The AS7C3256A is a 3.3V high-performance CMOS 262,144-bit Static Random-Access Memory (SRAM) device
organized as 32,768 words × 8 bits. It is designed for memory applications requiring fast data access at low voltage,
including Pentium
TM
, PowerPC
TM
, and portable computing. Alliance’s advanced circuit design and process techniques
permit 3.3V operation without sacrificing performance or operating margins.
The device enters
standby mode
when
CE
is high. CMOS standby mode consumes 7.2 mW. Normal operation offers 75%
power reduction after initial access, resulting in significant power savings during CPU idle, suspend, and stretch mode.
Equal address access and cycle times (t
AA
, t
RC
, t
WC
) of 10/12/15/20 ns with output enable access times (t
OE
) of 5, 6, 7, 8 ns
are ideal for high-performance applications. The chip enable (
CE
) input permits easy memory expansion with multiple-bank
memory organizations.
A write cycle is accomplished by asserting chip enable (CE) and write enable (WE) LOW. Data on the input pins I/O0-I/O7
is written on the rising edge of WE (write cycle 1) or CE (write cycle 2). To avoid bus contention, external devices should
drive I/O pins only after outputs have been disabled with output enable (OE) or write enable (WE).
A read cycle is accomplished by asserting chip enable (
CE
) and output enable (
OE
) LOW, with write enable (
WE
) high. The
chip drives I/O pins with the data word referenced by the input address. When chip enable or output enable is high, or write
enable is low, output drivers stay in high-impedance mode.
All chip inputs and outputs are TTL-compatible. Operation is from a single 3.3 ±0.3V supply. The AS7C3256A is packaged
in high volume industry standard packages.
Absolute maximum ratings
Parameter
Voltage on V
CC
relative to GND
Voltage on any pin relative to GND
Power dissipation
Storage temperature (plastic)
Ambient temperature with V
CC
applied
DC current into outputs (low)
Symbol
V
t1
V
t2
P
D
T
stg
T
bias
I
OUT
Min
–0.5
–0.5
–
–65
–55
–
Max
+5.0
V
CC
+ 0.5
1.0
+150
+125
20
Unit
V
V
W
o
C
o
C
mA
Stresses greater than those listed under
Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions outside those indicated in the operational sections of this specification is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect reliability.
Truth table
CE
H
L
L
L
WE
X
H
H
L
OE
X
H
L
X
High Z
High Z
D
OUT
D
IN
Data
Mode
Standby (I
SB
, I
SB1
)
Output disable (I
CC
)
Read (I
CC
)
Write (I
CC
)
Key:
X = Don’t care, L = Low, H = High
4/23/04; v.2.0
Alliance Semiconductor
P. 2 of 9
AS7C3256A
®
Recommended operating conditions
Parameter
Supply voltage
Input voltage
Ambient operating temperature
commercial
industrial
Symbol
V
CC
V
IH**
V
IL*
T
A
T
A
Min
3.0
2.0
-0.5
0
–40
Typical
3.3
–
–
–
–
Max
3.6
V
CC
+0.5
0.8
70
85
Unit
V
V
V
o
C
o
C
* V min = –1.0V for pulse width less than 5ns.
**
IL
V
IH
max = V
CC
+ 2.0V for pulse width less than 5ns.
DC operating characteristics (over the operating range)
I searched for devices on our website today, but the following error occurred and I could not search anymore.
“
Service Unavailable
”I don't know if this is the right reaction, please solve it, haha...
Recruiting part-time HyperLynx and other related lecturers, short period, weekends. If you want to earn some extra money, accumulate resources, and enrich your life, please contact me. You are require...
Dear experts, I would like to ask about the synchronous debugging of multiple C6678 chips: I plan to make two boards, each board integrates two C6678 chips, and the communication between the boards is...
Basic knowledge for hardware engineers Purpose: To understand and master the most basic knowledge to become a qualified hardware engineer based on practical experience and actual projects. 1) Basic de...
I just started learning this software. I saw that the information of each resistor and capacitor in the schematic diagram in the textbook was marked with a numerical value followed by the unit Ω or F....
Assume that data is read from 8-bit AD (if it is a higher-bit AD, the data type can be defined as int), the subroutine is get_ad();
1. Limited secondary filtering
/* A value can be adjust...[Details]
Floating-point digital signal processing has become a constant requirement for precision technology, often in applications requiring high accuracy in areas such as aviation, industrial machinery, a...[Details]
In this article, the high-performance DSP developed by TI can be used as an effective confidentiality method if it is applied to PC encryption cards.
As an effective network security solution,...[Details]
In public places such as schools, government agencies, factories and mines, as well as public corridors in residential areas, the phenomenon of long-burning lights is very common, which causes a h...[Details]
1 Introduction
Solar street lights are mainly composed of four parts: solar photovoltaic cell components, batteries, charge and discharge controllers, and lighting fixtures. The bo...[Details]
Introduction
Power subsystems are becoming more and more integrated into the overall system. Power systems have moved from being separate "essential dangerous devices" to being monitorable...[Details]
1. Principle of displacement angle sensor
The angle sensor is used to detect angles. It has a hole in its body that fits the LEGO axle. When connected to the RCX, the angle sensor counts once ...[Details]
Contact resistance
is the resistance to current flow through a closed pair of contacts. This type of measurement is performed on devices such as connectors,
relays
, and switches. The...[Details]
1. System Structure
This system is a simulation system of indoor air-conditioning temperature/humidity control system. The data acquisition and control center collects temperature/humidity...[Details]
1 Introduction to HART Protocol
HART (Highway Addressable Remote Transducer), an open communication protocol for addressable remote sensor high-speed channels, was launched by Rosemen in the U...[Details]
Overview
In spectral measurement, photomultiplier tubes (PMT) and charge-coupled devices (CCD) are often used as photoelectric converters. PMT is used in slow-changing, high-precision spectral...[Details]
1. Disadvantages of choosing too high a voltage level
Choosing too high a voltage level will result in too high an investment and a long payback period. As the voltage level increases, the...[Details]
Corelink Semiconductor has launched the CL1100-based 5-7W E27 LED lighting driver system solution DB2. This driver module meets the requirements of small size (L×W×H=5.1cm×2.1cm×1.8cm), low standby...[Details]
Since the late 1990s, with the demand for higher system efficiency and lower power consumption, the technological update of telecommunications and data communication equipment has promoted the deve...[Details]
Suggestions & Announcements
京公网安备 11010802033920号
EEWORLD
