EEWORLDEEWORLDEEWORLD

Part Number

Search

54111-810-23-1900LF

Description
Board Connector, 23 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size63KB,1 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

54111-810-23-1900LF Overview

Board Connector, 23 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle

54111-810-23-1900LF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerAmphenol
Reach Compliance Codecompliant
body width0.094 inch
subject depth0.748 inch
body length2.3 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact completed and terminatedMatte Tin (Sn) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialTHERMOPLASTIC
JESD-609 codee3
Manufacturer's serial number54111
Plug contact pitch0.1 inch
Installation option 1LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
Plating thickness30u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.095 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts23
PDM: Rev:E
STATUS:
Released
Printed: Jun 03, 2008
.
DSP/BIOS TSK_sleep()
I would like to ask you why the task cannot be woken up again after calling the bios system function TSK_sleep(...) in the task program when programming based on DSP/BIOS. Thank you in advance....
feifei Microcontroller MCU
lm3s101 input signal
In the pdf, I see that 0.4v or less is a low level, and 2v or more is a high level. So will the signal sampled between 0.4v and 2v be considered a high level or a low level? If you don't know 101, you...
sciencekn1 Microcontroller MCU
I2C interface problem of PIC16F877A
I want to use a PIC16F877A as a slave device of the I2C interface. After writing the program and burning it, I found that the clock at the SCL end could not be input. After a period of time, when I in...
old——Jia Microchip MCU
dsp28335 AD sampling single mode
[p=28, null, left][color=rgb(69, 69, 69)]Three modes are configured: single mode, continuous mode and DMA transfer[/color][/p][p=28, null, left][color=rgb(69, 69, 69)]Single mode calls the acquisition...
fish001 DSP and ARM Processors
How to use circuit to stabilize signal?
I want to stabilize the signal output by the low-frequency power amplifier without using a task chip. Can I use some simple components to stabilize the signal? Please give me some advice! Thank you in...
jackiesh Embedded System
XTR111 4-20mA circuit problem
As shown in the figure below, the official 4-20mA schematic diagram is imitated. Since the microcontroller does not have DA, DAC7512 is used. During the debugging process, it is found that the 5V outp...
zixialong Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2152  2513  2802  1209  1520  44  51  57  25  31 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号