[i=s] This post was last edited by Beifang on 2018-9-29 08:50[/i] 1. As mentioned in the previous article, if this NN model is to run, the preliminary preparation work is indeed quite large. The examp...
We want to make a multi-channel buzzer. I checked many circuit diagrams and they all use 74LS273. But we don't have this chip, so we can only use a substitute. But I don't know what gates the internal...
msp430f5529 controls DHT11. The program seems to be ported to msp430g2553. The LCD data is displayed incorrectly. I think it may be a problem with the clock setting. I directly modified it based on th...
[font=微软雅黑][size=2][color=#000000]Today I bring you a familiar textbook: "Electrical Engineering Sixth Edition", both volumes are available, download address: [/color] [color=#333333]Electrical Engine...
For 80,000
ZTE
(000063.SZ) employees and more Chinese ICT (information and communication technology) industry practitioners, the news from across the ocean on the evening of April 16 kept t...[Details]
In the actual project development process, we often need to get the running time of a section of code. The usual method is to use an oscilloscope to measure it. This blog post will use SysTick to acc...[Details]
I recently upgraded MDK to V5.25 and found that there are many libraries in the Managing Run-Time Environment. Compared with the past, it is much better, from the bottom-level driver to the upper-le...[Details]
0. Preparation First use st-link to connect the stm32 core board and PC for burning St-link Stm32 3.3V 3.3V GND GND SWDIO PART SWCLK DCLK Then connect with USB serial port board to v...[Details]
I used STM32CubeMX V4.22.1 to generate a project including EHT and Lwip. The debugging has been abnormal. After careful inspection, the following problems were found: 1. The hardware uses LAN8720A, b...[Details]
introduction In the general project development process, two or more microcontrollers are often required to communicate to complete data transmission. For example, a quadcopter wirelessly transmits d...[Details]
Timing and protocol are two key points in digital system debugging, and they are also where logic analyzers can play their most valuable role. How can we use a logic analyzer to quickly complete wiri...[Details]
1 Introduction Due to the special working environment of coal mine production, the production process is more dangerous and unsafe than the general industry. With the continuous increase in c...[Details]
Every era has anxiety that has nowhere to go. Let's follow the embedded editor to learn about the relevant content.
The anxiety of the post-Internet era is that if you don’t revolutionize ...[Details]
The photovoltaic industry has become a new business card for China to the world. It not only represents China's leading technology, but also constantly breaks various records with its development spee...[Details]
1. Function and purpose There are two pins BOOT0 and BOOT1 on each STM32 chip. The level status of these two pins when the chip is reset determines which area the program starts from after th...[Details]
environment: Host: XP Development environment: MDK4.23 MCU:STM32F103CBT6 illustrate: Collect AD through pins PA1 and PA2. Collect AD 10 times for each channel. #include "ad_driver.h" //Global ...[Details]
/* Unfortunately, it cannot generate a standard 38kHz frequency square wave, there is a little error*/ #include reg51.h #define uchar unsigned char #define uint unsigned int sbit Waveout=P1^0; //P...[Details]
The key is the configuration of registers. The T1 timer (16 bits) of CC2530 needs to configure three registers: T1CTL, T1STAT, IRCON Here is just a brief introduction. For more details, please refer ...[Details]
GD32 MCU
京公网安备 11010802033920号
EEWORLD
