EXPOSED PAD (PIN 17) IS SGND, MUST BE SOLDERED TO PCB
UD PACKAGE
16-LEAD (3mm 3mm) PLASTIC QFN
T
JMAX
= 125°C,
θ
JA
= 45°C/W
EXPOSED PAD (PIN 17) IS PGND, MUST BE SOLDERED TO PCB
ORDER INFORMATION
LEAD FREE FINISH
LTC3604EUD#PBF
LTC3604IUD#PBF
LTC3604EMSE#PBF
LTC3604IMSE#PBF
TAPE AND REEL
LTC3604EUD#TRPBF
LTC3604IUD#TRPBF
LTC3604EMSE#TRPBF
LTC3604IMSE#TRPBF
PART MARKING*
LFPT
LFPT
3604
3604
PACKAGE DESCRIPTION
16-Lead (3mm
×
3mm) Plastic QFN
16-Lead (3mm
×
3mm) Plastic QFN
16-Lead Plastic MSOP
16-Lead Plastic MSOP
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
3604f
2
LTC3604
ELECTRICAL CHARACTERISTICS
SYMBOL
V
VIN
I
Q
PARAMETER
Input Supply Range
Input DC Supply Current
Forced Continuous Operation
Sleep Current
Shutdown
Feedback Reference Voltage
Reference Voltage Line Regulation
Output Voltage Load Regulation
Feedback Pin Input Current
Error Amplifier Transconductance
Minimum On-Time
Minimum Off-Time
Valley Switch Current Limit
Oscillator Frequency
The
l
denotes the specifications which apply over the full operating
junction temperature range, otherwise specifications are at T
J
= 25°C. V
VIN
= 12V, unless otherwise specified.
CONDITIONS
l
MIN
3.6
TYP
MAX
15
1000
500
25
0.606
UNITS
V
μA
μA
μA
V
%/V
%
nA
mS
ns
ns
A
MHz
MHz
MHz
mΩ
mΩ
V
V
V
%
V
V
V
V
μA
%
%
%
%
μs
Ω
μA
μs
mV
μA
V
V
V
μA
μA
MODE = 0V
MODE = INTV
CC
, V
FB
> 0.6V
RUN = 0V
l
V
FB
ΔV
LINEREG
ΔV
LOADREG
I
FB
g
m(EA)
t
ON(MIN)
t
OFF(MIN)
I
LIM
f
OSC
0.594
V
VIN
= 3.6V to 15V
ITH = 0.6V to 1.6V
V
FB
= 0.6V
ITH = 1.2V
V
ON
= 1V, V
IN
= 4V
V
IN
= 6V
V
RT
= INTV
CC
R
RT
= 160k
R
RT
= 80k
2.6
1.4
1.7
3.4
700
300
14
0.600
0.01
0.1
±30
2.0
20
40
3.4
2
2
4
130
100
17.5
16.5
3.3
0.6
2.75
2.45
1.25
1.0
0
8
–8
–5
5
40
15
0.01
400
0.3
1.4
60
4.3
2.6
2.3
4.6
R
DS(ON)
V
VIN(OV)
V
INTVCC
ΔINTV
CC
V
UVLO
V
RUN
I
RUN(LKG)
V
FB_GB
V
FB_BG
t
PGOOD
R
PGOOD
I
SW(LKG)
t
SS
V
FB_TRACK
I
TRACK
V
MODE/SYNC
Top Switch On-Resistance
Bottom Switch On-Resistance
V
IN
Overvoltage Lockout Threshold
INTV
CC
Voltage
INTV
CC
Load Regulation (Note 4)
INTV
CC
Undervoltage Lockout
Threshold
RUN Threshold
RUN Leakage Current
PGOOD Good-to-Bad Threshold
PGOOD Bad-to-Good Threshold
Power Good Filter Time
PGOOD Pull-Down Resistance
Switch Leakage Current
Internal Soft-Start Time
TRACK Pin
TRACK Pull-Up Current
MODE Threshold Voltage
SYNC Threshold Voltage
MODE Input Current
V
IN
Rising
V
IN
Falling
3.6V < V
IN
< 15V
I
INTVCC
= 0mA to 20mA
INTV
CC
Rising, V
IN
= INTV
CC
INTV
CC
Falling, V
IN
= INTV
CC
RUN Rising
RUN Falling
V
VIN
= 15V
FB Rising
FB Falling
FB Rising
FB Falling
10mA Load
V
RUN
= 0V
V
FB
from 10% to 90% Full Scale
TRACK = 0.3V
MODE V
IH
MODE V
IL
SYNC V
IH
MODE = 0V
MODE = INTV
CC
l
l
16.8
15.8
3.13
18
17
3.45
2.9
1.29
1.03
±3
10
–10
l
l
1.21
0.97
–3
3
20
0.28
l
l
l
1
700
0.315
1.0
0.4
0.95
–1.5
1.5
I
MODE
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
The LTC3604E is guaranteed to meet performance specifications
from 0°C to 85°C. Specifications over the –40°C to 125°C operating
junction temperature range are assured by design, characterization, and
correlation with statistical process controls. The LTC3604I is guaranteed
over the full –40°C to 125°C operating junction temperature range. The
maximum ambient temperature is determined by specific operating
conditions in conjunction with board layout, the rated package thermal
resistance and other environmental factors.
3604f
3
LTC3604
ELECTRICAL CHARACTERISTICS
Note 3:
T
J
is calculated from the ambient temperature, T
A
, and power
dissipation, P
D
, according to the following formula:
T
J
= T
A
+ (P
D
•
θ
JA
)
where
θ
JA
= 45°C/W for the QFN package and
θ
JA
= 38°C/W for the MSOP
package.
Note 4:
Maximum allowed current draw when used as a regulated output
is 5mA. This supply is only intended to provide additional DC load current
as needed and not intended to regulate large transient or ac behavior as
these waveforms may impact LTC3604 operation.
Note 5:
This IC includes overtemperature protection that is intended
to protect the device during momentary overload conditions. Junction
temperature will exceed 125°C when overtemperature protection is active.
Continuous operation above the specified maximum operating junction
The teacher asked me to make an accelerometer to record a person's walking route for a day. Now I need to determine the accelerometer model, board model and SD card to use. Please recommend. Especiall...
When debugging the RTC routine, I found that the system crashed every time I simulated the printf function. So I searched for solutions online and saw that the simplest and most effective method was t...
ARM Basics The ARM processor has a total of 37 registers. These include: **31 general-purpose registers, including the program counter (PC). These registers are all 32-bit registers. **6 status regist...
Now I have written a program similar to ping and run it on a PC, but the program does not send a ping packet once a second. Instead, it immediately sends another ping packet if it receives a response ...
The circuit shown in the figure is a three-digit tachometer used to measure low frequency signals with a repetitive time interval of 0.235 to 15 seconds. The tachometer has a speed range of 4 to 255 r...[Details]
This article introduces a miniature home electrocardiograph. The instrument has powerful functions: display monitoring, storage, playback, printing, record management, power alarm, telephone or Intern...[Details]
JTAG Technology Introduction
One disadvantage of shrinking technology is that the complexity of testing small devices increases dramatically. When the board area is large, the board is tested...[Details]
introduction
In engineering practice, ultrasonic waves are often used to measure distances because of their strong directivity, slow energy consumption, and long propagation distance in th...[Details]
IPTV (Internet Protocol TV or Interactive Personal TV), also known as interactive network television, is a new technology that uses broadband network infrastructure, takes home televisions or comp...[Details]
Anyone who has owned a laptop computer will have noticed that when running on battery power, their portable device behaves differently than when running on AC mains power—the display dims, the proc...[Details]
Capacitive sensing user interfaces are emerging as a practical and innovative alternative to mechanical buttons in mobile phones. While capacitive sensors can be viewed as a drop-in replacement fo...[Details]
0Introduction
Microactuators, as driving components of microelectromechanical systems (MEMS), have been widely studied. In recent years, actuators made of hard magnetic and soft magnetic m...[Details]
After more than ten years of technological development and application market cultivation, biometric technology has been applied on a large scale in many application fields. As far as the Chinese m...[Details]
As mobile phones and other portable devices have more functions, there are more potential input and output (I/O) channels for electrostatic discharge (ESD) voltage to enter, including keyboards, bu...[Details]
With the development of science and technology, the improvement of living standards and the acceleration of the pace of modern cities, people are increasingly pursuing more convenient, practical an...[Details]
Facing the global financial tsunami, in order to stimulate the economy, the country will invest 2 trillion yuan in railways during the "Eleventh Five-Year Plan". The large-scale construction of rai...[Details]
0 Introduction
With the rapid development of modern science and technology and the progress of society, service robots are becoming more and more closely connected with people's lives,...[Details]
1 Introduction
The brushless DC motor uses an electronic commutation device to replace the mechanical commutation device of the traditional DC motor, and has similar mechanical character...[Details]
0 Introduction
Heart rate is a very important vital information in the human body, and traditional pulse diagnosis, due to its qualitative and subjective nature, affects the accuracy of he...[Details]
51mcu
京公网安备 11010802033920号
EEWORLD
