The AS7C31025B is a high-performance CMOS 1,048,576-bit Static Random Access Memory (SRAM) device organized as 131,072 x 8
bits. It is designed for memory applications where fast data access, low power, and simple interfacing are desired.
Equal address access and cycle times (t
AA
, t
RC
, t
WC
) of 10/12/15/20 ns with output enable access times (t
OE
) of 5, 6, 7, 8 ns are ideal for
high-performance applications. The chip enable input CE permits easy memory and expansion with multiple-bank memory systems.
When CE is high the device enters standby mode. A write cycle is accomplished by asserting write enable (WE) and chip enable (CE). Data
on the input pins I/O0 through I/O7 is written on the rising edge of WE (write cycle 1) or CE (write cycle 2). To avoid bus contention,
external devices should drive I/O pins only after outputs have been disabled with
output enable (
OE
) or write enable
(WE).
A read cycle is accomplished by asserting output enable (OE) and chip enable (CE), with write enable (WE) high. The chip drives I/O pins
with the data word referenced by the input address. When either chip enable or output enable is inactive or write enable is active, output
drivers stay in high-impedance mode.
All chip inputs and outputs are TTL-compatible, and operation is from a single 3.3 V supply. The AS7C31025B is packaged in common
industry standard packages.
Absolute maximum ratings
Parameter
Voltage on V
CC
relative to GND
Voltage on any pin relative to GND
Power dissipation
Storage temperature (plastic)
Ambient temperature with V
CC
applied
DC current into outputs (low)
Symbol
V
t1
V
t2
P
D
T
stg
T
bias
I
OUT
Min
–0.50
–0.50
–
–65
–55
–
Max
+5.0
V
CC
+ 0.5
1.0
+150
+125
20
Unit
V
V
W
o
C
o
C
mA
NOTE: Stresses greater than those listed under
Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress rating only and func-
tional operation of the device at these or any other conditions outside those indicated in the operational sections of this specification is not implied. Exposure
to absolute maximum rating conditions for extended periods may affect reliability.
Truth table
CE
H
L
L
L
WE
X
H
H
L
OE
X
H
L
X
Data
High Z
High Z
D
OUT
D
IN
Mode
Standby (I
SB
, I
SB1
)
Output disable (I
CC
)
Read (I
CC
)
Write (I
CC
)
Key: X = don’t care, L = low, H = high.
3/24/04, v. 1.3
Alliance Semiconductor
P. 2 of 9
AS7C31025B
®
Recommended operating conditions
Parameter
Supply voltage
Input voltage
Ambient operating temperature
V
IL
= -1.0V for pulse width less than 5ns
V
IH =
V
CC
+ 1.5V for pulse width less than 5ns
Symbol
V
CC
V
IH
V
IL
T
A
T
A
Min
3.0
2.0
–0.5
0
–40
Nominal
3.3
–
–
–
–
Max
3.6
V
CC
+ 0.5
0.8
70
85
Unit
V
V
V
o
C
o
C
DC operating characteristics (over the operating range)
[size=4]Experimental phenomenon: [/size] [size=4] [/size] [size=4]One EB2530 (terminal A) is defined as a transmitting module, and the other EB2530 (terminal B) is defined as a receiving module. [/siz...
I recently stored data in an SD card. Since I didn't use a file system, I couldn't see the stored data, so I wrote a read function. When I displayed it through the serial port debugging assistant, som...
[font=微软雅黑][size=3][color=#000] How is everyone's progress in the activity of learning to draw a four-layer board a while ago? Some people have already finished drawing and even wrote a summary! [/col...
TCH05A: Also belongs to the TCH08 series, it is a cost-effective touch sensing detection IC that can provide up to 5 sensing keys. The touch sensing detection key can penetrate the insulating material...
Do you often have to add brake fluid to your car's brakes? The fact that you need to pump out the brake fluid to make sure there is no gas in the brake fluid line may not be done by the car owner h...[Details]
Analog engineers have traditionally struggled with complexity when designing power supplies that required multiple outputs, dynamic load sharing, hot-swap, or extensive fault-handling capabilities....[Details]
There are three types of mobile TV: one is based on analog TV broadcasting network, another is based on mobile communication network, and the other is based on digital broadcasting network. The f...[Details]
As LEDs continue to improve in almost every aspect of performance and cost, LED lighting is being used in an increasingly wide range of applications, among which LED street lights are a focus of in...[Details]
The reason for the light decay of white LEDs: the decline of phosphor performance
So far, the rapid decline of the luminous performance of white light LEDs, especially low-power white light LE...[Details]
For a long time, due to the limitation of hardware conditions, the display devices of traditional small handheld devices such as PDA are usually monochrome LCD, and the user interface is very simpl...[Details]
With the rapid development of urban economy, elevators are increasingly used as a vertical transportation tool. However, elevator fault detection and maintenance, especially the role of elevator remot...[Details]
1. Principle of displacement angle sensor
The angle sensor is used to detect angles. It has a hole in its body that fits the LEGO axle. When connected to the RCX, the angle sensor counts once ...[Details]
From the PIC16F946 datasheet, we know that there are two ways to write values to the LCD for display:
1. Directly write the value to LCDDATA1~LCDDATA23
2. Use disconnect t...[Details]
A standard cell
is an electrochemical
cell
used as a voltage reference standard in many electrical standards laboratories
. If properly maintained, standard cells are very stable. The ...[Details]
LED is the abbreviation of light emitting diode, which is an electric light source made of semiconductor technology. The core part of LED is a chip composed of P-type semiconductor and N-type semi...[Details]
Toyohashi University of Technology demonstrated electric field coupled wireless power supply technology using life-size car tires and roads at the wireless technology exhibition "Wireless Technolog...[Details]
12v Lead Acid batteries used in trucks, cars, RVs and uninterruptible power supplies are usually rated at 12V. This circuit monitors the battery, the charge and discharge curves, gives the cu...[Details]
The concept of state machine
State machine is an important concept in software programming. More important than this concept is its flexible application. In a clear and efficient program, ther...[Details]
Continuity test
A variety of devices need to be checked for continuity, including cable assemblies, printed circuit boards, and connectors to ensure that these components have the expected contin...[Details]
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
