EEWORLDEEWORLDEEWORLD

Part Number

Search

54122-810-06-2300LF

Description
Board Connector, 12 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size107KB,1 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

54122-810-06-2300LF Overview

Board Connector, 12 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle

54122-810-06-2300LF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerAmphenol
Reach Compliance Codecompliant
body width0.19 inch
subject depth0.906 inch
body length0.6 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact completed and terminatedMatte Tin (Sn) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialTHERMOPLASTIC
JESD-609 codee3
Manufacturer's serial number54122
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation option 1LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thickness15u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.12 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts12
PDM: Rev:K
STATUS:
Released
Printed: Mar 10, 2011
.
[GD32L233C-START Review] 18. Hardware SPI driver (ST7735) 1.8-inch TFT LCD
Related articles: [GD32L233C-START Review] 1. GD32L233C-START with obvious advantages and disadvantages (unboxing) [GD32L233C-START Review] 2. Non-blocking way to light up, blink, blink, blink... [GD3...
freeelectron GD32 MCU
LM358 single op amp connected as instrument amplifier
A single op amp is connected as an instrumentation amplifier. According to the manual, the front stage is the input of two differential signals, each amplified 100 times, and then sent to the back sta...
dingshidong Analog electronics
Modem dial-up link establishment problem
I used the AT command ATDT (calling end) and ATA (called end), and the number was dialed, but why is there no carrier? The modems cannot transmit data, what's going on?...
sdsongth Embedded System
PCB Layout Design Specifications - Device Selection
[i=s]This post was last edited by ohahaha on 2018-4-23 11:52[/i] [align=left][size=4]PCB Layout Design Specifications - Device Selection[/size][/align][align=left][size=4] [/size][/align][align=left][...
ohahaha PCB Design
IIC of the self-made STM8 development board cannot be used
This is the schematic diagram of the board I drew, using STM8S003F3, using IIC to read and write 24C32, with a pull-up resistor of 3.3K. I used another STM8S003F3 development board with the same progr...
石玉 MCU
Smart electronic level
I just submitted a smart bike companion, and later found out that someone else has made one. In order to make a SensorTag for fun, I submitted another solution. Since the difficult ones have been done...
littleshrimp Wireless Connectivity

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 992  684  28  1150  852  20  14  1  24  18 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号