The AS7C1024 and AS7C31024 are high performance CMOS 1,048,576-bit Static Random Access Memory (SRAM) devices
organized as 131,072 words × 8 bits. It is designed for memory applications where fast data access, low power, and simple
interfacing are desired.
Equal address access and cycle times (t
AA
, t
RC
, t
WC
) of 10/12/15/20 ns with output enable access times (t
OE
) of 5/6/8/10 ns
are ideal for high performance applications. Active high and low chip enables (CE1, CE2) permit easy memory expansion with
multiple-bank systems.
When CE1 is high or CE2 is low the devices enter standby mode. If inputs are still toggling, the device will consume I
SB
power.
If the bus is static, then full standby power is reached (I
SB1
or I
SB2
). For example, the AS7C31024 is guaranteed not to exceed
0.33mW under nominal full standby conditions. All devices in this family will retain data when VCC is reduced as low as 2.0V.
A write cycle is accomplished by asserting write enable (WE) and both chip enables (CE1, CE2). Data on the input pins I/O0-
I/O7 is written on the rising edge of WE (write cycle 1) or the active-to-inactive edge of CE1 or CE2 (write cycle 2). To avoid
bus contention, external devices should drive I/O pins only after outputs have been disabled with output enable ( OE) or write
enable (WE).
A read cycle is accomplished by asserting output enable (OE) and both chip enables (CE1, CE2), with write enable (WE) high.
The chips drive I/O pins with the data word referenced by the input address. When either chip enable is inactive, output
enable is inactive, or write enable is active, output drivers stay in high-impedance mode.
Absolute maximum ratings
Parameter
Voltage on V
CC
relative to GND
Voltage on any pin relative to GND
Power dissipation
Storage temperature (plastic)
Ambient temperature with V
CC
applied
DC current into outputs (low)
AS7C1024
AS7C31024
Symbol
V
t1
V
t1
V
t2
P
D
T
stg
T
bias
I
OUT
Min
–0.50
-0.50
–0.50
–
–65
–55
–
Max
+7.0
+5.0
V
CC
+0.50
1.0
+150
+125
20
Unit
V
V
V
W
°
C
°
C
mA
Note: Stresses greater than those listed under
Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions outside those indicated in the operational sections of this specificati on is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect reliability.
Truth table
CE1
H
X
L
L
L
CE2
X
L
H
H
H
WE
X
X
H
H
L
OE
X
X
H
L
X
Data
High Z
High Z
High Z
D
OUT
D
IN
Mode
Standby (I
SB
, I
SB1
)
Standby (I
SB
, I
SB1
)
Output disable (I
CC
)
Read (I
CC
)
Write (
ICC
)
Key: X = Don’t Care, L = Low, H = High
2
ALLIANCE SEMICONDUCTOR
11/29/00
®
AS7C1024
AS7C31024
Recommended operating conditions
Parameter
Supply voltage
Device
AS7C1024
AS7C31024
AS7C1024
Input voltage
AS7C31024
commercial
industrial
Symbol
V
CC
V
CC
V
IH
V
IH
V
IL†
Ambient operating temperature
†
V min = –3.0V for pulse width less than t
IL
RC/2
.
Min
4.5
3.0
2.2
2.0
–0.5
0
–40
Nominal
5.0
3.3
–
–
–
–
–
Max
5.5
3.6
V
CC
+ 0.5
V
CC
+ 0.5
0.8
70
85
Unit
V
V
V
V
V
°
C
°
C
T
A
T
A
DC operating characteristics (over the operating range)
Haha, this C8051F microcontroller simulation and programming must use a dedicated device. The official simulation programmer is called USB Debug Adapter. There is a user manual, which contains the cir...
I want to learn TI's M3 and look at a development board, but I don't see many resources. Does anyone have any recommendations? It's best to have more resources. I'm a beginner and I want more informat...
1. Low power consumption + interruptionMain function{Disable watchdogSetting the system clockInitialize peripheral devices such as displayInitialization settings of internal resources such as timersEn...
[i=s]This post was last edited by wytalfred on 2014-3-24 22:57[/i] First, prepare the LCD screen and game controller, etc. Then install the simulator. I installed two, download them here: OSMOSE (supp...
Embedded System
京公网安备 11010802033920号
EEWORLD
