February 2005
®
AS7C33128FT32B
AS7C33128FT36B
3.3V 128K
×
32/36 Flow Through Synchronous SRAM
Features
•
•
•
•
•
•
•
Organization: 131,072 words × 32 or 36 bits
Fast clock to data access: 6.5/7.5/8.0/10.0 ns
Fast OE access time: 3.5/4.0 ns
Fully synchronous flow through operation
Asynchronous output enable control
Available in 100-pin TQFP package
Individual byte write and Global write
•
•
•
•
•
•
Multiple chip enables for easy expansion
3.3V core power supply
2.5V or 3.3V I/O operation with separate V
DDQ
Linear or interleaved burst control
Snooze mode for reduced power standby
Common data inputs and data outputs
Logic block diagram
LBO
CLK
ADV
ADSC
ADSP
A[18:0]
19
Q0
Burst logic
Q1
19
D
Q
CE
Address
register
CLK
D
DQ
d
Q
Byte write
registers
CLK
D
DQ
Q
c
Byte write
registers
CLK
D
DQ
b
Q
Byte write
registers
CLK
DQ
a
Q
Byte write
registers
CLK
D
Enable
CE
register
CLK
Power
down
D
Enable
Q
delay
register
CLK
36/32
DQ[a:d]
Q
D
BW
a
CE0
CE1
CE2
4
CLK
CE
CLR
17
19
128K × 32/36
Memory
array
GWE
BWE
BW
d
36/32
36/32
BW
c
BW
b
OE
Output
buffer
Input
registers
CLK
ZZ
OE
Selection guide
–65
Minimum cycle time
Maximum clock access time
Maximum operating current
Maximum standby current
Maximum CMOS standby current (DC)
7.5
6.5
275
90
30
-75
8.5
7.5
250
85
30
-80
10
8.0
215
75
30
-10
12
10.0
185
75
30
Units
ns
ns
mA
mA
mA
2/8/05; v.1.2
Alliance Semiconductor
P. 1 of 19
Copyright © Alliance Semiconductor. All rights reserved.
AS7C33128FT32B
AS7C33128FT36B
®
4 Mb Synchronous SRAM products list
1,2
Org
256KX18
128KX32
128KX36
256KX18
128KX32
128KX36
256KX18
128KX32
128KX36
256KX18
128KX32
128KX36
256KX18
128KX32
128KX36
Part Number
AS7C33256PFS18B
AS7C33128PFS32B
AS7C33128PFS36B
AS7C33256PFD18B
AS7C33128PFD32B
AS7C33128PFD36B
AS7C33256FT18B
AS7C33128FT32B
AS7C33128FT36B
AS7C33256NTD18B
AS7C33128NTD32B
AS7C33128NTD36B
AS7C33256NTF18B
AS7C33128NTF32B
AS7C33128NTF36B
Mode
PL-SCD
PL-SCD
PL-SCD
PL-DCD
PL-DCD
PL-DCD
FT
FT
FT
NTD-PL
NTD-PL
NTD-PL
NTD-FT
NTD-FT
NTD-FT
Speed
200/166/133 MHz
200/166/133 MHz
200/166/133 MHz
200/166/133 MHz
200/166/133 MHz
200/166/133 MHz
6.5/7.5/8.0/10 ns
6.5/7.5/8.0/10 ns
6.5/7.5/8.0/10 ns
200/166/133 MHz
200/166/133 MHz
200/166/133 MHz
6.5/7.5/8.0/10 ns
6.5/7.5/8.0/10 ns
6.5/7.5/8.0/10 ns
1 Core Power Supply: VDD = 3.3V + 0.165V
2 I/O Supply Voltage: VDDQ = 3.3V + 0.165V for 3.3V I/O
VDDQ = 2.5V + 0.125V for 2.5V I/O
PL-SCD
PL-DCD
FT
NTD
1
-PL
NTD-FT
:
:
:
:
:
Pipelined Burst Synchronous SRAM - Single Cycle Deselect
Pipelined Burst Synchronous SRAM - Double Cycle Deselect
Flow-through Burst Synchronous SRAM
Pipelined Burst Synchronous SRAM with NTD
TM
Flow-through Burst Synchronous SRAM with NTD
TM
1. NTD: No Turnaround Delay. NTD
TM
is a trademark of Alliance Semiconductor Corporation. All trademarks mentioned in this document are the property
of their respective owners.
2/8/05; v.1.2
Alliance Semiconductor
P. 2 of 19
AS7C33128FT32B
AS7C33128FT36B
®
Pin arrangement
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
A
A
CE0
CE1
BW
d
BW
c
BW
b
BW
a
CE2
V
DD
V
SS
CLK
GWE
BWE
OE
ADSC
ADSP
ADV
A
A
DQP
c
/NC
DQ
c0
DQ
c1
V
DDQ
V
SSQ
DQ
c2
DQ
c3
DQ
c4
DQ
c5
V
SSQ
V
DDQ
DQ
c6
DQ
c7
NC
V
DD
NC
V
SS
DQ
d0
DQ
d1
V
DDQ
V
SSQ
DQ
d2
DQ
d3
DQ
d4
DQ
d5
V
SSQ
V
DDQ
DQ
d6
DQ
d7
DQP
d
/NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
TQFP 14 × 20 mm
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
DQP
b
/NC
DQ
b7
DQ
b6
V
DDQ
V
SSQ
DQ
b5
DQ
b4
DQ
b3
DQ
b2
V
SSQ
V
DDQ
DQ
b1
DQ
b0
V
SS
NC
VDD
ZZ
DQ
a7
DQ
a6
V
DDQ
V
SSQ
DQ
a5
DQ
a4
DQ
a3
DQ
a2
V
SSQ
V
DDQ
DQ
a1
DQ
a0
DQP
a
/NC
2/8/05; v.1.2
LBO
A
A
A
A
A1
A0
NC
NC
V
SS
V
DD
NC
NC
A
A
A
A
A
A
A
Note: Pins 1,30,51,80 are NC for ×32
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Alliance Semiconductor
P. 3 of 19
AS7C33128FT32B
AS7C33128FT36B
®
Functional description
The AS7C33128FT32B/36B is a high-performance CMOS 4-Mbit synchronous Static Random Access Memory (SRAM) device organized
as 131,072 words × 32 or 36 bits.
Fast cycle times of 7.5/8.5/10/12 ns with clock access times (t
CD
) of 6.5/7.5/8.0/10 ns. Three chip enable (CE) inputs permit easy memory
expansion. Burst operation is initiated in one of two ways: the controller address strobe (ADSC), or the processor address strobe (ADSP).
The burst advance pin (ADV) allows subsequent internally generated burst addresses.
Read cycles are initiated with ADSP (regardless of WE and ADSC) using the new external address clocked into the on-chip address register
when ADSP is sampled low, the chip enables are sampled active, and the output buffer is enabled with OE. In a read operation, the data
accessed by the current address registered in the address registers by the positive edge of CLK are carried to the data-out buffer. ADV is
ignored on the clock edge that samples ADSP asserted, but is sampled on all subsequent clock edges. Address is incremented internally for
the next access of the burst when ADV is sampled low and both address strobes are high. Burst mode is selectable with the LBO input. With
LBO unconnected or driven high, burst operations use an interleaved count sequence. With LBO driven low, the device uses a linear count
sequence.
Write cycles are performed by disabling the output buffers with OE and asserting a write command. A global write enable GWE writes all
32/36 regardless of the state of individual BW[a:d] inputs. Alternately, when GWE is high, one or more bytes may be written by asserting
BWE and the appropriate individual byte BWn signals.
BWn is ignored on the clock edge that samples ADSP low, but it is sampled on all subsequent clock edges. Output buffers are disabled when
BWn is sampled LOW regardless of OE. Data is clocked into the data input register when BWn is sampled low. Address is incremented
internally to the next burst address if BWn and ADV are sampled low.
Read or write cycles may also be initiated with ADSC instead of ADSP. The differences between cycles initiated with ADSC and ADSP are
as follows:
• ADSP must be sampled high when ADSC is sampled low to initiate a cycle with ADSC.
• WE signals are sampled on the clock edge that samples ADSC low (and ADSP high).
• Master chip enable CE0 blocks ADSP, but not ADSC.
The AS7C33128FT32B and AS7C33128FT36B family operates from a core 3.3V power supply. I/Os use a separate power supply that can
operate at 2.5V or 3.3V. These devices are available in a 100-pin TQFP package.
TQFP capacitance
Parameter
Input capacitance
I/O capacitance
*Guaranteed not tested
Symbol
C
IN*
C
I/O*
Test conditions
V
IN
= 0V
V
OUT
= 0V
Min
-
-
Max
5
7
Unit
pF
pF
TQFP thermal resistance
Description
Thermal resistance
(junction to ambient)
1
Thermal resistance
(junction to top of case)
1
1 This parameter is sampled
Conditions
1–layer
Test conditions follow standard test methods and
procedures for measuring thermal impedance,
per EIA/JESD51
4–layer
Symbol
θ
JA
θ
JA
θ
JC
Typical
40
22
8
Units
°C/W
°C/W
°C/W
2/8/05; v.1.2
Alliance Semiconductor
P. 4 of 19
AS7C33128FT32B
AS7C33128FT36B
®
Signal descriptions
Pin
CLK
A,A0,A1
DQ[a,b,c,d]
CE0
CE1, CE2
ADSP
ADSC
ADV
GWE
BWE
BW[a,b,c,d]
OE
LBO
ZZ
NC
I/O
I
I
I/O
I
I
I
I
I
I
I
I
I
I
I
-
Properties
CLOCK
SYNC
SYNC
SYNC
SYNC
SYNC
SYNC
SYNC
SYNC
SYNC
SYNC
ASYNC
STATIC
ASYNC
-
Description
Clock. All inputs except OE, ZZ, and LBO are synchronous to this clock.
Address. Sampled when all chip enables are active and when ADSC or ADSP are asserted.
Data. Driven as output when the chip is enabled and when OE is active.
Master chip enable. Sampled on clock edges when ADSP or ADSC is active. When CE0 is inactive,
ADSP is blocked. Refer to the “Synchronous truth table” for more information.
Synchronous chip enables, active high, and active low, respectively. Sampled on clock edges when
ADSC is active or when CE0 and ADSP are active.
Address strobe processor. Asserted low to load a new address or to enter standby mode.
Address strobe controller. Asserted low to load a new address or to enter standby mode.
Advance. Asserted low to continue burst read/write.
Global write enable. Asserted low to write all 32/36 bits. When high, BWE and BW[a:d] control write
enable.
Byte write enable. Asserted low with GWE high to enable effect of BW[a:d] inputs.
Write enables. Used to control write of individual bytes when GWE is high and BWE is low. If any of
BW[a:d] is active with GWE high and BWE low, the cycle is a write cycle. If all BW[a:d] are inactive,
the cycle is a read cycle.
Asynchronous output enable. I/O pins are driven when OE is active and chip is in read mode.
Selects Burst mode. When tied to V
DD
or left floating, device follows interleaved Burst order. When
driven Low, device follows linear Burst order.
This signal is internally pulled High.
Snooze. Places device in low power mode; data is retained. Connect to GND if unused.
No connect
Snooze Mode
SNOOZE MODE is a low current, power-down mode in which the device is deselected and current is reduced to I
SB2
. The duration of
SNOOZE MODE is dictated by the length of time the ZZ is in a High state.
The ZZ pin is an asynchronous, active high input that causes the device to enter SNOOZE MODE.
When the ZZ pin becomes a logic High, I
SB2
is guaranteed after the time t
ZZI
is met. After entering SNOOZE MODE, all inputs except ZZ
is disabled and all outputs go to High-Z. Any operation pending when entering SNOOZE MODE is not guaranteed to successfully complete.
Therefore, SNOOZE MODE (READ or WRITE) must not be initiated until valid pending operations are completed. Similarly, when exiting
SNOOZE MODE during t
PUS
, only a DESELECT or READ cycle should be given while the SRAM is transitioning out of SNOOZE MODE.
2/8/05; v.1.2
Alliance Semiconductor
P. 5 of 19
京公网安备 11010802033920号
EEWORLD
