The AS7C33128PFS32A and AS7C33128PFS36A are high-performance CMOS 4-Mbit synchronous Static Random Access Memory (SRAM)
devices organized as 131,072 words × 32 or 36 bits, and incorporate a two-stage register-register pipeline for highest frequency on any given
technology.
Timing for these devices is compatible with existing Pentium
®
synchronous cache specifications. This architecture is suited for ASIC, DSP
(TMS320C6X), and PowerPC
™
1
-based systems in computing, datacom, instrumentation, and telecommunications systems.
Fast cycle times of 5.0/5.4/6.0/7.5/10 ns with clock access times (t
CD
) of 3.0/3.1/3.5/4.0/5.0 ns enable 200, 183, 166, 133 and 100 MHz
bus frequencies. Three chip enable (CE) inputs permit easy memory expansion. Burst operation is initiated in one of two ways: the controller
address strobe (ADSC), or the processor address strobe (ADSP). The burst advance pin (ADV) allows subsequent internally generated burst
addresses.
Read cycles are initiated with ADSP (regardless of WE and ADSC) using the new external address clocked into the on-chip address register
when ADSP is sampled Low, the chip enables are sampled active, and the output buffer is enabled with OE. In a read operation the data accessed
by the current address, registered in the address registers by the positive edge of CLK, are carried to the data-out registers and driven on the
output pins on the next positive edge of CLK. ADV is ignored on the clock edge that samples ADSP asserted, but is sampled on all subsequent
clock edges. Address is incremented internally for the next access of the burst when ADV is sampled Low, and both address strobes are High.
Burst mode is selectable with the LBO input. With LBO unconnected or driven High, burst operations use a Pentium
®
count sequence. With
LBO driven LOW, the device uses a linear count sequence suitable for PowerPC
™
and many other applications.
Write cycles are performed by disabling the output buffers with OE and asserting a write command. A global write enable GWE writes all 32/
36 bits regardless of the state of individual BW[a:d] inputs. Alternately, when GWE is High, one or more bytes may be written by asserting
BWE and the appropriate individual byte BWn signal(s).
BWn is ignored on the clock edge that samples ADSP Low, but is sampled on all subsequent clock edges. Output buffers are disabled when BWn
is sampled LOW (regardless of OE). Data is clocked into the data input register when BWn is sampled Low. Address is incremented internally to
the next burst address if BWn and ADV are sampled Low.
Read or write cycles may also be initiated with ADSC instead of ADSP. The differences between cycles initiated with ADSC and ADSP follow.
• ADSP must be sampled HIGH when ADSC is sampled LOW to initiate a cycle with ADSC.
• WE signals are sampled on the clock edge that samples ADSC LOW (and ADSP High).
• Master chip enable CE0 blocks ADSP, but not ADSC.
AS7C33128PFS32A and AS7C33128PFS36A family operates from a core 3.3V power supply. I/Os use a separate power supply that can operate
at 2.5V or 3.3V. These devices are available in a 100-pin 14 × 20 mm TQFP package.
Capacitance
Parameter
Input capacitance
I/O capacitance
GWE
L
H
H
H
Symbol
C
IN
C
I/O
Signals
Address and control pins
I/O pins
BWE
X
L
H
L
BWn
X
L
X
H
Test conditions
V
IN
= 0V
V
IN
= V
OUT
= 0V
Max
5
7
WEn
T
T
F*
F
*
Unit
pF
pF
Write enable truth table (per byte)
.H\
X = Don’t Care, L = Low, H = High, T = True, F = False; *= Valid read; n = a, b, c, d; WE, WEn = internal write signal.
Burst Order
Starting Address
First increment
Second increment
Third increment
Interleaved Burst Order
LBO=1
00
01
10
11
01
00
11
10
10
11
00
01
11
10
01
00
Starting Address
First increment
Second increment
Third increment
Linear Burst Order
LBO=0
00
01
10
11
01
10
11
00
10
11
00
01
11
00
01
10
1 PowerPC
™
is a trademark International Business Machines Corporation.
3/4/02; v.1.4
Alliance Semiconductor
P. 2 of 13
AS7C33128PFS32A
AS7C33128PFS36A
®
Signal descriptions
Signal
CLK
A0–A16
DQ[a,b,c,d]
CE0
CE1, CE2
ADSP
ADSC
ADV
GWE
BWE
BW[a,b,c,d]
OE
LBO
FT
ZZ
I/O
I
I
I/O
I
I
I
I
I
I
I
I
I
I
I
I
Properties
CLOCK
SYNC
SYNC
SYNC
SYNC
SYNC
SYNC
SYNC
SYNC
SYNC
SYNC
ASYNC
STATIC
default =
HIGH
STATIC
ASYNC
Description
Clock. All inputs except OE, FT, ZZ, LBO are synchronous to this clock.
Address. Sampled when all chip enables are active and ADSC or ADSP are asserted.
Data. Driven as output when the chip is enabled and OE is active.
Master chip enable. Sampled on clock edges when ADSP or ADSC is active. When CE0 is
inactive, ADSP is blocked. Refer to the Synchronous Truth Table for more information.
Synchronous chip enables. Active HIGH and active Low, respectively. Sampled on clock
edges when ADSC is active or when CE0 and ADSP are active.
Address strobe processor. Asserted LOW to load a new bus address or to enter standby
mode.
Address strobe controller. Asserted LOW to load a new address or to enter standby mode.
Advance. Asserted LOW to continue burst read/write.
Global write enable. Asserted LOW to write all 32/36 bits. When High, BWE and BW[a:d]
control write enable.
Byte write enable. Asserted LOW with GWE = HIGH to enable effect of BW[a:d] inputs.
Write enables. Used to control write of individual bytes when GWE = HIGH and BWE =
Low. If any of BW[a:d] is active with GWE = HIGH and BWE = LOW the cycle is a write
cycle. If all BW[a:d] are inactive the cycle is a read cycle.
Asynchronous output enable. I/O pins are driven when OE is active and the chip is in read
mode.
Count mode. When driven High, count sequence follows Intel XOR convention. When
driven Low, count sequence follows linear convention.
This signal is internally pulled High.
18
Flow-through mode.When low, enables single register flow-through mode. Connect to
V
DD
if unused or for pipelined operation.
Sleep. Places device in low power mode; data is retained. Connect to GND if unused.
Absolute maximum ratings
Parameter
Power supply voltage relative to GND
Input voltage relative to GND (input pins)
Input voltage relative to GND (I/O pins)
Power dissipation
DC output current
Storage temperature (plastic)
Temperature under bias
Symbol
V
DD
, V
DDQ
V
IN
V
IN
P
D
I
OUT
T
stg
T
bias
Min
–0.5
–0.5
–0.5
–
–
–65
–65
Max
+4.6
V
DD
+ 0.5
V
DDQ
+ 0.5
1.8
50
+150
+135
Unit
V
V
V
W
mA
o
C
o
C
Stresses greater than those listed under
Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress rating only and functional operation of
the device at these or any other conditions outside those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum
rating conditions may affect reliability.
3/4/02; v.1.4
Alliance Semiconductor
P. 3 of 13
AS7C33128PFS32A
AS7C33128PFS36A
®
Synchronous truth table
CE0
H
L
L
L
L
L
L
L
L
X
X
X
X
H
H
H
H
L
X
H
X
H
CE1
X
L
L
X
X
H
H
H
H
X
X
X
X
X
X
X
X
H
X
X
X
X
CE2
X
X
X
H
H
L
L
L
L
X
X
X
X
X
X
X
X
L
X
X
X
X
ADSP
X
L
H
L
H
L
L
H
H
H
H
H
H
X
X
X
X
H
H
X
H
X
ADSC
L
X
L
X
L
X
X
L
L
H
H
H
H
H
H
H
H
L
H
H
H
H
ADV
X
X
X
X
X
X
X
X
X
L
L
H
H
L
L
H
H
X
L
L
H
H
WEn
1
OE
X
X
X
X
X
L
H
L
H
L
H
L
H
L
H
L
H
X
X
X
X
X
Address accessed
NA
NA
NA
NA
NA
External
External
External
External
Next
Next
Current
Current
Next
Next
Current
Current
External
Next
Next
Current
Current
CLK
L to H
L to H
L to H
L to H
L to H
L to H
L to H
L to H
L to H
L to H
L to H
L to H
L to H
L to H
L to H
L to H
L to H
L to H
L to H
L to H
L to H
L to H
Operation
Deselect
Deselect
Deselect
Deselect
Deselect
Begin read
Begin read
Begin read
Begin read
Cont. read
Cont. read
Suspend read
Suspend read
Cont. read
Cont. read
Suspend read
Suspend read
Begin write
Cont. write
Cont. write
Suspend write
Suspend write
DQ
Hi
−
Z
Hi
−
Z
Hi
−
Z
Hi
−
Z
Hi
−
Z
Hi
−
Z
2
Hi
−
Z
Hi
−
Z
2
Hi
−
Z
Q
Hi
−
Z
Q
Hi
−
Z
Q
Hi
−
Z
Q
Hi
−
Z
D
3
D
D
D
D
X
X
X
X
X
X
X
F
F
F
F
F
F
F
F
F
F
T
T
T
T
T
2
Q in flow through mode.
3For write operation following a READ,
OE
must be HIGH before the input data set up time and held HIGH throughout the input hold time.
Key: X = Don’t Care, L = Low, H = High.
1
See “Write enable truth table” on page 2 for more information.
3/4/02; v.1.4
Alliance Semiconductor
P. 4 of 13
AS7C33128PFS32A
AS7C33128PFS36A
®
Recommended operating conditions
Parameter
Supply voltage
3.3V I/O supply voltage
2.5V I/O supply voltage
Address and
control pins
I/O pins
Ambient operating temperature
Symbol
V
DD
V
SS
V
DDQ
V
SSQ
V
DDQ
V
SSQ
V
IH
V
IL
V
IH
V
IL
T
A
Min
3.135
0.0
3.135
0.0
2.35
0.0
2.0
–0.5
2
2.0
–0.5
2
0
Nominal
3.3
0.0
3.3
0.0
2.5
0.0
–
–
–
–
–
Max
3.6
0.0
3.6
0.0
2.9
0.0
V
DD
+ 0.3
0.8
V
DDQ
+ 0.3
0.8
70
Unit
V
V
V
V
V
°
C
Input voltages
1
1 Input voltage ranges apply to 3.3V I/O operation. For 2.5V I/O operation, contact factory for input specifications.
2 V
IL
min. = –2.0V for pulse width less than 0.2 × t
RC
.
TQFP thermal resistance
Description
Thermal resistance
(junction to ambient)
1
Thermal resistance
(junction to top of case)
1
1 This parameter is sampled.
Conditions
Test conditions follow standard test methods and
procedures for measuring thermal impedance, per EIA/
Has any friend debugged the driver of the DE mode screen under ARM? LCD is generally in SYNC mode, but I now have a screen that is DE MODE ONLY, without HSYNC and VSYNC. How do I adjust it?...
I used STM32 to write a simple IO operation and the following error occurred. The tool is IAR5.5. Please take a look. Warning[Pe223]: function "GPIO_ReadIuputData" declared implicitly E:\YZX\MAKE\IAR ...
My program was made with a resolution of 320*240. Now my PDA has been replaced with 640*480, and the interface is a mess. I want to change the resolution. This is the easiest way. I hope you can help ...
It's funny, it can be regarded as a way to broaden your mind, [color=#33463f][backcolor=rgb(250, 250, 250)][font=Arial, Helvetica, sans-serif]Sometimes things are very simple, but you think too much! ...
Our company specializes in the production of circuit boards, single (FR-4, CEM-1), double, multi-layer (4-18 layers), aluminum substrates, LED super-long boards, toothpick boards, small batches and la...
1 Introduction
As an emerging microfabrication technology, micro-electromechanical system (MEMS) technology has begun to be applied in various fields. It can integrate functions such as inform...[Details]
Instrument stepper motor
The stepper motor is an open-loop control element that converts electrical pulse signals into angular displacement or linear displacement. In the case of non...[Details]
A standard cell
is an electrochemical
cell
used as a voltage reference standard in many electrical standards laboratories
. If properly maintained, standard cells are very stable. The ...[Details]
The automotive lighting and signal control system is responsible for controlling the vehicle's lighting, signal lights, electric horns, reversing and brake buzzers. Traditional automotive lighting...[Details]
The typical fault troubleshooting listed below is for reference of maintenance personnel.
When the computer is turned on, the indicator light is off and there is no screen display
Mainte...[Details]
Flooded Batteries
This battery developed in Germany can be used to power flashlights, strobe lights and toys as long as it is filled with water. This battery can be stored for 50 years and can...[Details]
Introduction
Liquid crystal, as a display device, is widely used in low-power products such as instruments, meters, and electronic equipment with its unique advantages. In the past, the displ...[Details]
Capacitance Measurement
Used to verify that capacitors meet the manufacturer's specifications. For quality control, a group of capacitors may be placed in an environmental chamber and the cap...[Details]
Introduction
Automakers are working to reduce vehicle weight to reduce CO2 emissions and improve fuel efficiency. Designers are therefore seeking new technologies and design techniques that can...[Details]
Abstract: With the development and construction of BeiDou II system, China will shift from the situation dominated by GPS to the situation dominated by BeiDou II global navigation system independen...[Details]
1. Proposal of
reconfigurable
measurement and control system
The measurement and control system generally refers to a system based on
computers
to realize data acquisition a...[Details]
A stepper motor is an electromagnetic mechanical device that converts an electrical pulse signal into an angular displacement or a linear displacement. The stability and reliability of a stepper mo...[Details]
The invention of the steam engine ushered in the first conversion of internal energy and mechanical energy for mankind, and the birth of the internal combustion engine at the end of the 19th centur...[Details]
1 Introduction
With the rapid economic development, my country's electricity demand has been growing at a rate of more than 20% per year. According to the current economic development trend an...[Details]
introduction
When it comes to the production of mobile phone lithium-ion batteries, the first thing that comes to mind is Japan's industrialized mechanical assembly line, NOKIO, MOTOLROLA's st...[Details]
ARM Technology
京公网安备 11010802033920号
EEWORLD
