDC V
Durability200 Cycles
maximum insertion force.973 N
Insulation resistance500000000 Ω
insulator materialGLASS FILLED THERMOPLASTIC
Manufacturer's serial number51760
Mixed contactsYES
Installation option 1GUIDE PIN
Installation option 2LOCKING
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
Maximum operating temperature105 °C
Minimum operating temperature-55 °C
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.09 inch
Termination typePRESS FIT
Total number of contacts92
Evacuation force-minimum value.17792 N
PDM: Rev:M
STATUS:
Released
Printed: Dec 20, 2010
.
Under 6410, I used IROM_Fusing_Tool.exe to make an SD card boot disk and burned something into it, but why did the SD card capacity not change? Is it hidden?
Under 6410, I used IROM_Fusing_Tool.exe to make an SD card boot disk and burned something into it, but why did the SD card capacity not change? Is it hidden?...
htjsmhj Embedded System
DFM should not be limited to chips, PCB needs it more
We all know that even if the silicon is 100% perfect, if any one component of the chip-to-chip communication link (such as the package, connector or circuit board) is damaged, the target system may st...
clj2004000 PCB Design
Report Forum
I've been busy making an amplifier recently, so I don't have time to share my experience with M3 with you. The information is not very valuable (I think the most valuable ones have been posted), and I...
heavenji Microcontroller MCU
Introduction to Intel Embedded Systems Invitational Competition
[i=s]This post was last edited by paulhyde on 2014-9-15 09:01[/i] The "Intel Cup Undergraduate Electronic Design Competition - Embedded System Special Invitational Competition" is part of the National...
open82977352 Electronics Design Contest
Adjustment of basic idle speed of electronically controlled vehicles 3
(2006-04-04 13:20:26 ) e. Turn off the engine after adjusting the basic idle speed, and then clear the fault code (35#) stored in the computer after disconnecting the ISCV circuit. Methods for clearin...
frozenviolet Automotive Electronics
What is the principle of transformer leakage inductance? Why do we need to short-circuit the secondary coil of the transformer when testing leakage inductance?
[size=4] When we use a bridge to test the leakage inductance of a transformer, we need to short-circuit the secondary side, and the inductance obtained by testing the primary side is the leakage induc...
qwqwqw2088 Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 192  2689  943  1802  881  4  55  19  37  18 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号