The AS7C1024B is a high performance CMOS 1,048,576-bit Static Random Access Memory (SRAM) device organized as 131,072 words x 8
bits. It is designed for memory applications where fast data access, low power, and simple interfacing are desired.
Equal address access and cycle times (t
AA
, t
RC
, t
WC
) of 10/12/15/20 ns with output enable access times (t
OE
) of 5/6/7/8 ns are ideal for high
performance applications. Active high and low chip enables (CE1, CE2) permit easy memory expansion with multiple-bank systems.
When CE1 is high or CE2 is low, the devices enter standby mode. If inputs are still toggling, the device will consume I
SB
power. If the bus is
static, then full standby power is reached (I
SB1
). For example, the AS7C1024B is guaranteed not to exceed 55 mW under nominal full standby
conditions.
A write cycle is accomplished by asserting write enable (WE) and both chip enables (CE1, CE2). Data on the input pins I/O0 through I/O7 is
written on the rising edge of WE (write cycle 1) or the active-to-inactive edge of CE1 or CE2 (write cycle 2). To avoid bus contention, external
devices should drive I/O pins only after outputs have been disabled with output enable (OE) or write enable (WE).
A read cycle is accomplished by asserting output enable (OE) and both chip enables (CE1, CE2), with write enable (WE) high. The chips drive I/
O pins with the data word referenced by the input address. When either chip enable is inactive, output enable is inactive, or write enable is active,
output drivers stay in high-impedance mode.
Absolute maximum ratings
Parameter
Voltage on V
CC
relative to GND
Voltage on any pin relative to GND
Power dissipation
Storage temperature (plastic)
Ambient temperature with V
CC
applied
DC current into outputs (low)
Symbol
V
t1
V
t2
P
D
T
stg
T
bias
I
OUT
Min
–0.50
–0.50
–
–65
–55
–
Max
+7.0
V
CC
+0.50
1.0
+150
+125
20
Unit
V
V
W
°C
°C
mA
Note: Stresses greater than those listed under
Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions outside those indicated in the operational sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect reliability.
Truth table
CE1
H
X
L
L
L
CE2
X
L
H
H
H
WE
X
X
H
H
L
OE
X
X
H
L
X
Data
High Z
High Z
High Z
D
OUT
D
IN
Mode
Standby (I
SB
, I
SB1
)
Standby (I
SB
, I
SB1
)
Output disable (I
CC
)
Read (I
CC
)
Write (
ICC
)
Key: X = don’t care, L = low, H = high
3/26/04, v 1.2
Alliance Semiconductor
P. 2 of 9
AS7C1024B
®
Recommended operating conditions
Parameter
Supply Voltage
Input Voltage
Ambient operating
temperature
commercial
industrial
Symbol
V
CC
V
IH
V
IL
T
A
T
A
Min
4.5
2.2
–0.5
0
–40
Nominal
5.0
-
–
–
–
Max
5.5
V
CC
+ 0.5
0.8
70
85
Unit
V
V
V
°C
°C
V
IL
min = -1.0V for pulse width less than 5ns
V
IH
max = V
CC
+2.0V for pulse width less than 5ns.
DC operating characteristics (over the operating range)
As the title says, [color=#FF0000]Hope the moderator recommends[/color] For a long time, because the ARM development board has to regenerate NK every time the screen is changed, has anyone ever driven...
[color=rgb(51, 51, 51)] [font=宋体]The traditional Western holiday Christmas is coming soon. With the continuous exchange and integration of Chinese and Western cultures in recent years, Christmas has l...
Why does the following wait statement not work and the output does not change?module my_wait(input clk, output ok); reg x=1'b0; always wait (clk) begin x=~x; end assign ok=x; endmodule eeworldpostqq...
The LED keyboard indicator lights of 7 rows and 5 columns, when the key is pressed, the corresponding LED indicator lights will also light up! The principle of lighting up: the column is high level, t...
The USB learning board has been completed and a batch has been made recently. If you need it, you can participate in this group purchase activity.Team leader registration number: EEWORLD_005
The group...
A single-chip microcomputer is also called a single-chip microcontroller. It is not a chip that completes a certain logical function, but a computer system integrated into one chip. In general, a c...[Details]
System design is a complex process. It is not enough to just use ICs. There are many details to consider. This article uses a high-fidelity music playback system as an example to introduce how to s...[Details]
As cellular phones become more advanced, the power consumption of the system during operation and the power consumption during standby are also increasing. Therefore, the power management design of...[Details]
A multi-point temperature control heating control system was designed using the SST89E564RC single-chip microcomputer and a new temperature measuring device. The heating system can be controlled in...[Details]
my country is a big country in agriculture, grain production and consumption. Grains are a necessary condition for our nation to survive and develop. The flour processing industry will exist forever w...[Details]
With the advocacy and implementation of the government's Safe City Plan, the security market has increasingly higher requirements for the clarity of surveillance images. Imagine that after a case o...[Details]
This paper designs a 16x16LED Chinese character display bar based on single-chip dynamic scanning control, briefly analyzes the principle of Chinese character display, and studies how the LED displ...[Details]
introduction
At present, measuring instruments are developing towards networking, and each individual embedded instrument will become a node on the Internet. This system realizes the network...[Details]
Traditional
virtual instruments
consist of a data acquisition
board
based on PCI bus and
corresponding software. However, with
the rapid development of
computer
network techno...[Details]
In the "digital pressure measurement" experimental device of applied physics, the subject technical knowledge of analog circuits, digital circuits, sensors and single-chip microcomputers is used. In o...[Details]
This article discusses the six design steps of LED lighting system design in detail: (1) determine the lighting requirements; (2) determine the design goals and estimate the optics; (3) the efficie...[Details]
People who often surf the Internet until late at night, their families always complain that turning on the big lights in the living room affects their rest, but some people don't have keyboard ligh...[Details]
With the popularity of digital appliances, rechargeable batteries can be seen everywhere in people's daily lives and have become one of the indispensable daily necessities.
This article gives ...[Details]
The overall operating performance of an electric car depends first on its battery system and motor drive system. The drive system of an electric car is generally composed of three main parts: a con...[Details]
introduction
Belt drive is a common transmission device used in industrial production. Its commonly used speed detection device is a photoelectric encoder installed at the rotating end of th...[Details]
ARM Technology
京公网安备 11010802033920号
EEWORLD
